37° Flared Tube Fittings (SAE J514)

1 37 Flared (SAE J514) Tube Fittings Rev/02/2013 PANAMPANAM PANAM PANAM has been in the field of manufacturing precision Tube Fittings and Instrumentation valves since the last Two decades. With a team of dedicated specialists has always endeavored to satisfy customers ever widening demands with unmatched the latest state of art in-house machinery and infrastructure under one roof, is manufacturing a wide range of Tube Fittings and Instrumentation products in different sizes and metals like brass, stainless steel, monel and in various other metals as per the customer s specific requirements. All Material are to ASTM standards and material test report available upon test report are available from Third Party. Variety of end connections - Male & Female NPT, BSPP, BSPT, ISO tapered pipe ends, Tube / Pipe socket weld. Tube Fittings are 100% factory tested and are NACE certified with Heat code traceability. Maximum working pressure upto 20,000 psig (1378 bar) or Higher available upon request.

2 API ISO 9001:2008 Certified API ISO TS 29001 Certified API Spec Q1 Certified API 6A Certified API 6D Certified API 600 Certified API 602 Certified MFG. Facility Approved by ABS ASTM F1387-99 Leak Test Approved by TUV CE MarkingIntroductionContentsMale ConnectorsSAE 07010204 Female ConnectorsSAE 07010306 UnionsSAE 07010107 Female ElbowSAE 07020313 Swivel Run Tees07043217 Tube PlugsSAE 07011211 Male ElbowsSAE 07020211 Adjustable Male ElbowSAE 0702201245 Male ElbowSAE 07030212 Male Branch TeeSAE 07042514 Adjustable Male Branch TeeSAE 07042915 Male Run TeesSAE 07042415 Female Branch TeesSAE 07042216 Female Run TeesSAE 07042616 Union TeesSAE 07043217 Swivel Branch TeesSAE 070043318 CrossSAE 07050118 Design & ConstructionSAE J51401 Flaring OperationSAE J51402 Ordering InformationSAE J51403 Reducing AdaptersSAE 07012308 SleevesSAE 07011508 Bulkhead UnionsSAE 07060109 Bulkhead Lock NutsSAE 07011509 NutsSAE 07011009 Tube CapsSAE 07010910 Tube Cap AssemblySAE 070112A10 Union ElbowsSAE 07020113 Design & Construction SAE-J514 Assembly InstructionsThe SAE 37 Flared Tube Fittings design is simple.

3 It uses an easily produced flare at the tube end to seal and hold fluid under high pressure. The fitting consists of three pieces: the body, sleeve and nut. The tube end is Flared at a 37 angle(74 included angle) and held between the fitting nose (seat) and the sleeve (support) with the nut as shown in Fig. providing a very effective (single) seal between the fitting nose and the tube design of SAE 37 Flared Tube Fittings is very efficient. The fitting incorporates the smallest seal area of all fitting types. This seal area, as seen in Fig. is only slightly larger than the fluid flow area. The small seal area results in a compact design, low assembly torque, and a relatively high-pressure primary difference between a two-piece flare fitting & the three piece design is the flare support sleeve. The support sleeve provides several key provides a clamping surface for the tube provides a bearing surface for the tube nut. The sleeve isolates the tubefrom the nut, minimizing the tube twist during assembly, a common problem of2-piece flare fitting provides support to the tube flare.

4 The tapered fitting nose tends to wedgeopen the tube flare during assembly. The sleeve helps to resist this expansion,thus eliminating the possibility of tube flare and sleeve jamming inside the eliminates any waste of applied torque and allows for easy makes the fitting adaptable to metric tube merely by changing its on the tube might cause leaks. It is, therefore, important to handle the tube carefully to reduce the risk of leaks. 1. Tubes must not be dragged on the floor. 2. Tubes must not be dragged out of a tubing rack, especially in cases of large OD different methods can be used to cut tubes:- 1. Tube cutter 2. HacksawTo attain a leakfree connection, the tubing must be cut squarely. A good quality tube cutter with the appropriate blade for the tubing material is recommended. Do not try to reduce the time of cutting by taking deep cuts with each turn of the cutter. The end of the tube must be deburred to avoid damage to the fitting and to ensure that the tube reaches the bottom of the order to cut the tube with a hacksaw and to attain square ends, the tube must be cut with guide blocks.

5 This method of cutting requires deburring of the tube not hold the tube in a vise in the place where it will be inserted into the fitting. The vise will leave a mark on the tube that may causeleaks and might cause HANDLINGTUBE CUTTINGTUBE CUTTERHACKSAW the tube to the proper the nut and sleeve onto the a special flaring tool, form theflare to 37 dimension according toSAE the nut onto the body until finger this position, tighten the nut witha wrench 1/4" turn in order to make aleakproof metal-to-metal connectionIn order to ensure maximum fitting reliability and performance, please take great care when selecting the tube for each application. Tubing should be a fully annealed, seamless and drawn, suitable for bending and flaring, according to standardASTM-269, AISI 316 or of finished tubing should be reasonably straight and have smooth ends, free from burrs. Tubing should be free from scale and injurious defects, and it should have a workman like finish.

