600WOG/150WSP Full Port Two-piece Brass Ball …

1 E-211=02. 600 WOG/150 WSP full Port Two-piece Brass Ball valves 600 WOG/150 WSP full Port Fig. Two-piece Brass Ball valves SZA ( for BS21 threaded ends ). AKSZA ( ). [Code#58] for NPT threaded ends - ASME B CSZA ( ). [Code#59] for solder joint ends - ASME B All sizes rated 600 WOG / 150 WSP (400 WOG for 4 ) Quick quarter-turn for easy operation Conforms to specification of MSS-SP-110 AKSZA / CSZA Three types of end connection design Maintenance Free, Double O -ring stem seal and BS21 threaded end connection PTFE seats NPT threaded end connection Two-piece construction with a chrome plated Brass ball Solder joint end connection Blowout - proof stem Approvals Construction and Materials AKSZA ( 1 4 through 2 ). CSA : 1 2 psig at the appliance CSA : 5 psig from the appliance to the meter CSA : 125 psig from the meter to the street AKSZA / CSZA ( 1 4 through 2 ). 10. UL / FM : for fire protection 9. Note : CSA-Canadian Standards Association Consolidation of the American Gas Association (AGA) and the Canadian Gas Association (CGA).

2 UL - Underwriters Laboratories 47. FM - Factory Mutual Application 45. Water, Oil, Gas, and Steam 3. Maximum Working Pressure Working Pressure Non-Shock Test Pressure Unit Cold Water, Oil, Gas Shell Hydrostatic 1. Saturated Steam 1 4 1 4 Seat Air . 3 4 3 4 . psi 150 600 400 900 600 80. MPa 30. Bar kgf/cm2 10 42 28 63 42 6 4. Note : For more details, please refer to P-T rating chart. 30. Effecttive Length of Thread unit : mm inch . Size 1 3 1 3 1 11 4 11 2 . 4 8 2 4 2. Super Z 9 12 13 . ZA/AKZA 8 10 11 12 13 14 . Size 2 21 2 3 4 . Super Z . ZA/AKZA Illustration shows threaded ends design up to 2 . No. Parts Q'TY Materials (ASTM). P-T Rating . 1 Body 1 Forged Brass (B283 No. C37700)/Cast Bronze (B584 No. C84400) 1. psi MPa .. 2 Body Cap 1 Forged Brass (B283 No. C37700)/Cast Bronze (B584 No. C84400) 1. 600 4 Advisory Note : . 3 Stem 1 Brass Rod (B16) 2. Please be advised that applications . 4 Ball 1 Forged Brass (B283 No. C37700) 3/Cast Brass 3 4.

3 500. in the shaded zone will reduce 3 the service life of the valve.. 9 Handle 1 Carbon Steel 4/Ductile Iron 5. 400. 4 only The maximum working pressure . 10 Handle Nut 1 Carbon Steel Pressure 300 2. and temperature of solder jointed . 30 Ball Seat 2 PTFE. valves are limited by the properties 200 of solder and tube materials.. 45 O-ring 2 FPM 6. 150 1 Information on typical solder materi- . 47 Thrust Washer 1 PBT 7/ PTFE 8. 100 als are provided on the back cover Note: of this catalog. 5 3 and 4 . 0 1 21/2 through 4 . 0 50 100 150 C . 185 200 2 Ni plating 6 Fluorocarbon Elastomer 38 3 Cr plating 7 Polybutylene Terephthalate 0 100 200 300 F . 366 392 4 Plastic covering 8 21/2 and up Temperature Dimensions and Cv Value Threaded Ends Design Solder Joint Ends Design SZA : BS21 thread : Solder joint Fig. : NPT thread Fig. CSZA. AKSZA [Code#59]. [Code#58]. D1 D1. Tagging hole Tagging hole Tagging hole Tagging hole size 1 4 & 3 8 size 1 2 through 21 2 size 3 8 size 1 2 through 21 2.

4 H H. d d S1. L L. Nominal d H D1 L S1 Cv Nominal d H D1 L Cv size Value size Value mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch mm inch 14 10 37 70 42 20 . 38 10 37 70 42 22 38 10 37 70 42 12 15 40 80 53 26 12 15 40 80 53 34 20 43 80 60 32 34 20 43 80 60 1 25 49 110 72 39 1 25 50 110 72 11 4 32 55 110 84 48 11 4 32 55 110 84 11 2 40 64 150 92 55 11 2 40 64 150 92 2 50 72 150 110 68 2 50 72 150 110 21 2 65 101 200 138 84 21 2 65 101 200 164 3 76 112 300 167 99 3 76 112 300 187 4 100 131 300 193 125 600 WOG/150 WSP full Port Two-piece Brass Ball valves Information for a Sound Solder Joint CAUTION. , Don t use valves for super-heated steam service. Refer to the maximum working pressure shown in the pressure-temperature rating. , Don t use valves with intermediate opening positions. Pressurizing partly open valves will cause seat deformation, and internal fluid leakage. , CAUTION Don t apply any external force counterclockwise to the valve cap.

5 It may affect the assembly of valve body to cap, and cause external fluid leakage. , Don t apply an excessive force when threading pipes into valve bores. It will cause seat deformation, and operational difficulty. Adequate threading torques are given below: 2. Copper Tubes Valve Size 14 1 2 3 4 1 11 4 11 2 2 2 1 2 3 4 . Prepare copper tubes conforming to ASTM B 88 Threading Torque 20 39 49 59 69 78 108 127 . "Seamless Copper Water Tubes" ( N m ) 29 49 59 69 78 88 118 137. 3. P-T Rating of Solder Jointed valves The maximum service pressure and temperature of solder jointed valves are limited by the properties of solder and tube materials. Information on typical solder materials are provided below : CAUTION. Maximum working pressure Pressure-temperature ratings and other performance data published Solders Size 1 4 1 Size 11 4 . 2 Size 21 2 . 3 . in this catalog have been developed from our design calculation, MPa psi MPa psi MPa psi in-house testing, field reports provided by our customers and/or pub- 95-5 tin-antimony 100 38 500 400 300 lished official standards or specifications.

6 They are good only to cover H95 Sb-5A 150 66 400 350 275 typical applications as a general guideline to users of KITZ products 96-4 tin-silver 200 93 300 250 200 introduced in this catalog. H96 121 250 200 175 150 For any specific application, users are kindly requested to contact KITZ Corporation for technical advice, or to carry out their own study CAUTION and evaluation for proving suitability of these products to such an appli- cation. Failure to follow this request could result in property damage To determine the maximum working pressure of solder jointed and/or personal injury, for which we shall not be liable. valves , apply those of valve themselves or employed solder materials, whichever is lower. While this catalog has been compiled with the utmost care, we Copper tubes should not be used for steam service. assume no responsibility for errors, impropriety or inadequacy. Any Don't exceed a service velocity greater than 6ft/sec , information provided in this catalog is subject to from-time-to-time to prevent erosion of copper tube.

7 Erosion results in a change without notice for error rectification, product discontinuation, considerable damage partially to the surface of metal, due to the design modification, new product introduction or any other cause that fluid corrosion accelerated by mechanical stress of high fluid KITZ Corporation considers necessary. This edition cancels all previ- velocity. ous issues. Distributed by ISO 9001 certified since 1989. 1-10-1,Nakase, Mihama-ku, Chiba 261-8577, Japan International Sales Dept. Phone:81-43-299-1730, 1732 and 1733. Fax:81-43-299-0121. Printed in Japan 0603 ITP.