Resistor Marking Surface Mount Resistor Marking
Found 9 free book(s)
Wirewound Resistors, Precision Power, Surface Mount
www.vishay.com(1) Flame retardance test may not be applicable to some resistor technologies Notes • Part marking: 1/2 W - DALE, value; 1 W - model, value, tolerance, date code; 2 W and 3 W - DALE, model, value, tolerance, date code (1) As of 1/1/2010, the WSC0001 and WSC0002 are molded with thermopl astic in lieu of epoxy. Reference PCN-DR-002-2009 and PCN ...
LT3080 - Adjustable 1.1A Single Resistor Low Dropout …
www.analog.comResistor Low Dropout Regulator The LT ®3080 is a 1.1A low dropout linear regulator that can be paralleled to increase output current or spread heat in surface mounted boards. Architected as a precision cur-rent source and voltage follower allows this new regulator to be used in many applications requiring high current,
SF-1206S Series - Slow Blow Surface Mount Fuses
www.farnell.comn Slow blow thin film chip fuse for overcurrent protection n 3216 (EIA 1206) miniature footprint n Surface mount packaging for automated assembly n UL listed (UL 248-14) n RoHS compliant* and halogen free** Electrical Characteristics SF-1206S Series - Slow Blow Surface Mount Fuses *** Resistance value measured with less than 10 % of rated current.
Power Metal Strip Resistors, Low Value (Down to 0.0005 Ω ...
www.vishay.com(1) Flame retardance test may not be applicable to some resistor technologies Notes • Part marking: value; tolerance: due to resistor size limitations some resistors will be marked with only the resistance value (1) For values above 0.1 Ω derate linearly to 80 % rated power at 0.5
ELECTRONICS INDUSTRIES Generic Requirements for Surface ...
www.ipc.orgSurface Mount Design and Land Pattern Standard Developed by the Surface Mount Land Patterns Subcommittee (1-13) of the Printed Board Design Committee (1-10) of IPC Users of this publication are encouraged to participate in the development of future revisions. Contact: IPC 3000 Lakeside Drive, Suite 309S Bannockburn, Illinois 60015-1219 Tel 847 ...
LM2596 - 3.0 A, Step-Down Switching Regulator
www.onsemi.comD2PAK surface mount package. The other features include a guaranteed 4% tolerance on output voltage within specified input voltages and output load conditions, and 15% on the oscillator frequency. External shutdown is included, featuring 80 …
SA602A Double-balanced mixer and oscillator
www.nxp.comA 22 k resistor from OSC_E (pin 7) to ground increases the DC bias current of the oscillator transistor. This improves the AC operating characteristic of the transistor and should help the oscillator to start. A 22 k resistor does not upset the other DC biasing internal to the device, but smaller resistance values should be avoided. a.
XLSEMI Datasheet
www.nikom.bizPart Number Marking ID Lead Free Lead Free Packing Type XL6009E1 XL6009E1 Tube Package Temperature Range XL6009TRE1 XL6009E1 Tape & Reel XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant. Absolute Maximum Ratings（Note1） Parameter Symbol Value Unit Input Voltage Vin -0.3 to 42 V
INSTALLATION INSTRUCTIONS PUSH BUTTON START SYSTEM
www.jegs.comrelays do not use internal diode or resistor snubbers. FOR ALL RELAYS: Pins 30 and 86 are connected to B+, 12VDC. Pin 85 is pulled low by the system to power the coil; pin 87 is the high current output which is enabled when the coil is powered. Pin 87A is not used. Form C Relay Relay Pinouts 2.