ABS submersible sewage pump XFP 100J - 501U

1 ABS submersible sewage pump XFP 100j - 501 UABS submersible sewage pumps , series XFP are suitable for clear water and wastewater, for sewage containing solids and fibrous material. Performance curves with Contrablock systemMotorWater pressure sealed premium efficiency motors, (3-phase, squirrel cage induction motors), from 23 to 168 hp and, depend-ing on hydraulic requirements as 4- to 10-pole versions. Voltage: 460 V3~, 60 Hz (other voltages on request).Insulation material: H (motor winding protected by temperature sensor 284 rise: According to class type: : direct on line (DOL), soft starter or Energy saving premium efficiency motor in accordance withIE3 of IEC 60034-30 and NEMA Premium Efficiency. The water-tight, fully flood-proof motor and the pump sectionform a compact and robust unit, easy to clean and easy to service. Water pressure sealed connection chamber, with two stagecable entry, protected against excessive cable tension and bending.)

2 Bimetallic thermal sensors in the stators which open at 284 F. Rotor and rotor shaft dynamically balanced, upper and lowerbearings lubricated-for-life, maintenance-free. Triple shaft sealing. Upper and lower sealing by means of silicon carbide mechani-cal seal, independent of the direction of rotation. Inspection chamber with sensor for moisture protection toindicate water leakage through mechanical seal, also standard for ex-version, according to FM and CSA approval. Optional: Maintenance-free internal looped cooling system. Cooling medium: non toxic Glycol - water mixture. 2 or 3-channel Contrablock or 2- or 3-channel closed impellerdesigns. Standard in explosion-proof construction in accordance withinternational standards such as 500 Class I, Division 1, Groups C and D hazardous (classified) have the choice of the following hydraulics in the range of 4 to 20 in discharge:60 HzPerformance curves with channel impeller60 HzXFP 100 JCB2 XFP 250 JCB2 XFP 100 JCH2 XFP 250 MCH2 XFP 150 MCB2 XFP 300 JCB3 XFP 150 JCH2 XFP 300 JCH2 XFP 151 JCB2 XFP 300 MCH2 XFP 200 JCB2 XFP 301 MCH2 XFP 200 JCH2 XFP 351 MCH3 XFP 200 MCH2 XFP 400 MCH2 XFP 201 JCB2 XFP 501 USK3 Hydraulics / Impeller = Contrablock, = closed channel, SK = Skew;last digit (2 or 3) = Number of impeller vanesABS submersible sewage pump XFP 100j -501U 60 Hz GB ABS reserves the right to alter specifications due to technical ambient temperature104 F140 FMax.

3 Submergence depth65 ftMains voltage460 V/60 Hz230 V, 380 V, 575 V, 600 V/60 Hz Voltage tolerance 10 % at 460 VInsulation classH (140)H (160) (not for explosion-proof)Start-upDOL (direct on line), soft starter, or VFDA pprovalNEC Class I, Division 1, Groups C and DCablesS1BN8-FEMC shielded cablesCable length33 ft19 ft, 65 ft, other length on requestMechanical seal (medium side)SiC-SiC (NBR)SiC-SiC (Viton execution)Mechanical seal (motor side)SiC-SiCO-ringsNBRV itonPreparation for lifting hoistLifting hoopLifting hoop in stainless steelProtective coatingTwo component coating epoxy resinSpecial coatings on requestCathodic protectionZinc anodes on requestInstallationWet-wellDry-well vertical/horizontalMotor coolingCooling by surrounding mediumClosed loop cooling systemMoisture sensor motor housingDI (sensor for moisture detection)Moisture sensor inspection chamberDI (sensor for moisture detection)Standard and optionsMaterialsMotorStandardOptionConne ction chamberEN-GJL-250 Cooling chamberEN-GJL-250 Cooling housingEN-GJL-250 Motor (medium contacted) hoopEN-GJS-400-18 plate (not all versions) EN-GJL-250 Shroud (only XFP 501)EN-GJL-250 Wear ring (not all versions) protectionPE4 and PE5 ExEx VFD driveWindingBi-metallic switchXXThermistor (PTC)OOPT 100 OOSeal protectionInspection chamberXXMotor housingOOConnection boxOOTemperature bearing upper/lowerBi-metallic switchOOThermistor (PTC)OOPT 100 OOABS USA , 140, Pond View Drive, CT 06450, USA Tel +1 203 238 2700, Fax +1 203 514 = Standard, O = OptionConnection sys.

4 (wet)StandardOptionPedestalEN-GJL-250 Non sparkingFastening elementsStainless steelProtective coatingEpoxy resinGuide railGalv. steelStainless steelPipe sys. (dry)StandardOptionSupport steelMaterial comparisonEuropeUSAEN 1561; EN-GJL-250 ASTM A48; Class 35 BEN 1563; EN-GJS-400-18 ASTM A536; 60-40-181623-2; ; S235 JRG1 ASTM / AISI A283 (C) / AISI ; / AISI 316; 329