1305 Adjustable Frequency AC Drive - Rockwell Automation

1 User Manual1305 Adjustable Frequency AC Drive (Series C) kW ( Hp), Firmware and UpImportant User InformationRead this document and the documents listed in the Additional Resources section about installation, configuration, and operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be no event will Rockwell Automation , Inc.

2 Be responsible or liable for indirect or consequential damages resulting from the use or application of this examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation , Inc. cannot assume responsibility or liability for actual use based on the examples and patent liability is assumed by Rockwell Automation , Inc. with respect to use of information, circuits, equipment, or software described in this of the contents of this manual, in whole or in part, without written permission of Rockwell Automation , Inc., is this manual, when necessary, we use notes to make you aware of safety may also be on or inside the equipment to provide specific : Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic : Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss.

3 Attentions help you identify a hazard, avoid a hazard, and recognize the information that is critical for successful application and understanding of the HAZARD: Labels may be on or inside the equipment, for example , a Drive or motor, to alert people that dangerous voltage may be HAZARD: Labels may be on or inside the equipment, for example , a Drive or motor, to alert people that surfaces may reach dangerous FLASH HAZARD: Labels may be on or inside the equipment, for example , a motor control center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE). Rockwell Automation Publication - June 2013 Document UpdateElectronic Motor Overload ProtectionThis product does not offer speed-sensitive overload protection, thermal memory retention or provisions to act upon motor over-temperature sensing in motors.

4 If such protection is needed in the end-use product, it needs to be provided by additional Automation Publication - June 2013 Notes: Rockwell Automation Publication - June 2013 Summary of ChangesThe information below summarizes the changes to the 1305 User Manual, publication since the last of New or Updated InformationPageAdded the document update concerning Electronic Motor Overload of manualRockwell Automation Publication - June 2013 Notes:Table of ContentsChapter 1 Information and PrecautionsChapter Objectives1-1.. Manual Objectives1-1.. Receiving, Unpacking, Inspection, Storing 1-2.. General Precautions1-2.. Conventions Used In This Manual1-3.. Nameplate Location1-4.. Firmware Compatibility1-4.. Catalog Number Code Explanation1-5.. Chapter 2 Installation/WiringChapter Objectives2-1.. Terminal Block Access2-3.

5 Input Devices2-5.. Input Power Conditioning2-6.. Input Fusing2-6.. Electrical Interference EMI/RFI2-7.. RFI Filtering2-8.. CE Conformity2-8.. Grounding2-9.. Power Wiring2-11.. Drive Operation without a Human Interface Module (HIM)2-17.. control Wiring2-17.. Output Devices2-22.. Cable Termination2-22.. Adapters2-23.. Chapter 3 Human Interface ModuleChapter Objectives3-1.. HIM Description3-1.. HIM Operation3-1.. HIM Removal and Installation3-4.. HIM Modes3-5.. Program and Display Modes3-7.. Process Mode3-10.. EEprom Mode3-11.. Search Mode3-14.. control Status Mode3-15.. Password Mode3-17.. Chapter 4 Start UpChapter Objectives4-1.. Start-up Procedure4-1.. Chapter 5 ProgrammingChapter Objectives5-1.. Chapter Conventions5-1.. Function Index5-1.. Parameter Flow Chart5-1.. Programming Example5-4.. Metering5-5.. Set Up5-8.

6 Advanced Setup5-15.. Table of Contents iiFrequency Set5-25.. Feature Select5-32.. Output Configuration5-37.. Faults5-39.. Diagnostics5-42.. Masks5-47.. Owners5-50.. Adapter I/O5-54.. Process Display5-55.. Linear List5-56.. Chapter 6 Toubleshooting and Fault InformationChapter Objectives6-1.. Fault Information6-1.. Appendix A Block Diagram And SpecificationsAppendix B Serial CommunicationsAppendix C Drive AccessoriesAppendix D CE ConformityInformation and PrecautionsChapter1 CHAPTER OBJECTIVESC hapter 1 provides information on the general intent of thismanual, gives an overall description of the Bulletin 1305 Adjustable Frequency AC Drive (herein called the Drive ) andprovides a listing of key Drive options. Additionally, thischapter provides information on receiving and handling OBJECTIVESThe purpose of this manual is to provide the user with thenecessary information to install, program, start up and maintainthe Bulletin 1305 Drive .

