Transcription of 5619, Guardian Dual Check 1/4 Turn Non-Freeze Hydrant with ...
1 5-17-11 Added Note TBW CLF 6-13-11 Revised Note TBW CLDATEDESCRIPTIONBYCKD. BYWEIGHTPOUNDSVOLUMECUBIC FEETFIGURE NUMBERLOCATIONFIGURENUMBERDIMENSIONS ARE SUBJECT TO MANUFACTURERS TOLERANCE AND CHANGE WITHOUT NOTICEWE CAN ASSUME NO RESPONSIBILITY FOR USE OF SUPERSEDED OR VOID DATADRAWN BY:CHECKED BY:APPROVED BY:DATE:SCALE:SIZEADRAWING NUMBER56195619 RNCLHCEL3-24-03 NONEs5619 OPTIONAL MATERIALS:Polished Bronze Face -PBChrome Plated Face -CP5(125)1 1/2" (38) 1/8(3)TOP VIEWFRONT VIEW1/2 (13) FemaleNPT Inlet3/4 (19) MaleNPT InletAdjustableWall Clamp(Specify -WC)(Note 4)FIG. 56192 9/16 (64)EXPOSED HOSE CONNECTIONFUNCTION: For installation in interior or exterior building walls where an exposed hose connection is positive Non-Freeze protection.
2 Adaptable to all types of wall FURNISHED: Guardian DUAL CHECK1/4 turn Non-Freeze WALL Hydrant WITH AUTOMATIC DRAININGINTEGRAL VACUUM BREAKER AND DUAL Check VALVE 1/4 turn of the Key Allows Full Flow to Be Obtained3/4 HoseConnectionIntegral Vacuum Breakerand Dual Check Valve"T" Handle KeyBronze Quarter turn Non-FreezeAutomatic Draining Hydrant with Stainless Steel Face, Hose Connection, Integral Vacuum Breaker and Dual Check Valve and "T" Handle ANSI SpecificationsComplies w/ ASSE 1019-B,1052 and Listed- File #2749 Patent No. US 6,752,167 5. Add 3/4 (19) to Overall Length When SpecifiedNOTES:1.
3 Recommended wall opening 2 1/4 (57) x 4 (100). 2. When ordering, specify wall thickness in 1 (25) increments as follows 4,5,6,7, When wall clamp -WC is desired, increase wall thickness dimension by 2 (51). 3. All Jay R. Smith hydrants are manufactured with "NO-LEAD" brazing rings, and USDA approved lubricants. 6. When specifying Fig. 5619 (-SAP) the wall thickness shall be 2 (51).7. Dimensions shown in parentheses are in The AB1953, California Lead Law, and NSF/ANSI Standard 61-2008 - Drinking Water System Components are not applicable to Jay R.
4 Smith hydrants as they do not convey/dispense water for human consumption through drinking or FOR IRRIGATION PURPOSES :Adjustable Wall Clamp -WC (Note 4)1 (25) Hose Connection -HC11 (25) Male NPT Inlet Connection -IC1 (Note 5)Mild Climate -SAP (Note 6)Wheel Handle (-WH)Wall Thickness(Note 2)G 2-4-13 Revised Notes TBW CLH 4-5-18 Added Notes TBW BWWARNING: Cancer and Reproductive Harm - CO. MEMBER OF MORRIS GROUP INTERNATIONALPOST OFFICE BOX 3237 MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 MEMBER OF:ASPE SANITARYENGINEERINGP revention Rather Than CureSINCE 1926 PLUMBING AND DRAINAGE INSTITUTE MEMBER MEMBERI nstaller is responsible for providing a 100% watertight positive seal at the Hydrant to wall interface.
5 Seal all the flange with an appropriate sealant recommended by a sealant manufacturer. NOTE: Jay R. Smith does not warrant the perfor-mance or life expectancy of the sealant of a small amount of water may occur from the Vacuum Breaker upon the initial opening and closing of this Hydrant . This is normal BYWEIGHTPOUNDSVOLUMECUBIC FEETFIGURE NUMBERLOCATIONFIGURENUMBERDIMENSIONS ARE SUBJECT TO MANUFACTURERS TOLERANCE AND CHANGE WITHOUT NOTICEWE CAN ASSUME NO RESPONSIBILITY FOR USE OF SUPERSEDED OR VOID DATADRAWN BY:CHECKED BY:APPROVED BY:DATE:SCALE:SIZEADRAWING NUMBER5619BS5619 BSRNCLACEL3-24-03 NONES5619 BSGUARDIAN DUAL Check Hydrant PARTS LISTHYDRANT PARTS Casing Assembly2 Wall Plate Assembly3 Key4 Wall Plate Securing Screw (5) 5 Wall Plate Gasket1a Head1b Casing1c Valve Housing6 Stationary Operator Piece10 Operator Rod11 Operator Rod Guides (2)12 Vacuum Breaker/Dual Check Valve Assembly 7 Moveable Operator Piece8 Moveable Operator O-Ring 9 Drain Hole Seal (2)12a **Vacuum Breaker Housing12e **Flow Diverter12f **Large O-Ring12b **Spring (2)12c **Cone Washer (2)
6 12d **Small O-Ring13e **Valve Actuator13f **Nylon Thrust Washer13g **Rotating Ceramic Disc 13d **Nylon Thrust Spacer13j **O-Ring 13k **O-Ring Gasket Retainer13m **Rubber Seal 13h **Fixed Ceramic Disc13 actuator Cartridge Assembly13a **Retaining Ring13b **Valve Body13c ** actuator O-Ring (2)**4259781110116**131313a13b13c13d13e1 3f13g13h13j13k13mActuator Cartridge AssemblyThese Parts Accessible from Face of Hydrant by Removing Wall Plate Assembly. These Replacement Parts Available in HPRK-19*Parts supplied as an assembly only, see part 12 or 13.**These Replacement Parts Available in HPRK-19VB**42*12a*12b*12c12 Vacuum Breaker/Dual Check Valve Assembly*12d*12e*12f*12b*12c*51331a511c1 b12101172968 JAY CO.
7 MEMBER OF MORRIS GROUP INTERNATIONALPOST OFFICE BOX 3237 MONTGOMERY, ALABAMA 36109-0237 (USA)TEL: 334-277-8520 FAX: 334-272-7396 MEMBER OF:ASPE SANITARYENGINEERINGP revention Rather Than CureSINCE 1926 PLUMBING AND DRAINAGE INSTITUTE MEMBER MEMBERWARNING: Cancer and Reproductive Harm - 4-5-18 Added Note TBW BW Installer is responsible for providing a 100% watertight positive seal at the Hydrant to wall interface. Seal all the flange with an appropriate sealant recommended by a sealant manufacturer. NOTE: Jay R. Smith does not warrant the performance or life expectancy of the sealant material.