AirBeam User guide - vangoairbeam.com

1 GuideUser guide Contents Page 1. Introduction to Vango AirBeam P3 2. FAQ s P4-5 3. Vango AirBeam support & other information P6-10 Steps to check a deflating AirBeam How to check for punctures We make every effort to ensure the accuracy of our information. We do however have a policy of continuous improvement and we therefore reserve the right to change or amend colours and specifications without prior notice. *Last updated February 01/02/13 2 user Guide3 1. Introduction to Vango AirBeam Successfully launched in 2011, Vango AirBeam is revolutionary in its design and structure and is set to change the face of camping! The tents use inflatable beams in place of traditional steel poles for rapid pitching in any environment.

2 Pitching time takes only 3 to 10 minutes depending on the size of the tent and will be up and ready to go in 4 easy steps. All you have to do is take the tent out of the bag, pop a peg in each corner, pump up the inflatable beams and peg down a few guylines. It really is that simple!2. FAQ sVango AirBeam looks so simple, what is the catch? No catch, just simple, quick and easy to pitch!Where can I find pitching instructions or videos?Pitching instructions are available for each type of Vango AirBeam tent and can be found at it difficult to deflate and put away? The deflation and take down process of the Vango AirBeam is very easy. Simply unscrew each valve to release the air and allow it to deflate size is the pump that comes with the tent? For all Vango AirBeam models there is two different pump sizes.

3 If you have a Flux, Velocity, Genesis, or Pulse then it will have a 1400cc size and for the Infinity, Kinetic, Eternity, Exodus, Evoque, Utopia and Shangri-La these will have a 2000cc pressure should I inflate my Vango AirBeam to?You should inflate the AirBeam to 7psi. If you have a 2011 model then inflate the AirBeam to 3psi. A free upgrade to a 3rd generation AirBeam is now available to all customers with a 2011 model. Can I get a free upgrade for my 2011 AirBeam outer sleeve?New Vango AirBeams have been fitted with significantly stronger outer sleeves to withstand the daily rigours of family camping. These new outer sleeves are now available, as a free upgrade, to consumers who purchased a 2011 edition of the following Vango AirBeam tent models: Product Description Product Code Infinity 600 TEFINFINII36181 Infinity 800 TEFINFINII36184 For further details please visit: Can I use any hand / foot pump to inflate the Vango AirBeam ?

4 No, you can only use a hand/foot pump that fits the valves in the tent. Bicycle, car, foot and hand pumps will not normally fit and are not I use an electric pump to inflate my Vango AirBeam ? It is very quick and simple to use the double action pump supplied. A specific AirBeam pump is in development. No other pumps should be used as they may be too powerful and damage the AirBeam .42. FAQ sVango AirBeam looks so simple, what is the catch? No catch, just simple, quick and easy to pitch!Where can I find pitching instructions or videos?Pitching instructions are available for each type of Vango AirBeam tent and can be found at it difficult to deflate and put away? The deflation and take down process of the Vango AirBeam is very easy. Simply unscrew each valve to release the air and allow it to deflate size is the pump that comes with the tent?

5 For all Vango AirBeam models there is two different pump sizes. If you have a Flux, Velocity, Genesis, or Pulse then it will have a 1400cc size and for the Infinity, Kinetic, Eternity, Exodus, Evoque, Utopia and Shangri-La these will have a 2000cc pressure should I inflate my Vango AirBeam to?You should inflate the AirBeam to 7psi. If you have a 2011 model then inflate the AirBeam to 3psi. A free upgrade to a 3rd generation AirBeam is now available to all customers with a 2011 model. Can I get a free upgrade for my 2011 AirBeam outer sleeve?New Vango AirBeams have been fitted with significantly stronger outer sleeves to withstand the daily rigours of family camping. These new outer sleeves are now available, as a free upgrade, to consumers who purchased a 2011 edition of the following Vango AirBeam tent models: Product Description Product Code Infinity 600 TEFINFINII36181 Infinity 800 TEFINFINII36184 For further details please visit: Can I use any hand / foot pump to inflate the Vango AirBeam ?

