Axial Piston Pump Series PV - Pascal

1 Axial Piston Pump Series PV. Variable Displacement Catalogue HY11-3243/UK. August 2002. Catalogue HY11-3243/UK Axial Piston pump Series PV. Note This document and other information from Parker Hannifin GmbH, its subsidiaries, sales offices and authorized distributors provide product or system options for further investigation by users having technical expertise. Before you select or use any product or system it is important that you analyse all aspects of your application and review the information concerning the product or system in the current product catalogue. Due to the variety of operating conditions and applications for these products or systems, the user, through his own analysis and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance and safety requirements of the application are met.

2 The products are subject to change by Parker Hannifin GmbH at any time without notice. PI PVplus RH. 2 Parker Hannifin GmbH. Hydraulic Controls Division Kaarst, Germany Catalogue HY11-3243/UK Axial Piston pump Table of contents Series PV. Description Page Introduction 4. Characteristics 5. Ordering code 6. Noise levels 8. Noise reduction measures 9. Efficiency and case drain flows 10. Dimensions 14. Pump combinations Dimensions 26. Thru drive, shaft load limitations 28. Compensators Dimensions / Seal kit compensators 29. Pressure compensators 30. Load-sensing compensators 31. Horse power compensators 32. Electrohydraulic p/Q control 34. Hydraulic circuit, ordering examples PVAP** 36. Hydraulic circuit, ordering examples PVAC** 38. Accessories 40. General installation information 41.

3 PI PVplus RH. 3 Parker Hannifin GmbH. Hydraulic Controls Division Kaarst, Germany Catalogue HY11-3243/UK Axial Piston pump Introduction Series PV. Pump with standard pressure compensator code F*S Pump with load-sensing compensator code FFC. 0,8. Q PF Q. L P1 A L P1 A. PM P L P1 A PM P L P1 A. p p S L = included S L = included Technical Features Mounting interface according to VDMA-standards sheet 24560 part 1. With thru drive for single and multiple pumps Standard: 4-hole flange ISO 3019/2 (metric). Op- Swash plate type for open circuit tional: 4-hole flange ISO 3019/1 (SAE). Large servo Piston with strong bias spring achieves fast response; for PV046. upstroke < 70 ms ; downstroke < 40 ms Note: follow installation instructions! Reduced pressure peaks due to active decompres- sion of system at downstroke Also at low system pressure reliable compensator operation.

4 Lowest compensating pressure <10 bar Nine Piston and new precompression technology (precompression filter volume) result in unbeaten low outlet flow pulsation Rigid and FEM-optimized body design for lowest noise level Complete compensator program Thru drive for 100% nominal torque Pump combinations (multiple pumps ) of same size and model and mounting interface for basically all metric or SAE mounting interfaces Pump with horse power compensator code *LB Pump with electrohydr. displacement control code *PV. PP. UQ Q. L P1 A L P1 A. PM P L P1 A PL Q PM P L P1 A. U. s UQ. p p S L = included S L = included PI PVplus RH. 4 Parker Hannifin GmbH. Hydraulic Controls Division Kaarst, Germany Catalogue HY11-3243/UK Axial Piston pump Characteristics Series PV. Technical data Displacement [cm3/rev] from 16 to 270.

5 Operating pressures Outlet [bar] nominal pressure pN 350. [bar] max. pressure pmax. 420 1). [bar] drain port 2 2). [bar] Inlet min. (absolute). [bar] max. 16. Minimum speed [min-1] 300 min-1. Pump with standard pressure comp. Pump with horse power comp. Mounting interface 4-hole flange ISO 3019/2. optional ISO 3019/1, SAE. Installation drain port as high as possible 1). peak pressure only 2). peak pressure only, special version up to 20bar available Pump combinations See pages 26 27 Combination PV/PV Combination PV/gear pump Selection table 1). Model Max. displacement Output flow Input horse power in kW Max speed Weight in cm3/rev in l/min at 1500 min-1 at 1500 min-1 and 350 bar in min-1 in kg PV016 16 24 PV020 20 30 3000 19. PV023 23 PV032 32 48 31. PV040 40 60 39 2800 30. PV046 46 69 45.

6 PV063 63 2800. PV080 80 120 78 2500 60. PV092 92 138 2300. PV140 140 210 136 2400 90. PV180 180 270 175 2200 90. PV270 270 405 263 1800 172. 1). The maximum speed ratings are shown for an inlet pressure of 1 bar (absolute) and for a fluid viscosity of = 30 mm /s. PI PVplus RH. 5 Parker Hannifin GmbH. Hydraulic Controls Division Kaarst, Germany Catalogue HY11-3243/UK Axial Piston pump Ordering Code Series PV. PV. pump compensator Axial Piston Size Variation Threads 2nd Compensator Design pump and pump Series : variable displacement not required displacement for order high pressure Rotation Mounting version code Thru drive Seals see opposite page Code Displacement Code Seals 016 16 cm /U N NBR. 020 20 cm /U V FPM. 023 23 cm /U E EPR. 032 32 cm /U. 040 40 cm /U. 046 46 cm /U. 063 63 cm /U Code 2nd pump option7).