7 To assure successful installation andoperation, the material presented must be thoroughly read andunderstood before proceeding. Particular attention must bedirected to the ATTENTION and Important statementscontained 2 provides instructions on how to mount and wire thedrive. It also describes how to operate the Drive without a Hu-man Interface Module. Read the Motor Cable Length sectionon pages 2-13 2-16, and the contact closure inputs informa-tion in the control Terminal Block descriptions on pages 2-19 3 defines the display and control panel keys on theoptional Human Interface Module. A flowchart is provided toguide the user through the key strokes of the various 4 describes the steps to start up the Drive . It includesa typical start up routine defining the adjustments and checks toassure proper 5 outlines the parameter information of the Drive suchas description, number, type, units, factory default, minimumand maximum 6 defines the various Drive faults and the appropriateaction to take as well as general troubleshooting A contains a block diagram and general specifica-tions of the B provides the necessary information for Drive set upusing a PLCR, SLC or other logic controller.

8 A table isprovided that lists each parameter by parameter group withspace for the user to record any custom parameter C lists the accessories and their catalog D lists requirements for CE A comprehensive index is provided to assist the user inlocating specific information. All parameters and fault in-formation are listed alphabetically under parameters and is a registered trademark of Allen-Bradley is a trademark of Allen-Bradley and Precautions1-2 Receiving It is the responsibility of the user to thoroughlyinspect the equipment before accepting the shipment from thefreight company. Check the item(s) received against thepurchase order. If any items are obviously damaged, it is theresponsibility of the user not to accept delivery until the freightagent has noted the damage on the freight bill. Should anyconcealed damage be found during unpacking, it is again theresponsibility of the user to notify the freight agent.

9 Theshipping container must be left intact and the freight agentshould be requested to make a visual inspection of Remove all packing material from within andaround the :Before the installation and start-up of the Drive ,a general inspection of the mechanical integrity ( looseparts, wires, connections, etc.) should be After unpacking, check the item(s) nameplatecatalog number against the purchase order. An explanation ofthe catalog numbering system for the Bulletin 1305 Drive isincluded as an aid for nameplate interpretation. Refer to thefollowing pages for complete The Drive should remain in its shipping containerprior to installation. If the equipment is not to be used for aperiod of time, it must be stored according to the followinginstructions in order to maintain warrranty coverage:DStore in a clean, dry within an ambient temperature range of 40_ to+ within a relative humidity range of 0% to 95%, not store equipment where it could be exposed to acorrosive not store equipment in a construction PRECAUTIONSIn addition to the precautions listed throughout this manual, thefollowing statements which are general to the system must beread and DC Bus Charge Indicator is a neon bulb that will beilluminated when power is applied to the and Precautions1-3 ATTENTION: This Drive contains ESD(Electrostatic Discharge) sensitive parts andassemblies.

10 Static control precautions arerequired when installing, testing, or servicing thisassembly. Component damage may result if ESDcontrol procedures are not followed. If you arenot familiar with static control procedures,reference A-B publication , GuardingAgainst Electrostatic Damage or any otherapplicable ESD protection : An incorrectly applied orinstalled Drive can result in component damage ora reduction in product life. Wiring or applicationerrors, such as, undersizing the motor, incorrect orinadequate AC supply, or excessive ambienttemperatures may result in malfunction of thesystem.!!ATTENTION: Only personnel familiar with thethe Drive and associated machinery should plan orimplement the installation, start-up and subsequentmaintenance of the system. Failure to comply mayresult in personal injury and/or equipment damage.