ADVANCES in PRODUCTION, - wseas.org

1 ADVANCES in production , AUTOMATION and TRANSPORTATION SYSTEMS Proceedings of the 6th International Conference on Manufacturing Engineering, Quality and production Systems (MEQAPS '13) Proceedings of the 4th International Conference on Automotive and Transportation Systems (ICAT '13) Brasov, Romania June 1-3, 2013 Scientific Sponsors: Transilvania University of Brasov University of Craiova University Politehnica of Bucharest Stefan cel Mare Universtity of Suceava Constantin Brancusi University of Targu-Jiu Megatrend University of Belgrade University Lucian Blaga of Sibiu Constanta Maritime University Mathematics and Computers in Science and Engineering Series | 13 ISSN: 2227-4588 ISBN.

2 978-1-61804-193-7 ADVANCES in production , AUTOMATION and TRANSPORTATION SYSTEMS Proceedings of the 6th International Conference on Manufacturing Engineering, Quality and production Systems (MEQAPS '13) Proceedings of the 4th International Conference on Automotive and Transportation Systems (ICAT '13) Brasov, Romania June 1-3, 2013 Published by WSEAS Press Copyright 2013, by WSEAS Press All the copyright of the present book belongs to the World Scientific and Engineering Academy and Society Press. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the Editor of World Scientific and Engineering Academy and Society Press.

3 All papers of the present volume were peer reviewed by no less that two independent reviewers. Acceptance was granted when both reviewers' recommendations were positive. See also: ISSN: 2227-4588 ISBN: 978-1-61804-193-7 ADVANCES in production , AUTOMATION and TRANSPORTATION SYSTEMS Proceedings of the 6th International Conference on Manufacturing Engineering, Quality and production Systems (MEQAPS '13) Proceedings of the 4th International Conference on Automotive and Transportation Systems (ICAT '13) Brasov, Romania June 1-3, 2013 Editors: Prof. Vladimir Marascu-Klein, Transilvania University of Brasov, Romania Reviewers: Rosli Abu Bakar Mohammad D.

4 Al-Tahat Mihaiela Iliescu C. Buzatu Gh. Oancea Adina Andreea Ohota Elena Scutelnicu Mustafa Yagimli Roots Larissa Yuqing Zhou Shiang-Yen Tan Santoso Wibowo Valentina E. Balas Sorin Ioan Deaconu Ankit Patel Aamir Saeed Malik Ana Pilipovic Stavros Ponis Mihai Timis Ioan Susnea Hung-Jen Yang Alina Adriana Minea Sorin Gherghinescu Radha Gupta Zengshi Chen Ali Hennache A. Nedelcu Stefan Ghimisi Masaji Tanaka Ki Young Kim Surojit Ghosh Nikos Loukeris Hugo Rodrigues Paulo Avila Srdjan Bosnjak Sorinel Oprisan L. Dimitrov Md. Jakir Hossen Rocco Furferi Calin Ciufudean Roman Mihai Daniel Arion Felix Abd Rahim Abu Bakar Ioana Adrian Georgel Chirita Mehdi Safari Jo o Bastos Poom Kumam Nayan Kumar Hamidreza Hoshyarmanesh Vasile Cojocaru Tohru Kawabe Al Emran Ismail Matteo Palai Vassos Vassiliou Morale Terry Muhammad Musaddique Ali Rafique Chandrasekaran Subramaniam Cristian Silviu Simionescu Mohammad Israr Chandrasekaran Manoharan Grabara Janusz Ming-Shen Jian Eleazar Jimenez Serrano Hamid Bashiri Atrabi N.

5 B. Lupulescu Krisztina Uzuneanu Jianfu Du Chunwei, Lu Wini Lu Gabriela Mircea Mariya Aleksandrova Alexandru Filip Ionel Botef Alejandro Fuentes-Penna U. C. Jha Hakan Tozan Catalin Popescu Lapo Governi Mohamed Hussein Doru Nicola Konstantin Volkov Libor Pekar M. M. Noor Table of Contents Plenary Lecture 1: Excel Workbook for Convenient Scheduling of Job-Shop production Projects13 Madalin Catana Plenary Lecture 2: Study Concerning the Possibilities of Self-Starting of Induction Motors 14 Flavius Dan Surianu Plenary Lecture 3: A Study on Centerless Grinding 15 Nicolae-Doru Stanescu Plenary Lecture 4: Human Factors Approach in Drilling Rigs Monitoring and Personnel Training 16 Sorin Dan Grigorescu Plenary Lecture 5.

6 Strategies Regarding Development of Road Transport to Diminish Greenhouse Gas Emissions 17 Corneliu Cofaru 3-D CAD Modeling and Analysis of Aircraft Wing Using CATIA Software and its Comparison with ANSYS Software 19 Hassan Naseem Khan, M. Wahab Usama, Riaz Ahmad, Iqbal Rasool Aspects Regarding Energy Efficiency of Refrigeration System Associated to the Fruit and Vegetable Processing Industry 23 Feiza Memet, Daniela Elena Mitu A Point of View in Study of Noise Level and Vibrations on an Ice Breaking Tug using Time Method and FFT Analysis 28 Daniela Elena Mitu, Feiza Memet Propeller Excitations Inducted to the Shafts of the Naval Engine 38 Liviu Constantin Stan Cryogenics Applications in the Maritime Field 42 Liviu Constantin Stan, Daniela Elena Mitu Aspects Concerning the Automation of the Mechanical Expansion Process for Large Welded Pipes 47 Tudor Macrea, Dorian Macrea, Costin Cepisca.

