Fittings Threaded Fittings
Found 9 free book(s)
23 22 13 Steam and Steam Condensate Piping (072913)
www.uh.eduAll pipe and fittings shall be manufactured by a domestic company. 3. All brass and bronze piping components shall have no more than 15 percent zinc content. E. Threaded Fittings: 1. All threaded fittings shall be USA factory made wrought carbon or alloy steel threaded fittings conforming to ASTM A234 or malleable iron threaded fittings ...
Pipe Fittings & Steel Nipples
www.pipe-valve-fitting.comThreaded Fittings Class 150 (Standard) Class 300 (XS/XH) UÊ >ÃÌÊ À Ê* «iÊ ÌÌ }à Threaded Fittings Class 125 (Standard) Class 250 (Extra Heavy) Flanged Fittings Class 125 (Standard) Class 250 (Extra Heavy) Drainage Fittings UÊ- > Ê-Ìii Ê ÌÌ }Ã Ê iÀV > ÌÊ-Ìii UÊ* «iÊ «« ià Seamless and Welded UÊ* «iÊ
Ward Manufacturing PiPe fittings catalog
www.wardmfg.comAug 01, 2014 · straightness to allow them to easily engage threaded pipe. In addition, Ward fittings have a chamfered opening to allow faster and easier pipe engagement. This feature also protects the fitting threads from damage during handling. All Ward black & galvanized Class 150 Malleable Iron Fittings
TRAP PRIMERS, TRAP PRIMER ADAPTERS, DISTRIBUTION …
www.jrsmith.comTHREADED CONNECTIONS FIGURE NO. 281-T 3/4” X 1 1/2” NPT THREADED CONNECTIONS FIGURE NO. 281-S 3/4” X 1 1/2” SWEAT CONNECTIONS AIR GAP FITTINGS AIR GAP FITTINGS FEATURES: n Required by code for protection against backflow into the potable water system n Optional finish is nickel plated brass An air gap is a vertical break …
STANDARDS & SPECIFICATIONS Dimensions of Spiral Barb …
www.spearsmfg.comDO NOT use oil or detergent on any fittings. Use plain water or soapy water as lubricant on fitting. For attachment to previously installed metallic systems or threaded fixtures, the insert adapter is utilized. Apply thread sealant to the threaded end of adapter and tighten into female connection. Steel clamp is then slipped over pipe end and pipe
0302 Brass Fittings Catalog
d2cl5to9q9oami.cloudfront.net• To order flare fittings with nuts assembled, add suffix”WN”. Assembly Instructions 1. Cut tubing to required length, making sure that the ends are square and all burrs are removed. 2. Slide nut onto tubing. Threaded end of nut must face out. 3. Flare tubing end with a 45˚ flaring tool. A. Measure flare diameter.
Fittings and Tubing - Autoclave
www.autoclave.comFittings Medium Pressure Fittings - Pressures to 20,000 psi (1379 bar) Parker Autoclave Engineers Medium Pressure fittings, nicknamed “Slimline SF”, are designed for use with SM Series valves and Parker Autoclave Engineers' Medium Pressure tubing. They incorporate coned-and-threaded connections with the orifice sized to match the high-flow
Valve Fittings and Wellhead Components
www.parker.comfittings is for dynamic systems. A vast majority of systems where our fittings are used fall in this category. Most PGI business unit grease fittings are rated for 350 °F (176 °C). For systems with higher temperature requirements or sub-sea low temperature applications, consult …
Medium- and High-Pressure Fittings, Tubing, Valves, and ...
www.swagelok.comMedium- and High-Pressure Fittings, Tubing, Valves, and Accessories 1 MEDIUM- AND HIGH-PRESSURE www.swagelok.com Medium- and High-Pressure Fittings, Tubing, Valves, and Accessories Rated up to 60 000 psig (4134 bar) End connections up to 1 1/2 in. and 12 mm NACE® MR0175/ISO15156 compliance available