09 National Toilet Partitions-Hardware e - natpart.com

1 Page 1 of 5 NTPN ational ToiletPartitions Toilet PARTITION hardware No matter what material you select for your partitions , the final product is only as good as the hardware . With excellent hardware , partitions will last for a lifetime. With lesser hardware , your partitions are subject to breakage. National Toilet partitions provides a variety of hardware to meet your needs. You can make certain this hardware is included in your partition by using the specifications provided. You can count on the hardware from National Toilet partitions . HINGES DOOR hardware BRACKETS 1. 14 Gauge ST/ST 1. Chrome Plated Zamac 1. Single High Aluminum 2. 11 Gauge ST/ST 2. 14 Gauge ST/ST 2. Double High Aluminum 3. Full High Aluminum 3. cast ST/ST 3. Full High Aluminum 4. Full High ST/ST 4. Aluminum 4. Single High ST/ST 5. Integral Hinge 5. Zamac w/thumb turn latch 5. Full High ST/ST 6. Wrap Around Aluminum 6. 14 Gauge ST/ST w/thumb turn latch 6. cast ST/ST 7.

2 cast ST/ST w/thumb turn latch 7. Full High Plastic 8. Chrome Plated Zamac Page 2 of 5 Phenolic partitions hardware 14-gauge Surface Mounted Stainless Steel Hinge 14-gauge Stainless Steel Hinge. Hinge shall be cast of Type 302/304 Stainless Steel and shall have a Satin finish. Hinge shall be gravity type for self-closing action and shall be fully adjustable up to 360 degrees. Pivot pin shall be made of Type 302/304 Stainless Steel. Only Stainless Steel components shall be used in the construction of the Hinge. Plastic inserts are unacceptable. Hinges shall provide emergency access by lifting the door. Hinges shall be pre-drilled for mounting to door and pilaster with Stainless Steel Through-Bolts. 14-gauge Stainless Steel Door hardware Strike and Keeper: Heavy Duty 14 Gauge Stainless Steel with a Satin finish. The Strike and Keeper shall be high, with the mounting holes at The Strike and Keeper shall have an integral rubber bumper door stop.

3 Slide Latch: Heavy Duty 14 Gauge Stainless Steel with a Satin finish. The Slide Latch shall be surface mounted. The slide bar shall be 1 wide and 3 long. Latch shall have an internal Stainless Steel buffering spring to prevent damage when door is inadvertently slammed against the Latch. Mounting holes are to be spaced at Latch knob is to be riveted to the slide bar and then welded to insure that the knob will not come off. Coat Hook: Heavy Duty cast Stainless Steel with a Satin finish. Coat Hook and Bumper shall be high, wide and shall protrude out from the door . The hook portion shall have a finished diameter of .250 . Door Stop: Heavy Duty 14 Gauge Stainless Steel with a Satin finish. Plated Zamac Door Stops are unacceptable. Door Stop shall have a x base and shall protrude from the wall. The bumper at the end of the Door Stop shall be .250 thick. The diameter of the shaft shall be .270 . Pull Handle: Heavy Duty 14 Gauge Stainless Steel with a Satin finish.

4 Plated Zamac Door Pulls are unacceptable. Pull Handle shall protrude from the face of the door and shall be long. The Pull Handle shall have mounting holes drilled at The Pull Handle shall be .655 wide. Double-high Aluminum Double High ( ) Extruded 6063-T5 Aluminum with a Satin Anodized finish. The minimum weight shall be pounds per lineal foot. All holes for mounting to wall and panel/pilaster shall be pre-drilled. There shall be four (4) holes for mounting to the wall and two holes for mounting to panel/pilaster. Each Bracket is to have a minimum wall thickness of .125 . Page 3 of 5 Solid Plastic partitions hardware Aluminum Wrap Around Hinge Aluminum Wrap Around Hinges shall be high and shall wrap around the edge of the Pilaster and Door and shall be made of Extruded 6063-T5 Aluminum with an Anodized finish. Hinges shall be fully adjustable up to 360 degrees. Pivot pin shall be nylon with a .250 diameter Stainless Steel reinforcing pin.

5 Hinges shall provide emergency access by lifting the door. Hinges shall be pre-drilled for mounting to door and pilaster with Stainless Steel Through-Bolts. Aluminum Door hardware Strike and Keeper: Heavy Duty Extruded Aluminum with an Anodized Finish. The Strike and Keeper shall be high, with three mounting holes and the wall thickness shall be a minimum of .125 . The Strike and Keeper shall have an integral rubber bumper door stop. Slide Latch: Heavy Duty Extruded Aluminum with an Anodized Finish. The Slide Latch shall be surface mounted. The slide bar shall be .250 thick, .95 wide and long. Latch shall have an internal buffering spring to prevent damage when door is inadvertently slammed against the Latch. Mounting holes are to be spaced at Latch knob is to be pressed and then riveted to the slide bar to insure that the knob will not come off. Coat Hook: Heavy Duty Chrome Plated Zamac. Coat Hook and Bumper shall be high, wide and shall protrude out from the door.