7 Sorin Dan Grigorescu, Horia Andrei, Marian Morcovescu Economic Lot Sizing for a Multi-Operation Machining Process Allowing for Parts Transportation Cost 51M d lin Catan , Sergiu Tonoiu ADVANCES in production , Automation and Transportation SystemsISBN: 978-1-61804-193-77 Cutting-Edge Actuating Systems of the Upper Limb Rehabilitation Devices 55 Ovidiu Filip, Tudor Deaconescu The Quality of Deep Drilling Process by Roughness s Contact Measurement 60 Laurentiu-Aurel Mihail Study on the Pneumatic Actuation of Gripping Systems 66 Doina rliman Negrea, Tudor Deaconescu Research on Modeling in Case of Longitudinal Beech Wood Processing with Circular Saws 71 Cosmin Spirchez, Loredana Anne-Marie Badescu Analysis of Process and Product Quality Assurance 75 Florina-Cristina Filip, Vladimir Marascu-Klein Simultaneous Optimization of Preventive Maintenance and Replacement Policy in Systems 82 Daiana Maria Tont, Gabriela Tont.

8 Dan George Tont Analysis of the Calculus Relations of the Cutting Forces and Moments at Drilling of the Stainless Steel X20Cr13 88 Ovidiu Bl jin , Aurelian Vlase Mathematical Simulation of the Results of Temperature Measurements at the Machining of the Polymeric Composites Materials 94 Paulina Sp nu, Tom Savu, Bogdan Abaza, Daniel Cazacu Determination of Hygroscopicity of Composite Materials Used in Furniture Industry 100B il Diana-Irinel, Tonoiu Sergiu, Catan M d lin, Laz r Livia Corrective Action Documented Procedure Applied in a Medium Sized Company 106 Laz r Livia-Veronica, B il Diana-Irinel Internal Audit Documented Procedure Applied in a Medium Sized Company 109 Laz r Livia-Veronica, B il Diana-Irinel Product s Structure Representation and Activities Simulation in a Manufacturing System Simulation Framework 113 Tom Savu, Bogdan Abaza, Paulina Sp nu, Daniel Cazacu Decision Making using the Analytic Hierarchy Process 119 Gabriel Iulian F nt n , Stefan Adrian Oae, Andrei Marian Gurau The Dependence of Cutting Force upon 17-4 PH Machining Parameters 125 Popovici Tabita-Dana, Grigorescu Mihai The Influence of Cutting Parameters on the Durability of Carbide Tools in Internal Finishing Turning of Inconel 718 Parts 129 Ion Ciocan.

9 Tabita-Dana Popovici ADVANCES in production , Automation and Transportation SystemsISBN: 978-1-61804-193-78 Simulation Techniques in CAD-CAM Processing by Milling of Surfaces on NC Machine-Tools 135 Ghionea Ionut, Ghionea Adrian Research on Regression Models of Force in Drilling Mineral Composite Material 2% Glass Fiber Reinforced 141 Mihaiela Iliescu, Alexandru P tra cu Study Concerning the Possibilities of Self-Starting of Induction Motors 147 Flavius Dan Surianu Process Quality Control Aspects in Turning S12Mn2Si Thermal Sprayed Coatings 153 Mihaiela Iliescu, Rodica Rohan Ecotechnological Aspects of Automobile Recycling 159 Gheorghe Amza, Zoia Apostolescu, Mihaiela Iliescu, Garac Zlatko.

10 Marius Cornel Teodorescu The Elaboration of a Methodology for the Calculation of the Chains of Sizes with Help C++ 165 Constanta R dulescu, Liviu Marius C rt n Unsteady Flow over a Bluff Body with Application in Unconventional Propulsion System 173 Andrei Alexandru Scupi, Dumitru Dinu Distance against Competitors from the Field of Concentrated Energies Technologies Evaluated through Elements of Customer Matrix 178 Daniel Ghiculescu, Niculae Marinescu, Daniela Ghiculescu, George Seritan Development of a Magnetostrictive Vibromotor 184 Ilie Romaniuc Considerations on the Thin Layers Deposition through Metallization in Plasma Jet 188 Mircea Viorel Dragan, Marian Bordei, Ioana Diaconescu, Aurel Ciurea Application of Lean Concept in Optimization of Manufacturing Systems 194 Adriana Fota Determining of Hardness for Superficial Layers Obtained through Electrical Sparking 198 Barhalescu Mihaela Luminita Roughness Variation and Deviation from the Perpendicularity of High Concentrated Ceramic Alumium Oxide on Linear Cutting in Abrasive Jet Machining Technology 201 Alexandru C t lin Filip, Horatiu Bulea The Pyrography, from Solar Radiation to Laser Radiation 206 Adrian Petru, Aurel Lunguleasa Contributions of Profiled Continuous Relieving Tools 210 Gheorghe Mare ADVANCES in production , Automation and Transportation SystemsISBN.