Clamp Assemblies
Found 8 free book(s)INSTALLATION INSTRUCTIONS HUSTLER 4-BTV, 5-BTV TRAP ...
new-tronics.com9. Install the 10 meter trap to the 1-1/4" x 72" tube, using one of the clamp assemblies. Set to dimension A and table in Figure 7, the measurement should be made at the end of the long tube and the bottom edge of the trap. Securely and carefully tighten the clamp. IMPORTANT THE PLASTIC CAP IS THE TOP OF THE TRAP AND MUST BE INSTALLED IN THAT
Kreg Jig K4 / Kreg Jig K4 Master System Owner’s Manual
www.kregtool.comWith the pocket holes drilled, position and clamp your parts. Small flat assemblies can be aligned by clamping them to a flat surface. When using a Kreg face clamp to clamp large flat assemblies off the edge of your work surface, position the large clamp pad on the side of the joint opposite the pocket holes.
5040/5050/5060/5065 AX/EX Rim Clamp Tire Changer
www.mcgeecompany.comRim Clamp® Tire Changer For servicing single piece automotive and most light truck tire/wheel assemblies * 5050, 5060 & 5065 Models Shown. Parts Identification The following pages include parts breakdowns with exploded view illustrations to help with ordering replacement or spare kits. Assemblies are noted where
Rosemount 0085 Pipe Clamp Sensor - Emerson Electric
www.emerson.comRosemount X-well assemblies are available in most Rosemount 0085 Pipe Clamp sensor diameter sizes. Typical model number of the assembly: Rosemount 3144P and 0085 3144P D 1A 1 NA M5 PT C1 HR7 XA 0085 N 3 P1 J 0080 C 0169 N XA Rosemount 648 Wireless and 0085 648 D X 1 D NA WA3 WK1 M5 PT C1 XA. September 2021. Rosemount 0085 Pipe Clamp …
50/60/70/90 and X-Model Series Rim Clamp Tire Changers
www.coatsgarage.comRim Clamp® Tire Changers For servicing single piece automotive and most tubeless light truck tire/wheel assemblies. Any other type, including tube type and agricultrual, require special handling. Tires identified as truck tires need to adhere to OSHA standard 1910.177.
50/60/70/80/90 X-Model Series - Coats
www.coatsgarage.comRim Clamp® Tire Changers For servicing single piece automotive and most tubeless light truck tire/wheel assemblies. Any other type, including tube type agricultrual, require special handling. Tires identifi ed as truck tires need to adhere to OSHA standard 1910.177.
Quick Start Guide: Rosemount™ DP Level Transmitters and ...
www.emerson.comClamp style tank spud For clamp style tank spud seals the procedures for welding the tank spud to the tank vessel are shipped with the tank spud. For the welding procedure refer to Rosemount DP Level Transmitters and 1199 Diaphragm Seal Systems Reference Manual for proper welding tank spud guidelines. The clamp and gasket are furnished by the user.
TOLCO seismic bracing - Eaton
www.eaton.comClamp™ sway brace attachments • Secured to wall using two Fig. 980 universal swivel sway brace . attachments • 1" (or up to 2") schedule 40 brace pipe. Four way “top of riser” seismic brace assembly . NFPA 13 (2013) Sec. 9.3.5.8.1 “Tops of risers exceeding 3 feet (1m) in length shall be provided with a four way brace.” * Lateral ...