7 080 80 cm /U single pump, no 2nd pump 092 92 cm /U 1. and coupling 140 140 cm /U. 2 PV140 or PV180 mounted 180 180 cm /U. 3 PV or PVM pump mounted 270 270 cm /U. 4 gear pump Series PGP mounted 5 PAV/PAF up to cm /rev 1). Code Rotation mounted R clockwise 6 PAV10 or PAF8-10 mounted L counter clockwise 7). Specify 2nd pump with full model code 1). when looked on shaft Code Variation Code Thru drive option 1 standard no adaptor for 2nd pump 9 reduced displace- single pump T prepared for thru drive ment adjusted 2). 2). for order specify displace- with adaptor for 2nd pump ment Y8) SAE AA, A SAE A, Code Mounting interface Shaft B SAE B, D 4-hole flange cylindric, key C9) SAE C, 127mm SAE D10) SAE D, E 4-hole flange splined, SAE. ISO E11) SAE E, F3) 3019/1 4-hole flange cylindric, key G12) metric, 63mm G3) 4-hole flange splined, SAE.

8 H metric, 80mm K metr. ISO 4-hole flange cylindric, key J metric, 100mm L 3019/2 4-hole flange splined, DIN 5480. K9) metric, 125mm 3). codes F and G only for PV140/180, see dimension sheet L10) metric, 160mm M11) metric, 200mm Code Port 4) Threads5) 8). only for PV016 - PV023. 9). 1 BSPP metric only for PV032 and larger 10). 3 UNF UNC only for PV063 and larger 11). only for PV270. 46) BSPP metr. M14 12). only for PV016 - PV092. 7 ISO 6149 UNC. 8 ISO 6149 metric1). 4). drain, gauge and flushing ports 5). all mounting and connecting threads 6). for PV063-PV180 only: pressure port 1 1/4" with 4 x M14 instead of 4 x M12. PI PVplus RH. 6 Parker Hannifin GmbH. Hydraulic Controls Division Kaarst, Germany Catalogue HY11-3243/UK Axial Piston pump Ordering Code Series PV. PV. Compensator Pump Compensator Design Series : not required for order Standard pressure compensator Electrohydraulic compensator Code Compensator option Code Compensator option 0 0 1 No compensator Pilot pressure supply F D S 10 - 140 bar, spindle + lock nut F Standard (internal), no shuttle valve F H S 40 - 210 bar, spindle + lock nut W With shuttle valve, comp.

9 Horizontal F W S 70 - 350 bar, spindle + lock nut Function Remote compensator options P Proportional displacement control F R Remote pressure compensator Variation F S Variation R, for quick unload valve V Standard, no pressure compensation F F Load-Sensing compensator Proportional pilot valve D DSAE1007P07 KLAF mounted F T Two valve load-sensing compensator 14). Variations for remote compensator Z Variation R, accessories mounted C external pressure pilot 13) R Remote pressure comp. NG6 interface 1 NG6/D03 interface top side Variation R, Pressure sensor and P Pilot valve PVAC1P*M* mounted G proportional pilot valve mounted for Proportional pilot valve type pressure resp. horse power control D. DSAE1007P07 KLAF mounted Remote pressure comp., NG6 interface S top side, for quick unload valve L Pilot valve with DIN lock mounted Z Accessory mounted 14) Variation S, pressure sensor and T proportional pilot valve mounted for pressure resp.

10 Horse power control Horse power compensator Remote pressure comp., NG6 interface top Code Displacement Compensator option P side, for preload and quick unload manifold 016 032 063 Nom. HP [kW] Nom. torque Variation P, pressure sensor and 023 046 092 140 180 270 at 1500 min-1 [Nm] E proportional pilot valve mounted for B x 3 pressure resp. horse power control C x 4 26. D x x 36. E x x 49. G x x x 11 71. H x x x 15 97. K x x x 120. M x x x x 22 142. S x x x 30 195. T x x x x 37 240. U x x x x 45 290. W x x x 55 355. Y x x 75 485. Z x x 90 585. 2 x 110 715. 3 x 132 850. Function L x x x x x x Horse power compensator Horse power compensator and C x x x x x x load-sensing Variation A x x x x x x NG6 interface top side B x x x x x x no pressure compensation adjustable C x x x x x x pressure compensation 13).