Example: quiz answers

9HUVD%RQG 3URIHVVLRQDO7KLQ 6HW0RUWDU 7'6 …

VersaBond Professional Thin Set Mortar / TDS 1191 Product NameVersaBond Professional Thin Set Mortar2 ManufacturerCustom Building ProductsTechnical Services10400 Pioneer Boulevard, Unit 3 Santa Fe Springs, CA 90670 Customer Support: 800-272-8786 Technical Services: 800-282-8786 Fax: 800- 200-7765 Email: DescriptionA professional formula, all-purpose mortar, polymer-modified toprovide good bond strength for floor and tile projects. VersaBond cures quickly even in cold climates and adheres to most surfaces,exceeding ANSI and without the need for FeaturesFor most standard installationsFast setting even in cold weatherSuitable Tile TypesVitreous, semi-vitreous or non-vitreous tile: ceramic, mosaic, quarry, cement body tileImpervious porcelain and glass tileBrick and thin brickCement-based precast terrazzoNatural stone tileSuitable SubstratesConcrete, mortar beds, masonry, portland cement plasterWonderBoard Lite cement backerboardLiquid applied waterproofing membranes suchas RedGard and Custom 9240 Crack prevention sheet membranes such as Crack Bus

Mar 27, 2018 · Cement-based precast terrazzo Natural stone tile Suitable Substrates Concrete, mortar beds, masonry, Portland cement plaster WonderBoard Lite cement backerboard Liquid applied waterproofing membranes such as RedGard and Custom 9240 Crack prevention sheet membranes such as Crack Buster Pro

Tags:

  Sheet, Cement, Portland, Portland cement

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of 9HUVD%RQG 3URIHVVLRQDO7KLQ 6HW0RUWDU 7'6 …

1 VersaBond Professional Thin Set Mortar / TDS 1191 Product NameVersaBond Professional Thin Set Mortar2 ManufacturerCustom Building ProductsTechnical Services10400 Pioneer Boulevard, Unit 3 Santa Fe Springs, CA 90670 Customer Support: 800-272-8786 Technical Services: 800-282-8786 Fax: 800- 200-7765 Email: DescriptionA professional formula, all-purpose mortar, polymer-modified toprovide good bond strength for floor and tile projects. VersaBond cures quickly even in cold climates and adheres to most surfaces,exceeding ANSI and without the need for FeaturesFor most standard installationsFast setting even in cold weatherSuitable Tile TypesVitreous, semi-vitreous or non-vitreous tile: ceramic, mosaic, quarry, cement body tileImpervious porcelain and glass tileBrick and thin brickCement-based precast terrazzoNatural stone tileSuitable SubstratesConcrete, mortar beds, masonry, portland cement plasterWonderBoard Lite cement backerboardLiquid applied waterproofing membranes suchas RedGard and Custom 9240 Crack prevention sheet membranes such as Crack Buster ProUncoupling membranes such as RedGard Uncoupling MatSurfaces treated with MBP Multi-Surface Bonding PrimerExterior Grade Plywood (interior residential and light commercial dryareas)Gypsum wallboard (interior dry areas)Existing ceramic tile (scarified)Fully-bonded sheet vinyl flooring (scarified)Plastic laminates (scarified)

2 Cutback adhesive (see preparation instructions)Composition of ProductVersaBond Fortified Thin Set Mortar is a dry, proprietary blend ofPortland cement , copolymers, inorganic aggregates and chemicalsBenefits of Product in the InstallationCost-efficient, all-purpose mortarGood bond strengthCures quickly even in cold climatesApproved for industry-recommended interior and exterior applicationsExceeds ANSI and standards without the need foradditivesLimitations to the ProductDo not bond directly to hardwood, Luan plywood, particle board,parquet, cushion or sponge-back vinyl flooring, metal, fiberglass,plastic or OSB recommended for interior and exterior pools and water recommends MegaLite Crack Prevention Mortar.

3 MegaFlex Crack Prevention Mortar and ProLite Large Tile andStone Mortar for the installation of ceramic and porcelain tile insubmerged applications. For additional information, contact CustomTechnical setting moisture sensitive natural stone, cement or agglomeratetile use EBM Lite Epoxy Bonding Mortar 100% Solids or CEG Lite 100% Solids Commercial Epoxy not use to install resin-backed stone; use EBM Lite Epoxy BondingMortar 100% Solids, CEG Lite 100% Solids Commercial Epoxy Groutor contact Custom's Technical Services for clear or translucent glass, CUSTOM recommends Glass TilePremium Thin-Set Mortar. When setting glass tile larger than 6" x 6"(15 x 15 cm), contact Custom's Technical Services setting dimensional stone larger than 12" x 12" (30 x 30 cm),contact Custom's Technical Services for recommendations regardingsubfloor deflection lb ( kg) and 25 lb ( kg) bagsGray or whiteVersaBond Professional Thin Set MortarPublished Date.