6 Surface imperfections such as handling marks, die marks, or shallow pits will not be considered injurious defects provided the imperfections are within the tolerances specified for diameter and wall thickness. The removal of such imperfections is not required. (Quality SAE J524).TUBING DATA FOR 37 FLARE THREE-PIECE TUBE ASSEMBLY - QUALITY12 Flaring OperationAllowable Working Pressure Ratings (Capable of 4 to 1 Min Burst)NominalTube Flare DiameterRSinchinchMaxMin3/161/81/45/16 3/8 1/25/83/47/811 1/81 1/4 1 1 according to SAE J533 NominalTube 3/8 1/25/83/47/811 1/41 1/2 2 NominalSAE Dash Size3245681012141620243237 FlareStraight Thread3/8-245/16-247/16-201/2-209/16-18 3/4-167/8-141 1/16-121 3/16-121 5/16-121 5/8-121 7/8-12 2 1/2-12 NominalPipe Size1/81/81/81/81/4 3/8 1/23/43/411 1/41 1/2 2 SAE Straight ThreadsUnion & Bulkhead (psi)5000500050005000 5000 4500350035003000300025002000 1500 Fittings withPipe Threads (psi)5000500050005000 5000 4000300030002500200011501000 1000 DEBURRING PRIOR TO FLARING:- To ensure satisfactory flares are produced, it may be necessary to deburr the tube end prior to flaring.

7 It is usually necessaryto break the inside corner smoothly before single flaring, and some non-ferrous tubing to eliminate is normally required to eliminate the cut off burr whichmight otherwise create leakage paths across a substantial portion of the flare. It is acceptable to smoothly break the outside corner prior to single flaring,or both outside and inside corners prior to double flaring, on any tube material to minimize Pressure given are for low carbon steel material only, Specifications are subject to change with out prior InformationMaterials & Thread Relevant StandardsPANAMF itting TypeMCMale ConnectorFCFemale ConnectorUUnionULLarge Hex UnionRAReducing AdapterSSleevesBUBulkhead UnionBHLNB ulkhead Lock NutNNutTCTube CapTCATube Cap AssemblyTPTube PlugMEMale ElbowPLMC45 Male ElbowUEUnion ElbowMBTMale Branch TeeMRTMale Run TeeFBTF emale Branch TeeFRTF emale Run TeeUTUnion TeeSRTS wivel Run TeeUCUnion CrossFEFemale ElbowP1 TypeNNPT ThreadsRISO Tapered ThreadsGISO Parallel ThreadsMMetric ThreadsSSAE/MS Straight ThreadsJ37 FlareSWLS wivel TypeAAdjustable TypeP1 Size11/1621/833/1641/455/16-2463/8 or 3/8-2477/16-208 or M8 x 199/16-18105/8 or M10 x 1123/4 or 3/4-16 or M12 x or M14 x or M16 x 1/16-1218M15 x 3/16-12201 1/4 or M20 x 5/16-1222M22 x or M24 x 5/8-1227M27 x 2301 7/8 or M30 x 2322402 - 12P2, P3.

8 And P4 Specify as perP Type and P SizeP - MC - 4N - 4N - SSMaterialSS316 SSBB rassCSCarbon SteelFeatures Size Ranges from 1/16 to 2 To avoid Galling threads are hardened with smooth surface which helps to extend the fittingservice life. For smooth flow path elbows are designed with radius junction. All Fittings are marked with Size, Material and Heat code for easy source tracing. All threads are capped for protection and properly packaged Straight Fittings are manufactured from bar stock & Forged Fittings aremanufactured from forgings All pipe threads meet the requirement if ASME/ANSI for taperedpipe threads (NPT) Working pressure meets the requirements of ANSI/ASME at ambient Relevant StandardsNPT ThreadsASME , SAE AS71051 ISO Tapered ThreadsISO 7-1, BS 21, JIS B0203 ISO Parallel ThreadsISO 228, JIS B0202 SAE/MSASME , SAE J475 MetricISO 261 MaterialBar StockForging316 SSASTM A276, ASME SA479,EN ASTM A276, ASME SA479,EN ASTM A182, ASME SA182,EN ASTM A182, ASME SA182,EN 304 SSASME B16/ASTM B453 ASTM B283 BrassASTM A108 ASTM A105 Carbon SteelMaterials like Hastloy,Monel, Duplex 2205,Duplex 2507 etc areavailable upon request3437 Flared Tube FittingsPart NoTube OD (P-PT) (P1-PT)

