Example: marketing

802.11ac Dual-Radio Long Range Access Point - Ubiquiti

Dual-Radio long Range Access PointModel: UAP-AC-LRIntroductionThank you for purchasing the Ubiquiti Networks UniFi AP. This Quick Start Guide is designed to guide you through installation and also includes warranty : The UAP-AC-LR requires the UniFi Controller or higher, available at: ContentsUniFi AP AC LRMounting BracketCeiling Backing PlateFlat Head Screws (Qty. 4)Keps Nuts (Qty. 4)Screws (Qty. 4)Screw Anchors (Qty. 4) Dual-Radio long Range Access PointModel: UAP-AC-LRGigabit PoE* (24V, ) with Mounting BracketPower Cord*Quick Start Guide* Included only in the single-pack of the Requirements CAT5/6 cable Phillips screwdriver drill and drill bit (6 mm for wall-mounting or 3 mm for ceiling-mounting) Optional: Drywall or keyhole saw (to cut 18 mm hole for Ethernet cable feed)TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above).

drill bit to drill the mounting holes. Arrow 3. If your Ethernet cable feeds through the wall, then cut or drill a circle approximately 18 mm in diameter. Then feed the CAT5/6 cable through the hole. 25 mm Note: 25 mm is the distance from the center of the bottom mounting hole to the center of the cable hole.

Tags:

  Ranges, Radio, Access, Points, Long, Drill, Dual, 11ac, Drill bits, 11ac dual radio long range access point

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of 802.11ac Dual-Radio Long Range Access Point - Ubiquiti

1 Dual-Radio long Range Access PointModel: UAP-AC-LRIntroductionThank you for purchasing the Ubiquiti Networks UniFi AP. This Quick Start Guide is designed to guide you through installation and also includes warranty : The UAP-AC-LR requires the UniFi Controller or higher, available at: ContentsUniFi AP AC LRMounting BracketCeiling Backing PlateFlat Head Screws (Qty. 4)Keps Nuts (Qty. 4)Screws (Qty. 4)Screw Anchors (Qty. 4) Dual-Radio long Range Access PointModel: UAP-AC-LRGigabit PoE* (24V, ) with Mounting BracketPower Cord*Quick Start Guide* Included only in the single-pack of the Requirements CAT5/6 cable Phillips screwdriver drill and drill bit (6 mm for wall-mounting or 3 mm for ceiling-mounting) Optional: Drywall or keyhole saw (to cut 18 mm hole for Ethernet cable feed)TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above).

2 It is the professional installer s responsibility to follow local country regulations, including operation within legal frequency channels, output power, indoor cabling requirements, and Dynamic Frequency Selection (DFS) Requirements Linux, Mac OS X, or Microsoft Windows 7/8/10 Java Runtime Environment ( or newer recommended) Web Browser: Google Chrome (Other browsers may have limited functionality.) UniFi Controller software or higher (available at: )Network Topology Requirements A DHCP-enabled network (for the AP to obtain an IP address as well as for the wireless clients after deployment) A UniFi Cloud Key or management station running the UniFi Controller (or newer) software, located either on-site and connected to the same Layer-2 network, or off-site in the cloud or a NOCUS-16-150 WUSG-PRO-4(DHCP Server)InternetUAP-AC-PROUAP-AC-LRLANWAN UniFi Cloud Key(UniFi Controller)

3 UAP-AC OutdoorRemote Access toUniFi ControllerDOWNLOAD THROUGHPUT & LATENCYDEVICES ON GHZ CHANNELDEVICES ON 5 GHZ CHANNELUPLOAD THROUGHPUT & LATENCYLATENCYTHROUGHPUTSPEED +0700+ DEVICEWANI nactive 0 Pending 0 Inactive 0 Pending 07 ACTIVE DEVICESI nactive 0 Pending 0118 ACTIVE DEVICESLANWLANDEEP PACKET INSPECTIONCLIENTSDEVICES2502001501005001 08642024 HRS12 HRSNOWAvg/Max ThroughputLatencyLatency [msec]Throughput [Mbps]100806040200108642024 HRS12 HRSNOWL atency [msec]Throughput [Mbps]Network ProtocolsStreaming MediaWeb / Web TransferSocial NetworkOtherMotorolaLenovoSamsungEDellAc erOtherWLANLANWAN11871582 GB258241220213130110126 DEVICES645 GBTRAFFIC1172 CLIENTS1 2 3 4 5 6 7 8 9 10 1136 40 44 48 52 56 60 64100 104 108 112 116 120 124 128132 136 140 144 149 153 157 161 165 CURRENT SITED efaultUSERNAME adminSample Network DiagramAll UniFi devices support off-site management controllers.

4 For setup details, see the User Guide on the website: OverviewLEDLED ColorStatusWhiteFactory default, waiting to be WhiteInitializing. Alternating White/BlueDevice is busy; do not touch or unplug it. This usually indicates that a process such as a firmware upgrade is taking the device has been successfully integrated into a network and is working properly. Quickly Flashing BlueThis is used to locate an AP. When you click Locate in the UniFi Controller software, the LED on the AP will flash. It will also display the location of the AP on the Blue with occasional flashingIndicates the device is in an isolated state (all WLANs are brought down until an uplink is found).PortsLocking NotchCable Feed PlugReset ButtonEthernet PortLocking Notch The Locking Notch will be used with the Mounting Bracket to help secure the UniFi AP.

