Tajima Machine Error List - theembroiderywarehouse.com

1 Tajima Machine Error List_01No 500 character function code when data setPress RESET and set the data set_02 Tajima tape complement Error . ( The same +/--Correct the tapenumerics are entered in a single stitch data_03 Data is involved in the tape end codeCorrect the tape_04 Improper function code position. Or, wrongCorrect the tape, or select proper format was writing errorExpand memory capacity, or replace memory tape signal troubleAdjust reader, or replace unit_09 PTR motion is in disorder. Reader does notCheck connection of reader the tape for more than 5 seconds11 Data set incompleteAfter properly setting data, start stitch backStitch back is possible up to 71 stitches for tape operation and starting point for memory forward ( When offset is set) Set the offset value to zero, or move the frame by a distance of offsetand move the format 5 is selected although no designsSave design to memoryare stored in 30 designs have been stored in memory, Only 30 designs can be stored in memory.)

2 Remove unnecessary format 2, or 4 was the data setting, the number of that Save design to memory is capacity shortage during unnecessary command by bar switch is given duringexecution of mode 5, 6, offset or home return31 Stop command by bar switch is givenduring color change51No stop position signal is outputEncoder or Machine card limit switch the frame to its working motor driver trouble (X, Y)Check PMD drive units. 54 Left and right limits on the color changeCheck Machine card, needle position change takes over 5 secondsCheck Machine card, BP card56 Color change, half-turn cam signal needle position card, BP for a mechanical bind in the color change position signal troubleCheck needle position for a mechanical bind in the color change turn of the main shaft motor takes over5 seconds59 The cap frame moves more than 75mm from Inspect the photo interrupterthe cap frame zero point when searching60 The embroidery space of the cap frame is Move the cap frame to the correct start point or decrease the the fixed position signal is not detected.

3 Return the main shaft to the fixed position. Check the encoder signal Main shaft Z signal)212 Needle bar is in lowering positionMove up the needle bar by needle bar frame has traveled left, exceeding the position set by the frame limit222 The frame has traveled right, exceeding the position set by the frame limitMove the frame manually so that the design fits in the embroidery frame has traveled up, exceeding the position set by the frame limit224 The frame has traveled down, exceeding the position set by the frame limit225 Travel outside the set embroidery area( When the software frame limit is set, or on cap machines)226 Absolute origin limit (+X, -Y) detectedCorrect the frame limit position(s)228 Table up/down operation was attempted al-Move the frame back to the rear most end before moving the table the frame was in the front side position234 Faulty laser unitTurn off power and wait 5 seconds. Turn on power again, if Error 234remains check the laser unit.

4 Check chiller (cooling unit) 242 The-M-axis rotation range (+/--32 rotations) isPress the RESET key and then manually rotate the M-axis in the reverse when using the M-axis manualOr, press the RESET key and then start the functionH position251 Low oil in the auto lube oil to the lubrication status of the air valve (vacuum) does notCheck the air pressure supplied to the air limit of the laser protect cover is notCheck/replace the lower limit sensor, check/adjust air pressuredetected254 Upper limit of the laser protect cover is notCheck/replace the upper limit sensor, check/adjust air peripheral device is defectiveCheck the peripheral device and the connection to frame travel or frame forward/back isSet the Z-axis to H positionCE attempted when the Z-axis is not positioned at272 Manual nipple lifting is performed duringPress the RESET keycoiling embroidery281 The target needle position is not detected Turn the shaft of the color change box to check to see if needle positionwithin 15 seconds after the start of the color display is correct.

5 Correct display, action display, check color change sensor(s)291* Upper thread Breakage is detected* Check the upper/under thread* Tension base card is faulty* Replace the tension base card293 Under thread breakage is detectedCheck the bobbin thread2B1No response is received for 5 seconds since* Check connection of serial device (TFD, PC, etc.)the operation was started using a serial I/F* Repair or correct the design data( Serial I/F device is not correctly connected)2B2 Tajima code complement Error . Same + andCorrect the design data2B3 Data exists in an end codeCorrect the design data2B4 Code format Error (A stitch code does not Correct the design dataexist at the third character.)2B5 Reading Error , stitch data over mmCorrect data2B6 The serial interface is not readySet the serial interface to the Communications Machine was started or frame forward Perform data setwas performed although data was not input2B8 When the pre-reading buffer becomes emptyDuring operation: Lower main shaft frame forward operation: Wait until all of the design data is write errorCheck the CPU or memory card.