9 NPT 1/81/81/8 1/4 1/2 PMC-5J-2N-SS1 1 3 1 1 1 1 1 1/41/45/16 5/16 3/8 3/83/83/8 1/2 1/2 1/2 1/25/85/85/83/43/47/8111 1/41 1/41 1/21 1/22mm436 668 8 10 101010 12 12 12 Connectors - SAE 070102L EF - FlatP1-PTP-PT537 Flared Tube FittingsPart NoTube OD (P-PT) (P1-PT)SAE / MS3/8-245/16-247/16-20 1/2-20 9/16-18 PMC-4J-12S-SS3 9 7 1 1 1 1 1 5 3 5 1 3 5 1/41/41/4 5/16 3/8 3/83/8 1/2 1/2 1/2 1/2 5/85/85/83/43/43/43/47/87/8111mm436 666 8 10 101012 12 12 12 Connectors - SAE 070120P1-PTLF - Flat EP-PTPart NoTube OD (P-PT) (P1-PT)NPT1/81/81/8 1/8 1/4 PMC-8 SWL-6N-SS 3 1 1 1 1 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm436 81012 16 18 222532 38 Connectors - SwivelP1-PTF - FlatP-PTL E637 Flared Tube FittingsPart NoTube OD (P-PT) (P1-PT)NPT 1/81/81/8 1/4 1/8 PFC-5J-4N-SS1 1 1 1 3 3 1 1 1 1/45/165/16 3/8 3/8 1/2 1/25/8 3/4 3/4 7/8 11 1/422mm436 688 10 10 121216 18 18 22 Connectors - SAE 070103F - FlatP-PTL EP1-PTPart NoTube OD (P-PT) (P1-PT)NPT1/81/81/8 1/8 1/4 PFC-8 SWL-6N-SS 3 1 1 1 1 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm436 81012 16 18 222532 38 Connectors - SwivelF - FlatP1-PTLP-PT E737 Flared Tube FittingsPart NoTube OD (P-PT) 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm436 81012 16 18 222532 38 - SAE 070101P-PTF - FlatP-PTL EPart NoTube OD (P-PT) 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm436 81012 16 18 222532 38 Hex Unions - SAE 070119P-PTF - FlatP-PTL E37 Flared Tube Fittings8 Part OD (P-PT)inch 1/23/8 1/2 5/85/83/4 3/4 3/4 7/8 7/81 1 1 1 11 1/41 1/4mm121012 161618 18 18 222225 25 25 25 253232 Tube OD (P-PT)

10 Inch1/41/43/8 1/43/81/4 3/8 1/2 3/8 5/81/4 3/8 1/2 5/8 3/43/41mm6610 6106 10 12 10166 10 12 16 1/238 1 1/2383 1 1 Adapters - SAE OD (P-PT)inchmmPart No(inch)PS-3J-SSPS-2J-SSPS-4J-SSPS-6J-SS PS-8J-SSPS-10J-SSPS-12J-SSPS-14J-SSPS-16 J-SSPS-20J-SSPS-24J-SSPS-32J-SSPS-5J-SSP art No(mm) - 070115 3/161/81/4 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2436 81012 16 18 222532 38 50LP-PT937 Flared Tube FittingsPart NoTube OD (P-PT) 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm46 81012 16 18 222532 38 Lock Nuts - SAE 070118 LGPart NoTube OD (P-PT) 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm46 81012 16 18 222532 38 Unions - SAE 070601P-PTF - FlatP-PT ELTube OD (P-PT) (P-PT)SAE/MS3/8-245/16-247/16-20 1/2-20 9/16-183 1 3 1 5 1 5 7 2 1 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm436 81012 16 18 222532 38 50 Part NoinchPN-3J-SSPN-2J-SSPN-4J-SSPN-6J-SSPN -8J-SSPN-10J-SSPN-12J-SSPN-14J-SSPN-16J- SSPN-20J-SSPN-24J-SSPN-32J-SSPN-5J-SSPar t - SAE 070110LP-PTF - Flat37 Flared Tube Fittings10 Part NoTube OD (P-PT) 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm436 81012 16 18 222532 38 Caps - SAE 070109LP-PTF - Flat EPart NoTube OD (P-PT) 1/45/16 3/8 1/2 5/8 3/47/8 1 1 1/4mm34 6810 12 16 182225 1 1/2 Cap Assembly - SAE 070112 ALP-PTF - Flat1137 Flared Tube FittingsPart NoTube OD (P-PT) 5/163/8 1/2 5/8 3/4 7/81 1 1/4 1 1/2 2mm436 81012 16 18 222532 38 Plugs - SAE 070112F - FlatP-PTL EPart NoTube OD (P-PT) (P1-PT)