1 7060. 7208 0682. INSTALLATION MANUAL. No forest has been destroyed to produce this 100% recycled paper. by GEMINI TRADING Via Luigi Galvani 12 21020 Bodio Lomnago (VA) Italia Tel. +39 0332 943211 - Fax +39 0332 948080. AC 2529 - REV. 00 / 06 / 01. E-mail : "DIP SWITCHES PROGRAMMING TABLE". DESCRIPTION 1 OFF Comfort POSITIVE. GEMINI 7060 2 ON Comfort NEGATIVE. The system 7060 is an alarm unit that can be installed on vehicles with 12 volts battery (negative earth). 2 OFF Automatic arming OFF. 2 ON Automatic arming ON. FUNCTIONS 3 OFF Self-learning of a new code OFF (normal use). - remote controlled alarm unit with dynamic code.
2 3 ON Self-learning of a new code ON. - Blinker, universal central door locking control, electric windows and sunroof closure for selected vehicles 4 OFF Closure short * period equipped with Pack Comfort system. 4 ON Closure 6 seconds - Perimetric protection and outlet for additional modules. * THESHORT TIME IS SET FROM THE PROGRAMMING WITH THE TWO-CHANNELS TRANSMITTER. - Controls for self-powered siren, additional siren (continuous or alternate sound) and horn. BETWEEN 0,5 SECONDS AND 1 SECOND. - LED's Memory. ATTENTION : SET THE DIP SWITCHES BEVOR FEEDING THE 7060 UNIT. - Acoustic activation/de-activation (through siren or horn).
3 - remote controlled panic function and / or boot opening. - Electric engine immobilisation. TABLE OF PROGRAMMABLE FUNCTIONS THROUGH THE TWO-CHANNELS TRANSMITTER. - Alarm unit functions programmable through the transmitter. VISIBLE LED FLASHING AND ALTERNATIVE. ACTIONS ALARM CONDITION. The unit is equipped with two 2-channel transmitters (art. 7208E), frequency Mhz. ACTIONS SELECTED FUNCTIONS ACTIONS. POWER OFF Alarm OFF - - - USEFUL SUGGESTIONS FOR THE INSTALLATION Turn the ignition Alarm OFF - - - key to ON. - Connect the positive and negative feeding wire of the alarm system to the battery. FEED THE UNIT.
4 - Connect always the alarm Green-Brown wire to the door pin switch. Alarm ON - - - 7060. - On catalysed vehicles the engine immobilisation must be carried out on the fuel pump and the starter motor. Press on the One flashing = continuous Access to the Set-up 1 function: One blinker transmitter 1 button - Avoid routing connection wires next to interference sources. within 10 seconds Supplementary siren flashing Two flashing = intermittent - The ultrasonic heads must be positioned at the top of each windscreen pillar and must be pointing at each Access to the Set-up 2 function: One flashing = de-activated opposite diagonal corner away from the facia outlets.
5 Press on the acoustic signalling with Two blinker transmitter 1 button flashing supplementary siren 725 Two flashing = activated WIRING CONNECTIONS. Disconnect the negative terminal of the battery and only re-connect after the installation is complete. One flashing = Panic and Access to the Set-up 3 function: Three Press on the additional siren Press on the FUNCTION WIRE COLOR transmitter 1 button Panic and boot opening through blinker transmitter Earth BROWN the transmitter flashing Two flashing = Boot opening button N. 2 to Battery positive terminal RED One flashing = change the Access to the Set-up 4 function: selected option.
6 Engine immobilisation (max. 10 A) 2 X GREY Press on the boot opening while alarm armed Four blinker While alarm disarmed Ignition live YELLOW transmitter 1 button flashing Two flashing =. (Panic excluded) De-activate the For both functions Direction indicator lights 2 x ORANGE +15 to memorise Access to the Set-up 5 function: One flashing = de-activated Door pin switch GREEN-BROWN Press on the vehicle check while arming the Five blinker the selected Boot/bonnet pin switches GREEN flashing options and to transmitter 1 button system Two flashing = activated Positive alarm armed PINK One flashing = 0,5 seconds exit from User Press on the Access to the Set-up 6 function: Six blinker set-up.
7 External sensors inlet GREEN-BLACK closure control period flashing transmitter 1 button Self-powered siren control BLUE Two flashing = 1 seconds Common +/- siren or klaxon BLACK Access to the Set-up 7 function: Seven One flashing = activated Press on the Automatic arming with door blinker Additional siren or horn control YELLOW-BLACK transmitter 1 button closure flashing Two flashing = de-activated Negative control boot opening GREY-BLACK One flashing = while closing Comfort WHITE-BLACK Eight Press on the Access to the Set-up 8 function: blinker Central door locking YELLOW-BLUE, RED-BLUE, YELLOW-GREY, transmitter 1 button Comfort flashing Two flashing = after the RED-GREY, YELLOW-BROWN, RED-BROWN closure Note: The wiring harness has 2 connectors: connect the 2-pin connector to the LED and the 4-pin Turn the ignition Set-up exit, normal working - - - connector to an additional module (shock, ultrasonic or super-high frequency module).
8 Key to OFF of the alarm Recapitulatory table of the programmable functions through the two -channels transmitter. PANIC FUNCTION. Function Manufacturer function Programmable function To obtain this function with the alarm armed after the neutral time, press on the transmitter button N. 2 (if the 4. 1 Additional siren outlet Continuous sound Alternate sound function- boot opening with alarm armed is de-activated). The siren, the klaxon and the direction indicator lights 2 Acoustic signalling De-activated Activated activate. To de-activate this function within the 10 seconds of the alarm cycle, press on the transmitter button 3 Boot opening with alarm disarmed De-activated Activated N.
9 2. 4 Boot opening with alarm armed With alarm disarmed if the 3 Both functions LEDS MEMORY. functions has been activated (Panic excluded). While disarming the alarm, turn the ignition key to ON to check if an attempted break-in has occurred. 5 Vehicle's check De-activated Activated Following the Led flashing it is possible to know the alarm triggering's cause. The signalisation is repeated for 6 Central door locking short period 0,5 seconds 1 second 5 times. 7 Automatic arming Activated De-activated 8 Comfort While closing the doors After the blinker flashing Signalling LED Alarm triggering Alarm cycle l Door and boot/bonnet pin switches.
10 10. WORKING DESCRIPTION l Ignition live Unlimited - ALARM ARMING: press on the transmitter's button N. 1. One pulse of the direction indicator lights signals l External sensors 10. the arming. l LED OFF (2 seconds) LED ON (1 second). - EXCLUSION OF THE VOLUMETRIC SENSOR, EXTERNAL SENSORS AND COMFORT CONTROL Each alarm cycle is 30 seconds AFTER THE ALARM ARMING: while alarm armed (even if the boot opening function with alarm armed is The inhibit time is 30 seconds for all alarm triggering's cause. activated), during the inhibit time (Led lightning fix) press on the transmitter 2 button. The exclusion is signalled by one pulse of the direction indicator lights, the comfort function and the sensors are excluded.