Standard System Standard Fittings
Found 8 free book(s)SPECIFICATIONS FOR SPIRAL PIPE AND FITTINGS
www.smcduct.comAll fittings can be manufactured with: • Complete Seal Spiral Pipe System – 6” to 24” Diameter (even sizes) • E-Z Flange Jr. with Barrel Clamp – 6” to 24” Diameter • E-Z Flange with Barrel Clamp – 26” to 96” Diameter • Standard Spiral Pipe End • Companion Angle Ring Elbow Lock Seam Riveted Lap Seam Standing Seam
TECHNICAL INFORMATION WEIGHTS & DIMENSIONS
www.spearsmfg.comto ANSI/NSF ® Standard 61, Annex G and is in compliance with California’s Health & Safety Code Section 116825 (commonly known as AB1953) and Vermont Act 193. Weighted average lead content <=0.25%. Spears® PVC and CPVC Pipe, Fittings and Valves have always been lead-free and Certified by NSF International for use in potable water systems.
Push-in Y-fitting QSYL Push-in fittings QS, standard Push ...
www.festo.comPush-in fittings QS, standard Key features Push-in fittings product range QSM, mini Datasheets a Internet: qsm QS, standard Internet: qs Miniature push-in fittings for maxi-mum component density in confined spaces. For pneumatic applications with a temperature range up to 80°C and a pressure range up to 14 bar. Tubing O.D. 2, 3, 4 and 6 mm ...
Metric Fittings & Valves PVC & CPVC Metric Fittings ...
www.spearsmfg.comMetric Fittings & Valves PVC & CPVC Metric Fittings, Unions & Valves SCHEDULE 40 & SCHEDULE 80 PIPE DIMENSIONS ASTM STANDARD D 1785 Nominal Pipe Size (inch) Mean Outside Diameter (inch) O.D. Tolerance (inch) Minimum Wall Thickness (inch) Schedule 40 Schedule 80 1/2 0.840 ± 0.004 0.109 0.147 3/4 1.050 ± 0.004 0.113 0.154 11.315 ±0.005 0.133 0.179
Metric Hydraulic Compression Tube Fittings
www.williamsfluidair.comThese metric fittings are based on the bite-type system. The fittings have a trumpet shaped opening (24E taper). This taper opening acts as a wedge together with the cutting ring which will, with pressure from the rotation of the nut, be forced to cut into the tube and form a visible collar. This system will
CPVC CTS FITTINGS & VALVES - spearsmfg.com
www.spearsmfg.com(hydrostatic testing), the system must be slowly filled with water and the air bled from the highest and furthest points in the system before test pressure is applied. Failure to do so can cause damage to the piping system and could be harmful to the job site personnel should a failure occur. If a leak is found, the affected product must be cut and
STANDARD SPECIFICATION FOR HUBLESS CAST IRON SOIL …
www.cispi.orgFittings of the pat-terns specified within this standard shall conform to the applicable dimensions in Tables 5-105, inclusive. Fittings not listed shall conform to Table 1 for wall thickness and dimension R for the minimum radius of any drain inlets that any such fittings provide. ♦ 7.2.2 Ends of Fittings—Ends of fittings shall
Fittings and Accessories - Prime Conduit
www.primeconduit.comSee the P&C Duct Fittings (DB & EB) section for couplings. 23240 Chagrin BlvdSuite 405 • Cleveland, OH 44122 • 216-464-3400 • www.primeconduit.com 8