6 Replace if necessary2 BAMemory capacity ExceededDelete unnecessary designs registered in memory2 BBFrame back exceeded the allowable rangeDo not perform further frame back2BC*No design is registered in memory*Register design in memory*An attempt was made to erase from memory *To erase from memory a design currently being embroidered, either set another design the current design being embroideredor data set the same design*An attempt was made to edit data * Do not edit (cleanup) design during embroidery( ) during embroidery2 BDEither a stop code or end code is detectedCorrect the design databefore the 3rd stitch code and end code are not set to be a Set again to make start code and end code be a pair if in satin convers., sequin, and boring code2C1 The Machine is started or frame forward/backDo not attempt to operate the Machine while performing setting on the panelis executed during setting the panel2C2 Incorrect option settingSet correctly2C2ON is set for both boring and laser unit)

7 Set OFF for DSW2-2 boring device and turn on the power after turning it off onceTLFD2C3"Pack" is not designatedDesignate packed designs2C4 The design stitch count is exceededConfirm the number of stitches in the design2C5An attempt was made to carry out laserWait until preheating is during laser preheating2C6 Machine operation was attempted, althoughDo not operate bobbin changer when the Machine is bobbin changer was running2 CBThe design is too large to be displayed within Reduce the design to be within the designated software frame designated software frame limit2 CDPower supply is turned OFF during designRewrite data to the memorydeletion or edit mode processing2 CERemote interlock activatesReset the remote interlock2 CFAn immediate stop came in from an externalCheck the external device or the connection to the external (TMLG, connector joint 16 JH082D1 Initial setting of laser power is not initial setting of laser power. (Teaching)_2E3 Power supply has been interrupted duringTurn ON the power and perform "Power Resume" *Encoder A signal status does not change for*Check encoder and encoder signal lines5 seconds*Check the main shaft driver for excitation*Motor or belt failureCheck the main motor and belt312 Encoder z signal status does not change*Check the encoder and encoder signal linesfor 5 seconds313 Clutch stopper disengagedEngage clutch stopper314 Main shaft rotation failureCheck the encoder/encoder signal line.)

8 Main motor and main shaft driver Error is detectedReplace the main shaft driver unit or mainn shaft motor317 The take-up lever clutch has received an Check or replace the joint-25 signal321 PMD failureCheck driver and X-axis pulse motor driver Error signal isReplace the X-axis driver unitdetected323A Y-axis pulse motor driver Error signal isReplace the Y-axis driver unitdetected324 Frame feed output when the needle penetratesDecrease the Machine operating speed. Check the rotary encoder and encoder the Error , usually occurs when the ATHSet parameter N-23 to 0 mm. If problem continues install software version BD or IMM ErrorMake sure Machine has at least version BD or problem persists, change IMM *Absolute origin could not be detected on the X *Find faulty origin sensor and adjust or Y axis*Cap Machine origin search Error * Check cap origin sensor and harness331 Bobbin Changer errorCheck bobbin changer origin errorCE/LE341An M-axis base point signal is not detectedReplace the M-axis base point sensor or its M-axis PMD abnormal signal is the mechanical parts related to the M-axis for abnormalities.

9 Check/replacethe M-axis incremental encoder or M-axis drive M-axis clutch driver has received an Check/replace the joint-25 signal346 The zig-zag PMD has received an abnormalCheck the parts related to the zigzag swing mechanism. After adjustment, reset the M-axis PMD abnormal signal is detectedCheck the parts related to the M-axis for abnormalities. After adjustment, press the RESET sequin driver has issued abnormal signalsCheck/replace sequin height position errorCheck BP card and needle position cardCE/LE371 Either an upper or lower position signal cannotAdjust the nipple lifter. Check/replace the input372ZB Signal errorCE372 The nipples do not move more than 1 secondPress the RESET key. Then check/replace the nipple lifting motor and/or theLGnipple position nipple position sensor issued an abnormal Press the reset key. Then change the nipple stroke by using the keys from 1 to the return key. Check/replace the nipple position input to position sensorsLE374 Nipple sensor signal abnormality, both inputshave signals375 The Z-axis driver (Z-axis release solenoid) hasCheck/replace the joint-25 an abnormal *The FX head needle position input data has* Set the number of needles at system software correctly.

10 Check/replacean errorcolor change sensor*The FX head needle position signal is not*Check/replace color change sensorinput while the main shaft is rotating382 The needle position signal status during*Check the color change motor and power supply circuitcolor change does not change for 1 second*Check the potentiometer (Needle position sensor)or more383*Incorrect input of needle position*Check the setting for number of needles in the parameter settings*No needle position signal is detected during*Check the potentiometer (needle position sensor)rotation of the main shaft383 Control Error of the D-axis drive motorTurn off the power, and then turn it on again. If code 383 is still displayed, replaceCEthe head card of the corresponding CE 1 rotation signal is given while the mainCheck color change sensor(s)shaft is running384 Control Error of the looper shaft drive Turn off the power, and then turn it on again. If code 384 is still displayed, replaceCEmotorthe head card of the corresponding CE does not move to the designated positionCheck/adjust/replace: compressor pressure, sensor, sensor wiring, electromagneticwhen during lense switchingvalve & wiring, lens fulcrum axis and shaft385Z-axis operation failureAdjust the Z-axis position of the corresponding release input signal errorLE3A1 The thread trimming driver has issued abnormalCheck the thread trimming drive card and/or the joint -21 trimming output time exceededCheck/replace joint card3A6 Incorrect ATH movable knife retract positionCheck the position of the ATH movable knife3A8A thread holding driver Error signal is thread holding inverter LED.