6 The hook portion shall have a finished diameter of .250 . Door Stop: Heavy Duty Chrome Plated Zamac. Door Stop shall have a base diameter and shall protrude from the wall. The bumper at the end of the Door Stop shall be .250 thick. The diameter of the shaft shall be .6875 . Pull Handle: Heavy Duty Chrome Plated Zamac. Pull Handle shall protrude from the face of the door .940 and shall be long. The Pull Handle shall have mounting holes drilled and tapped for 10/24 threads at The Pull Handle shall be .655 wide and shall be mounted back to back with the Slide Latch. Double-high Aluminum Double High ( ) Extruded 6063-T5 Aluminum with a Satin Anodized finish. The minimum weight shall be pounds per lineal foot. Inside of opening of Bracket shall be for panels and for pilasters. All holes for mounting to wall and panel/pilaster shall be pre-drilled. There shall be four (4) holes for mounting to the wall and two holes for mounting to panel/pilaster.

7 Each Bracket is to have a minimum wall thickness of .125 . Page 4 of 5 Plastic Laminate partitions hardware Zamac Hinges Zamac Hinges shall be recessed heavy duty, non-handed, chrome plated zamac with gravity self-closing action. Mounting holes at and the wall thickness shall be a minimum of .125 Zamac Door hardware Strike and Keeper: Heavy Duty Chrome Plated Zinc Die cast . The Strike and Keeper shall be high, with the mounting holes at , and the wall thickness shall be a minimum of .125 . The Strike and Keeper shall have an integral rubber bumper door stop. Slide Latch: Heavy Duty Chrome Plated Zinc Die cast . The Slide Latch shall be surface mounted. The slide bar shall be .150 thick, wide and long. Latch shall have an internal Stainless Steel buffering spring to prevent damage when door is inadvertently slammed against the Latch. Mounting holes are to be spaced at Latch knob is to be riveted to the slide bar and then welded to insure that the knob will not come off.

8 Coat Hook: Heavy Duty Chrome Plated Zinc Die cast . Coat Hook and Bumper shall be high, wide and shall protrude out from the door . The hook portion shall have a finished diameter of .250 . The stock number shall be molded into the back of the Coat Hook and Bumper for ease in identification. Door Stop: Heavy Duty Chrome Plated Zinc Die cast . Door Stop shall have a base diameter and shall protrude from the wall. The bumper at the end of the Door Stop shall be .250 thick. The diameter of the shaft shall be .6875 . The stock number shall be molded into the back of the Door Stop for ease in identification. Pull Handle: Heavy Duty Chrome Plated Zinc Die cast . Pull Handle shall protrude from the face of the door .940 and shall be long. The Pull Handle shall have mounting holes drilled and tapped for 10/24 threads at The Pull Handle shall be .655 wide and shall be mounted back to back with the Slide Latch. Single-high Zamac All Brackets shall be made of Chrome Plated Zamac.

9 All holes for mounting to wall and panel/pilaster shall be pre-drilled. Each Bracket is to have a minimum wall thickness of .125 . Page 5 of 5 Other Polymer Shoes Shall be one piece construction made of injection molded HDPE plastic. Shoes shall be available in ten (10) standard colors to coordinate with Pilaster color. Stainless Steel Shoe & Heel ASTM A 167, Type 302/304 Stainless Steel, minimum 3 high, 18-gauge, finished with #3 Directional Polish, attached with Stainless Steel Through Bolts. Fasteners For Phenolic and Solid Plastic all Fasteners shall be Stainless Steel with theft proof heads, Through-Bolted unless noted otherwise. No chrome plated steel or brass will be acceptable. For Plastic Laminate Chrome Plated Steel will be used. Overhead Bracing Continuous Heavy Duty Extruded 6063-T5 Aluminum Headrail with Anti-Grip profile. Headrail shall have integral reinforcing channel and curtain track. Headrail shall have a Satin Anodized finish.

10 Provide Headrail Corner Brackets, Wall Brackets, and Headrail End Caps as required. The Headrail and Headrail Brackets shall have a minimum wall height of 2 . The minimum wall thickness of the Headrail and Headrail Brackets shall be .125.