Resistors resistors
Found 10 free book(s)How to Choose Replacement Capacitors and Resistors when …
www.condoraudio.comHow to Choose Replacement Resistors when repairing and restoring high-quality stereo equipment In the old days, the only resistors available were carbon-type. By now, many of these in the power section are way out-of-spec, and need to be replaced. Also, carbon resistors are generally very noisy, so although the original carbon resistors in the
MP900 and MP9000 Series Kool-Pak Power Film Resistors TO ...
www.caddock.comresistors are packaged in plastic shipping tubes, 50 pieces per tube. These resistors are available in a 50 piece minimum quantity and in full tube quantity increments (i.e. 50, 100, 150, etc.). The MP9100 resistors are packaged in plastic shipping tubes, 25 pieces per tube. New Power Resistor with Exposed Ceramic Heat Dissipating Mounting Surface.
Experiment 4 ~ Resistors in Series & Parallel
www.umsl.eduResistors (R1 = 2.2 kΩ, R2 = 6.8 kΩ, and R3 = 4.7 kΩ), multimeter, and DC power supply. Theory: In the first part of this experiment we will study the properties of resistors, which are connected “in series”. Figure 1 shows two resistors connected in …
Type MG Precision High Voltage Resistors - Caddock
www.caddock.comResistors' outstanding combination of performance features: • Resistance Tolerances from ±1% to ±0.1%. • Temperature Coefficient, for standard resistance range, of 80 ppm/°C, with resistance tolerances as tight as ±0.1%. • Type MG resistors have demonstrated stability of 0.01% per 1,000 hours in extended load life testing of standard
`Ohm’s Law III -- Resistors in Series and Parallel
www.phys.utk.eduResistors are manufactured in many different materials, forms, shapes, values, power ratings, and tolerances. While some resistor values are labeled with text, common resistors are color coded with bands to indicate their ohmic values. The color-numeric key is given in Table 1. The first colored band represents the first digit of the value
Introduction: The Nature of VCRs - Vishay Intertechnology
www.vishay.comResistors R2 and R3 in Figure 6 couple the drain signal to the gate; the resistor values are equal, so that symmetrical voltage-current characteristics are produced in both quadrants. The resistors must be sufficiently large to provide minimum loading to the circuit: R 2 = R 3 10 [R 1 rDS (max) R L] (3) Typically, 470-k resistors will work well ...
STANDARD VALUE DECADE FOR 1% RESISTORS
www.brannonelectronics.comstandard value decade for 1% resistors ohms* 10.0 14.7 21.5 31.6 46.4 68.1 10.2 15.0 22.1 32.4 47.5 69.8 10.5 15.4 22.6 33.2 48.7 71.5
Thick Film Chip Resistors - ROYALOHM
www.royalohm.comThick Film Chip Resistors • For 01005, 0201, 0402 size, no marking on the body due to the small size of the resistor. • ±5% tolerance product: the marking is 3 digits, the first 2 digits are the significant of the resistance and the 3rd digit denotes number of zeros following.
Resistors & Circuits - Learn About Electronics
www.learnabout-electronics.orgResistors are available in several different versions of ‘Preferred Values’ as explained in Resistors & Circuits Module 2.2. Some of these versions contain a wider range of values, requiring a more accurate numerical value and closer tolerance ratings than can be achieved in the four band colour code. ...
MCP23017/MCP23S17 Data Sheet - Microchip Technology
ww1.microchip.comMCP23017/MCP23S17 DS20001952C-page 6 2005-2016 Microchip Technology Inc. FIGURE 1-3: I2C BUS START/STOP BITS TIMING FIGURE 1-4: I2C BUS DATA TIMING TABLE 1-3: I2C BUS DATA REQUIREMENTS I2C Interface AC Characteristics: Unless otherwise noted, 1.8V VDD 5.5V at -40 C TA +125 C, RPU (SCL, SDA) = 1 k , CL (SCL, SDA) = 135 pF Param. No.