AMX SERIES INSTALLATION AND OPERATION …

1 REV. GLASS AND DISHWASHERS AMX SERIES INSTALLATION AND OPERATION instructions HOBART FOOD EQUIPMENT CO., LTD 1208 AMX OPERATION INSTRUCTION 2 Translation of the original instructions This guide does not apply to physical, sensory or mental defective, or there is a lack of experience and knowledge of people (including children) As continued product improvement is a policy of HOBART, specifications are subject to change without notice. Company address Yesheng Road, Xiqing Economic & Development Zone, Tianjin China 3 Content 1 Important Notes.

2 4 2 Brief Introduction .. 5 3 INSTALLATION .. 6 and .. 6 Location .. 6 Converting to corner OPERATION .. 6 Electrical connection .. 7 connection .. 8 Drain connection .. 9 4 Connecting external dispensers .. 10 5 Controls .. 11 6 Start-up .. 12 Detergent / rinse aid .. 12 Priming the suction hoses .. 12 Softener (only on option) .. 13 7 OPERATION .. 14 Preparation .. 14 Run .. 14 Program selection .. 16 8 Switch-off and cleaning the machine .. 17 Switch-off .. 17 Cleaning (daily) .. 17 Cleaning (weekly) .. 17 9 Preview of temperatures .. 18 10 Faults.

3 18 11 Settings and Counter values .. 20 Adjustment of detergent dosage quantity .. 20 Adjustment of rinse aid dosage quantity .. 20 Adjustment of water hardness .. 20 Cycle counter .. 21 Water consumption counter .. 21 Remaining water quantity counter for external water treatment .. 21 Activation / deactivation of chemicals deficiency sensors .. 21 Termination of setting mode / counter display .. 21 12 Frost prevention .. 22 13 Maintenance .. 22 14 Troubleshooting guide .. 22 15 EC Declaration of Conformity ..24 AMX OPERATION INSTRUCTION 4 1 IMPORTANT NOTES Use in Accordance with Regulations This machine is exclusively to be used to wash ware such as plates, cups, glasses, cutlery, trays etc.

4 Do not use for electrically heated cooking and heat conservation appliances. Safety The "Attention" symbol is shown beside instructions that are essential for the safe OPERATION of the machine. Please read these passages thoroughly. Liability Installations and repairs which are carried out by non authorized technicians or the use of other than original spare parts, and any technical alterations to the machine, may affect the warranty set out in the standard conditions of sale. The machine can be used by one person only, does not allow two or more people operate at the same time. Machine noise level: The machine noise level 70 dB (A).

5 Unpacking: Immediately after unpacking, check for possible shipping damage. If the dishwasher is found to be damaged, save the package materials and contact the carrier within 15 days of delivery. Please take out parts of scene INSTALLATION , manuals and maintenance card. Please fill out necessary information carefully. NL 5 2 BRIEF INTRODUCTION Hood type dishwasher for straight through or corner OPERATION , capacity 60 racks, 1080 plates or 2160 glasses per hour. Product Advantages: z ready to install, incl. fill and drain hoses, power cord, non return valve z completely equipped with rinse pressure pump, drain pump and optional agent dispenser z optimum service accessibility z optimum hygienic safety by deep drawn tank with rounded edges and self cleaning cycle z hood closed on all sides z electronic control with color coded status indication and ergonomic position of the control panel z GENIUS-X fine filter system: achieving better wash results due to permanent filtration of wash water-saving energy and detergent Option.

6 Tabling Technical Data Flexible drain hose 1500mm 24mm inner/28mm outer Fresh water connection pressure hose 1500mm Flow pressure R 3/4 inside Max60 C Power cord 2500mm Hoses for Detergent(option) Aid rinse agent 1600mm each (if required)Cycle times 60 sec 90 sec 120 sec Water consumption L/rackTank capacity 22L Tank heating 3kw Power supply 380/50/3/NBooster loading 12kw Total loading 16kw/3X24 APump capacity Loading height 440mm Noise level 70dB(A) Weight net AMX OPERATION INSTRUCTION 6 3 INSTALLATION Transportation and storage Forklift must be used during transportation and storage instead of vertical loading, pay attention to upturn and prevention of break moisture and load.

7 (See the marks on the package. Location - Rear wall clearance not required. For corner INSTALLATION lateral clearance of 107 mm is required. INSTALLATION should comply with all national and local appropriate codes at practice. For free-standing INSTALLATION the optional rear panel has to be installed. Level machine by turning the feet. Distribute machine weight equally onto all feet. Converting to corner OPERATION Depending on direction of OPERATION , the guide rails may need to be adjusted to suit the direction of OPERATION (see arrows). - Unscrew the guide rail in front. - Refit guide rail at right angle according to the direction of OPERATION .)

8 7 Electrical connection Must be carried out by an authorized technician according to the local and national codes. A fused disconnects or circuit breaker with electrical leaking protector (not supplied) must be installed in the electrical line supplying the dishwasher and should meet the requirements of your local electrical code. - The electrical supply shall comply with the name-plate data. - Line fuses and cable cross section shall comply with the requirements. - A cut-off device shall be provided to connect the supply cord (isolating switch or accessible plug device). - Remove the front panel and two side panels.

9 - Let the power cable thread the cable bushing on the base plate. - Fix the cable via the control box. AMX OPERATION INSTRUCTION 8 - Connect the power cable to terminals on the control board according to the picture. - Replace the front panel and side panels. According to EN 60 33 5 the appliance must be connected to an equipotential conductor. The connecting screw ( ) is located beside the cable inlet. Water connection Must be carried out by an authorized technician according to the national and local codes. The machine must be operated with potable water.

10 For water with an extremely high mineral content an external demineralizer strongly recommended. - Machines without softener: Connect to soft and if possible warm water (up to 4 Clark = mmol/l, max. 60 C). Important: The water hardness should be If not, water softener is strongly recommended. Or else, may affect the warranty set out in the standard conditions of sale. - Machines with softener: Connect to warm water (max. 60 C) if possible. - Line flow pressure 10 bar. Important: the line flow pressure must not be less than bar. - If the line flow pressure is above 10 bar provide pressure reducer at source.