4 3/27/2018 VersaBond Professional Thin Set Mortar / TDS 1194 Technical DataApplicable StandardsAmerican National Standards Institute (ANSI) ANSI , of the American National Standards for the Installation ofCeramic Tile ASTM International (ASTM)ASTM C109 Standard Test Method for Compressive Strength ofHydraulic cement Mortars (Using 2-in or [50-mm] Cube Specimens)ASTM C627 Standard Test Method for Evaluating Ceramic Floor TileInstallation Systems Using the Robinson-Type Floor Tester Resilient Floor Covering Institute - (RFCI) Recommended WorkPractices for Removal of Resilient Floor Coverings Tile Council of North America (TCNA) - TCNA Handbook for CeramicTile Installation, TCNA Method EJ171 ISO 13007-2 Technical ChartPropertyTest MethodRequirementTypical ResultsPot Life 4 > 20 minutesPass4 Week Shear Bond StrengthGlazedWall > 300 psi450 - 550 psi( kg/cm ) > 200 psi300 - 400 psi( kg/cm )QuarryTile > 150 psi150 - 250 psi( kg/cm )Environmental ConsiderationCustom Building Products is committed to environmentalresponsibility in both products produced and in manufacturingpractices.

5 Use of this product can contribute towards LEED v3certification:Up to 2 points towards MR Credit 5, Regional MaterialsUp to 2 points towards MR Credit 4, Recycled ContentUp to 1 point towards IEQ Credit , Low Emitting Materials Adhesives & Sealants5 InstructionsGeneral Surface PrepUSE CHEMICAL-RESISTANT GLOVES, such as nitrile, whenhandling must be structurally sound. Remove all grease, oil, dirt,curing compounds, sealers, adhesives or any other contaminant thatwould prevent a good bond. Glossy or painted surfaces must besanded, or abraded, and stripped of all contaminants. Concrete mustbe cured 28 days and accept water penetration. Concrete must be freeof efflorescence and not subject to hydrostatic pressure.

6 Concreteslabs should have a coarse finish to enhance the bond. Plywoodflooring including those under resilient flooring must be structurallysound and meet all ANSI and deflection requirements. For questionsabout proper subfloor installation, call Technical Services. Smoothconcrete surfaces, existing glazed tile, terrazzo, or polished stoneshould be scarified. sheet vinyl must be well bonded and stripped ofold finish. Roughen the surface by sanding or abrading, then rinse andallow to dry. Expansion joints should never be bridged with settingmaterial. Do not sand flooring materials containing asbestos. Ambienttemperature should be maintained above 50 F (10 C) or below 100 F (38 C) for 72 hours to achieve proper bond.

7 Bonding to Concrete SurfacesConcrete or plaster must be fully cured and must accept waterpenetration. Test by sprinkling water on various areas of the water penetrates, then a good bond can be achieved; if waterbeads, surface contaminants are present, and loss of adhesion mayoccur. Contaminants should be mechanically removed beforeinstallation. Concrete must be free of efflorescence and not subject tohydrostatic pressure. Concrete slabs should have a coarse finish toenhance the bond. Smooth concrete slabs must be mechanicallyabraded to achieve proper to Lightweight cement and Gypsum SurfacesLightweight or gypsum based underlayments must obtain a minimum2000 psi ( MP) compressive strength. The underlayment must besufficiently dry and properly cured to the manufacturer s specificationsfor permanent, non-moisture permeable coverings.

8 Surfaces to betiled must be structurally sound and subject to deflection not to exceedthe current ANSI Standards. Surfaces shall be free of all grease, oil,dirt, dust, curing compounds, waxes, sealers, efflorescence, or anyother foreign Lightweight cement or Gypsum surfaces should be primed with aproperly applied sealer or a primer coat of RedGard, consisting of 1part RedGard diluted with 4 parts clean, cool water. Mix in a cleanbucket at low speed to obtain a lump free solution. The primer can bebrushed, rolled or sprayed to achieve an even coat. Apply the primercoat to the floor at a rate of 300 sq. ( sq. m/L). Drying timedepends on site conditions, but is normally less than 1 hour. Extremelyporous surfaces may require 2 coats.

9 At this point, RedGard can beapplied to the primed lightweight or gypsum based surface. Refer tothe individual product data sheet or packaging directions for applicationinstructions. Expansion joints must be installed in accordance with localbuilding codes and ANSI/TCNA guidelines. Refer to TCNA to Plywood SurfacesPlywood floors, including those under resilient flooring, must bestructurally sound and must meet all ANSI Part Maximum allowable deflection: L/360 tile L/720 TCNA F150-13 Tile Installations, TCNA F141-13 and F250-13 forStone. For questions about proper subfloor installation requirements,call Custom technical Professional Thin Set MortarPublished Date: 3/27/2018 VersaBond Professional Thin Set Mortar / TDS 119 Bonding to BackerboardsAs an alternative to an additional layer of plywood, WonderBoardbackerboard may be installed over plywood subfloors for ceramic tileinstallations.

10 Refer to TCNA F144-13 tile installations, TCNA F250-13stone installations. Call Custom technical services when installingnatural stone over plywood to Existing Surfacing MaterialExisting Ceramic Tile, Resilient Flooring or Plastic Laminates: Resilientflooring or plastic laminates must be well bonded, as well as clean andfree of all contaminates. Roughen the surface by sanding or scarifying;rinse and allow to dry. Do not sand flooring that contains asbestos. Forexisting well bonded ceramic tile, mechanically abrade the and allow to dry. When sanding, an approved respirator shouldbe to Cutback AdhesiveAdhesive layers must be removed, as they reduce mortar bondstrength to cement surfaces. Use extreme caution; adhesives maycontain asbestos fibers.


Related search queries