6 No, you can only use a hand/foot pump that fits the valves in the tent. Bicycle, car, foot and hand pumps will not normally fit and are not I use an electric pump to inflate my Vango AirBeam ? It is very quick and simple to use the double action pump supplied. A specific AirBeam pump is in development. No other pumps should be used as they may be too powerful and damage the AirBeam .Can I use a compressor? No, it is recommended to use the Vango AirBeam pump the AirBeam valves be replaced? Vango AirBeam valves are available from AMG Group Services (see the back of this booklet for contact details). The correct AirBeam valve for each model will be sent I get a replacement or spare AirBeam ? AirBeams are available from Will the Vango AirBeam be able to withstand high winds? Yes, there are no poles to snap and all models use Vango s patented TBS II system for additional stability in windy conditions.

7 These tents have been tested in extreme conditions in our wind certified test centre with speeds of up to 100 the Vango AirBeam canopy fit onto a caravan, campervan or motorhome? A Vango Air Away Awning range is being launched this year. The Vango Air Away is a drive away awning that uses Vango AirBeam technology for rapid pole free pitching. More details can be found at Vango AirBeam support & other information Steps to check a deflating AirBeam (Any inflatable device such as dinghies, airbeds etc are all affected by temperature and humidity and should be regularly checked to ensure that they contain the correct pressure. If your AirBeam is not maintaining the correct pressure, please follow these simple steps to resolve the issue).A Deflate the AirBeam fully by completely unscrewing both parts of the valve.

8 B Check the threads of all AirBeam valve parts are clean and free from Check the 3 black rubber parts within the AirBeam valve are still in E Screw in the base of the AirBeam valve ensuring that no fabric is caught between the two parts of the Ensure that the AirBeam valve is screwed in correctly and not cross threaded (a small amount of Vaseline or lip balm can be applied to the valve to help the valve screw in easily).G Inflate the AirBeam to 7psi for 2012 models onwards. If you have a 2011 model then inflate the AirBeam to 3psi. A free upgrade to a 3rd generation AirBeam is now available to all customers with a 2011 model. To find out if you qualify please visit 6H Note: Velocity and Infinity tents purchased in 2011 should continue to use 3 Screw the AirBeam valve cap into position and tighten fully.

9 J If the AirBeam continues to deflate then the inner TPU tube should be removed and checked for punctures (see page 5 for instructions). Note: Small punctures can be fixed using the repair kit included with the tent or Tear Aid patches (see page 5 for instructions). If there is a major fault on the inner TPU then this can be replaced by AMG Services (email details of year, model and TPU tube are required and contact details can be found at the back of this guide ).7 How to check for punctures and repair the inner TPU tubeK Deflate the AirBeam fully by completely unscrewing the valve. Note: The pump cannot be used to deflate the AirBeams .L Unzip the outer sleeve of the AirBeam .M Remove the AirBeam from the internal zipped Cut the cable tie that holds the zips together (to stop accidental opening).

10 8O Remove the inner TPU tube from it s protective Put a very small amount of air into the tube to allow you to check for the puncture. NOTE: Take care not to add too much air into the tube as the TPU material can be damaged if inflated outside of the zipped To find a leak, check this by using a basin of Once the puncture is located then the area around this should be cleaned, ensuring it is dry, free from debris and Carefully apply the repair patch over the puncture, and rub until it is fully stuck. T Allow to dry for 30 minutes. 9U Place the inner TPU tube back inside the protective outer taking care not to catch the TPU tube in the zip (if possible connect the zips together again, so that they cannot be accidentally opened when the AirBeam is inflated).V Re-inflate the AirBeam to the correct psi level depending on which tent model it Re-insert the AirBeam into the zipped sleeve on the tent flysheet.