5 (This is described further in the Mounting Bracket section.)Ethernet This Gigabit Ethernet port is used to connect the power and should be connected to the LAN and DHCP server. Power can be provided by a Ubiquiti Networks UniFi Switch with PoE or Gigabit PoE adapter (included with single-pack only).Reset The Reset button serves two functions for the UniFi AP: Restart Press and release the Reset button quickly. Restore to Factory Default Settings Press and hold the Reset button for more than five , the UniFi AP may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Feed Plug If your Ethernet cable feeds along the mounting surface, remove the Cable Feed BracketLocking TabMounting BracketLocking Tab During installation, the Locking Tab on the Mounting Bracket moves from the Initial Position to the Final Position, where the Locking Tab fits securely into the Locking Notch on the UniFi AP to help prevent theft.

6 Initial PositionSlotFinal PositionNote: If you need to remove the UniFi AP from the Mounting Bracket, insert a paper clip in the Slot to release the Locking Tab and turn the UniFi AP InstallationThe UniFi AP can be mounted on the wall or ceiling. Perform the steps for the appropriate installation:Wall Mount1. Position the Mounting Bracket at the desired location on the wall with the arrow pointing Use a pencil to mark the four mounting holes. Use a 6 mm drill bit to drill the mounting If your Ethernet cable feeds through the wall, then cut or drill a circle approximately 18 mm in diameter. Then feed the CAT5/6 cable through the mmNote: 25 mm is the distance from the center of the bottom mounting hole to the center of the cable Insert the Screw Anchors into the 6 mm holes. Secure the Mounting Bracket to the wall by inserting the Screws into the If the Ethernet cable runs along the mounting surface, then remove the Cable Feed Connect the Ethernet cable to the Ethernet port.

7 7. Align the arrow on the UniFi AP with the arrow on the Locking Tab of the Mounting TabArrow8. Ensure that the UniFi AP is firmly seated on the Mounting Bracket. Turn the UniFi AP clockwise until it locks into place and the Locking Tab fits securely into the Locking Mount1. Remove the ceiling Place the Ceiling Backing Plate in the center of the ceiling tile. Mark the four mounting screw Mark a hole approximately 18 mm in diameter for the Ethernet cable mmNote: 25 mm is the distance from the center of the bottom mounting hole to the center of the cable Use a 3 mm drill bit to drill the screw holes, and cut or drill the hole for the Ethernet cable Insert the Flat Head Screws through the Mounting Bracket, ceiling tile, and Ceiling Backing Plate. Fasten the screws using the Keps Nuts. Then feed the Ethernet cable through the 18 mm Connect the Ethernet cable to the Ethernet Align the arrow on the UniFi AP with the arrow on the Locking Tab of the Mounting TabArrow8.

8 Ensure that the UniFi AP is firmly seated on the Mounting Bracket. Turn the UniFi AP clockwise until it locks into place and the Locking Tab fits securely into the Locking Set the ceiling tile back into the UniFi APUse a UniFi Switch with PoE or a Gigabit PoE adapter for to a UniFi Switch with PoEConnect the Ethernet cable from the UniFi AP directly to a PoE port on the UniFi Switch with 3 5 7 9 11 13 15 17 19 21 222 4 6 8 10 12 14 16 18 20 22 24 SPF1 SPF2 UniFi Switch with PoE Power Connection

9 Diagram*640-00184-11*640-00184-11 Connecting Power over EthernetThe single-pack of the UAP-AC-LR includes one Gigabit PoE adapter. For multi-pack units, we recommend using a UniFi Connect the Ethernet cable from the UniFi AP to the adapter s POE Connect an Ethernet cable from your LAN to the adapter s LAN port. 3. Connect the Power Cord to the adapter s power port. Connect the other end of the Power Cord to a power the PoE Adapter (Optional)1. Remove the PoE Mounting Bracket from the adapter, place the bracket at the desired location, and mark the two holes. 2. Pre- drill the holes if necessary, and secure the bracket using two fasteners (not included).3. Align the adapter s slots with the tabs of the PoE Mounting Bracket, and then slide the adapter InstallationDownload and install the latest version of the UniFi Controller software.

10 Launch it and follow the on-screen instructions. The software and step-by-step instructions in the User Guide are available at: you have installed the software and run the UniFi Installation Wizard, a login screen will appear for the UniFi Controller management interface. Enter the Admin Name and Password that you created and click Log In. You can manage your wireless network and view network statistics using the UniFi Controller management interface. For information on configuring and using the UniFi Controller software, refer to the User App InstallationUbiquiti Networks also offers the UniFi mobile app, which is available from the App Store (iOS) or Google Play Store (Android). You can use it to provision a UniFi AP for basic functionality without configuring a UniFi Controller. It also allows seamless provisioning of APs for remote controllers (controllers not on the same Layer 2 network) and easy Access to local controllers and those monitored on x x mm ( x x ")Weight With Mounting Kits240 g ( oz)315 g ( oz)Networking Interface(1) 10/100/1000 Ethernet PortButtonsResetPower MethodPassive PoE (Pairs 4, 5+; 7, 8 Return)Power Supply24V, PoE Gigabit Adapter1 Max.


Related search queries