Flanges for use with
Found 14 free book(s)
PIPING MATERIAL CLASS DESCRIPTION
fortress.wa.govFlat faced flanges shall be used to match flat face equipment and other flat faced flanged components (e.g., copper alloy, cast iron flanges, GRP flanges and for NPS 30 and larger flanges in large diameter water lines). Orifice flanges shall be in accordance with ASME B16.36 and shall be supplied in pairs, complete with
PVC & CPVC INJECTION MOLDED CLASS 150 FLANGES
www.spearsmfg.comSpecified minimum bolt lengths are based on the use of two Spears® Flanges, two standard flat washers, standard nut and 1/8" thick elastomer full face gasket. Mating with other brands or accessories may require variation. Bolts and gaskets are not supplied with flanges. Dimension references: L = Overall length of hub, ± 1/16 inch.
NORME EUROPÉENNE 1092-1 EN DAAD STAN EUROPEAN
www.htcflange.comspecified in the ISO standard for use with the ANSI/ASME based flanges; 4) This standard gives an informative annex concerning requirements of EU Directives. 1 Scope This European Standard for a single series of flanges specïfies requirements for circular steel flanges in PN designations PN 2.5 to PN 100 and nominal sizes from DN 10 to DN 4000.
PIPING PRODUCTS - Prochem
www.prochem.com.aualong with blind flanges. Other standards in less common use or that may appear on old specifications include: BS 1560 Section 3.1 – Circular Flanges for Pipes, Valves and Fittings (class designated). This has been now superseded by EN 1759-1. BS 4504-3.1 – Circular flanges for pipes, valves and fittings (PN designated).
API FLANGES - Keddco
keddco.comFlanges are available as Weld Neck, Integral, Blinds, Target & Test Blinds for use with the following pressure ratings:-MAX. WORKING PRESSURE TEST PRESSURE PRODUCT SPECIFICATION LEVELS API TEMPERATURE RATING MIN. YIELD MN. TENSILE MATERIAL MIN. YIELD MIN. TENSILE MATERIAL 2,000 PSI 3,000 PSI 1,2,3 K (-60 DEG C) TO Y (+345 DEG C)
SAFE USE OF GRINDERS OHS-PROC-125 - Stanwell
www.stanwell.com- Always use undamaged disc flanges that are of correct size and shape for your selected disc. Proper disc flanges support the disc thus reducing the possibility of breakage. Flanges for cut-off discs may be different from grinding disc flanges. - Do not use worn down discs from larger power tools. A disc intended for a
Pipe Flanges and Flanged Fittings
www.abangah-co.completed in March 1937), 1,500-lb flanges in the 14-in. through 24-in. range, 2,500-lb flanges and flanged fittings in the 1 ⁄ 2 -in. through 12-in. range, and dimensions for a full line of ring joint
Dimensions for Class 300 Flanges - Thermometrics Corp
thermometricscorp.comsteel flanges mechanical properties and chemistry conform to ASTM A105. Flanges are furnished faced, drilled and spot faced or back faced. *1/16 in. raised face included in dimensions Q, Y and YY. **Bolt hole diameter 1/8 in. larger than bolt diameter. ***Weights listed are approximate values. **** To be specified by the customer. Flange Weight ...
BOLT & STUD DIMENSIONS FOR ANSI FLANGES
www.rhinofitt.co.ukCARBON STEEL PIPE FLANGES TO ANSI B16.5 (BS 1560) FORGINGS TO ASTM A105 - Not recommended for prolonged use above 427qC FORGINGS TO ASTM A350 - LF2 - Not to be used above 343qC-29 to 38 50 100 150 200 250 300 350 375 400 425 450 475 500 525 540 FLANGE ABOVE DN 600 ARE NOT INCLUDED IN ANSI B16.5 AND THE CLASS DESIGNATIONS
VEHICLE SPECIFICATIONS - USPS
about.usps.comflanges. Fastening shall be welding, riveting, bolting, or equivalent. Welding will be at least 1.5 inches long on both top and bottom flanges. Riveting or other fastening will use at least 4 fasteners at each vertical post. On new vehicles, horizontal retainer rails shall be installed before installation of the interior
IS 6392 (1971): Steel pipe flanges
law.resource.org1.2 Thisstandarddoes not specify limitations on the use ofvarious methods ofattachment of flanges to pipe or other equipment. The adequacy for operating conditions of any method of attachment specified should be determined by the designer ofthe piping or equipment. 1.3 The types and materials ofgaskets used shall be agreed between the
CROSS-REFERENCE OF ASTM MATERIAL SPECIFICATIONS …
globalsupplyline.com.auCOVERING CAST/FORGED VALVES, FITTINGS, FLANGES & PIPE ~ Short lead time manufacturer, supplying world wide ~ For technical references and ASTM/ ASME cross reference information on stainless, duplex, chrome-moly and alloy steel used in valves & piping systems in the petrochemical and refining industries, go to the technical section of our website.
Pressure Vessel Engineering Ltd. provides: ASME Vessel ...
www.pveng.com2) use weaker bolts - same idea as above. 3) if material waste and cost are no object, make the flange thicker. This route often is used when a custom appendix 2 flange must mate up to standard flanges such as B16.5 series which seldom calculate to appendix 2 rules.
Roof Curb
www.trane.comroof support members. Use tack welding or other suitable fastening method to secure the roof curb in place. The curb can also be mounted on a roof deck. In this case, additional nailing plates must be provided directly below the flanges of the curb to give further support, and to minimize vibration. See Figures 15 and 16. When the installation ...