Programmable Reference
Found 10 free book(s)
TL431 - Programmable Precision References
www.onsemi.comThe 2.5 V reference makes it convenient to obtain a stable reference from 5.0 V logic supplies, and since the TL431A, B operates as a shunt regulator, it can be used as either a positive or negative voltage reference. Features • Programmable Output Voltage to 36 V
Modicon Modbus Protocol Reference Guide
www.modbus.orgProgrammable Controller systems: GM–0984–SYS 984 Programmable Controller Systems Manual. Modicon, Inc. Refer to the following publications for details about the application and installation of the Modbus Plus network and related communications devices: GM–MBPL–001 Modbus Plus Network Planning and Installation Guide. Modicon, Inc.
Sensi Wi-Fi Programmable Thermostat MANUAL …
www.emerson.comConfiguration Menu Items Reference Menu Configurations SensiTM Wi-Fi Programmable Thermostat | MANUAL OPERATION 6 No. Menu Item Default Options AC1 - Conventional Cooling 1 (single stage) AC2 - Conventional conventional A/C systems. Cooling 2 (Two Stage) HP1 - Heat Pump 1 (Single Stage) HP2 - Heat Pump 2 (Two Stage) AC0 - No Cooling
LT3065 Series 45V VIN, 500mA Low Noise, Linear Regulator ...
www.analog.comn Programmable Precision Current Limit: ±10% n Power Good Flag n Low Noise: 25µVRMS (10Hz to 100kHz) n Adjustable Output (VREF = VOUT(MIN) = 600mV) n Output Tolerance: ±2% Over Line, Load and Temperature n Stable with Low ESR, Ceramic Output Capacitors (3.3µF Minimum) n Single Capacitor Soft-Starts Reference and Lowers Output Noise
MagicStat CT3200 Programmable Thermostat - Honeywell
customer.honeywell.comterminals, see the wiring cross reference table on page 10. f. Disconnect the wires from the old thermostat and wrap the wires around a pencil to keep them from falling back into the wall. Note: Remember, if your old thermostat contains mercury, you must recycle it. See page 2 for more recycling information. Check your progress
LTC3895 - 150V Low Iq, Synchronous Step-Down DC/DC …
www.analog.comThe LTC3895 features a precision 0.8V reference and power good output indicator. The output voltage can be programmed between 0.8V to 60V using external resistors ... n Programmable Fixed Frequency (50kHz to 900kHz) n Selectable Continuous, Pulse-Skipping or Low Ripple
SIMATIC S7 S7-1200 Programmable controller
www.allmar.send.plS7-1200 Programmable controller System Manual, 04/2009, A5E02486680-01 3 Preface Purpose of the manual The S7-1200 series is a line of programmable logic controllers (PLCs) that can control a variety of automation applications. Compact design, low cost, and a …
LS1203 Product Reference Guide - Zebra Technologies
www.zebra.comThe LS1203 Product Reference Guide provides general instructions for setting up, operating, maintaining, and troubleshooting the LS1203 scanner. Configurations This guide includes the following configurations: • LS1203-SR - Standard range scanning • LS1203-HD - High density scanning Chapter Descriptions Topics covered in this guide are as ...
U-Boot Quick Reference - NXP
www.nxp.comU-Boot Quick Reference, Rev. 0 Freescale Semiconductor 3 4 List of Commands 4.1 AUTOSCR Run script from memory: autoscr [addr] - run script starting at addr - A valid autoscr header must be present The autoscr command allows “shell” scripts to run under U-Boot. To create a U-Boot script image, commands are written to a text file.
18-Bit - Multi-Channel Delta-Sigma Analog-to-Digital ...
ww1.microchip.comMar 26, 2009 · The on-board 2.048V reference voltage enables an input range of ± 2.048V differentially (full scale range = 4.096V/PGA). These devices can output analog-to-digital conversion results at rates of 3.75, 15, 60, or 240 samples per second depending on the user controllable configuration bit settings using the two-wire I2C serial interface.