Analog Mode - .NET Framework

1 Analog Mode INSTALLATION GUIDEThis product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and 02-25 2019 Directed, Vista CADS4+Designed by Installers for InstallersContentsWarning! Safety first ..3 Introduction ..4 Pre-installation and application warnings ..4 System compatibilities ..4 What you get ..4 Main module connections ..5 Installation ..6 Wiring connections ..7 Main harness (H1), 12-pin black connector ..7 Relay harness (H2), 10-pin white connector ..7 Data harness (H3), 8-pin white connector ..7 Analog input /output harness (H4), 22-pin white connector ..8RF Port harness (H5), 2-pin white connector.

2 8D2D harness (H6), 4-pin white (1) and black (2) connectors ..8 Temperature sensor harness (H7), 2-pin black connector (optional, 8556T) ..8 Configuring the ! ..9RF Systems ..98504D Combo Sensor ..9 When used in conjunction with SmartStart ..9D2D port configuration ..10 Module programming ..10 LED diagnostics and troubleshooting ..10 Hard reset ..11 Initializing Virtual Tach: ..11 Remote start shutdown/startup diagnostics ..12 Shutdown diagnostics ..12 Startup diagnostics ..12 Remote management ..12 Long-term event history (when security features are enabled) ..13 Table of zones ..13 Troubleshooting ..14 Alarm (when security features are enabled) ..14 Remote start ..14 Glossary of terms ..16 Limited lifetime consumer warranty ..17 Quick Reference Guide ..183DS4+ Analog Mode (Viper & Automate) 2019-02-25 Directed.

3 All rights ! Safety firstThe following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE.

4 ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide.

5 If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake.

6 Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain + Analog Mode (Viper & Automate) 2019-02-25 Directed. All rights DS4+ is a complete solution for remote start, security (when security features are enabled), bypass and features built in Bluetooth allowing you to configure and control your system. This guide provides information on the installation of the module as an Analog unit, however a digital solution could be available for your vehicle. Please refer to the DirectLink application or for more information about which configuration is best for your ! This module is designed to be configured using the DirectLink application for mobile devices, however it can also be configured using the web tool located at To download the DirectLink mobile application, please visit the Google Play or Apple and application warningsFirmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle compatible Keys required for programmingN/AKeys required for operationN/A It is important to check that the fuses are positioned correctly in the module.

7 Refer to the Analog installation "Wiring diagram" for fuse selection notes: This section highlights important information for this specific firmware.[1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin.[2] The siren is ONLY required when enabling the security features during module flashing.[3] The Green wire is ONLY required for starter disable and antigrind applications.[4] (+) or (-) depending on positioning of the on-board compatibilitiesFor further information on the products listed below, refer to the corresponding start, lock and unlock your car by only pushing a button on your mobile device; using the simple graphical interface of the Directed SmartStart SystemsAn RF System consists of one or multiple remotes, a Control Center (antenna), and an antenna cable various combinations exist.

8 An RF System allows the vehicle owner to control the system with enhanced range. Two-way models are available. Please follow the instructions included with the kit for appropriate installation and programming information. What you getWelcome to the best generation of security and remote start. Your system contains everything you need to get started. DS4/DS4+ main module. Main and secondary harness kits. Output harness. Safety kit (hood pin). Introduction : Depending on the system purchased, it may be equipped with an RF System, a siren or a combo + Analog Mode (Viper & Automate) 2019-02-25 Directed. All rights module connections228101242442DS4+DS4 Transponder RF Loop Connector (optional) (H5)2 pins, WhiteAnalog input /Output Connector (H4)22 pins, WhiteData Connector (H3)8 pins, WhiteMain Connector (H1)22 pins, BlackHigh Current Relay Connector (H2)*10 pins, WhiteDS4+ Programming Button(Used to reset & program the firmware)DS4 Programming Button(Used to reset & program the firmware)D2D 3 for Control Center, Combo Sensor or 3rd Party Bypass Connector (H6)4 pins, BlackD2D 2 for Control Center, Combo Sensoror 3rd Party Bypass Connector (H6)4 pins, BlackD2D 1 for SmartStart, Control Center,Combo Sensor or 3rd Party Bybass Connector (H6)4 pins, WhiteTemperature Sensor Connector (optional, 8556T) (H7)2 pins, Black* DS4+ ONLY.

9 Certain vehicles may require high current outputs for remote start + Analog Mode (Viper & Automate) 2019-02-25 Directed. All rights diagram below lists the wires that are common to most vehicle installations. See "Wiring connections" on page 7 for more specific wiring ! It is important to check that the fuses are positioned correctly in the module to avoid module or vehicle +DS4(+) 12 Volt input (Flex relay): Red/White: 9 Relay - (+) Starter Output (vehicle side): Violet: 7 Relay COM - (+) Ignition Output: Pink: 10(-) Ground: Black: 10 Relay COM - (+) Accessory Output: Orange: 8 (+) 12 Volt input (Accessory/Starter relay) input : Red/Black: 2 Relay COM - (+) Flex Relay Output: Pink/White: 4 Relay - (+) Flex Relay Isolation: Pink/Black: 3(+) 12 Volt input (Ignition relay): Red: 5(+) 12V: Red: 6 & 12 Relay 3 COM - Parking Light Output: White: 5 & 11 Relay 1 - Status Isolation, pin 87a: Blue/White: 1 Relay 1 - Status input , pin 87: Blue/Red: 2 Relay 1 COM - Status Output, pin 30: Blue.

10 3 Relay 3 - Parking Light Isolation: White/Brown: 4 Relay 2 - Trunk Release input , pin 87: Lt. Green/Red: 7 Relay 2 COM - Trunk Release Output, pin 30: Lt. Green: 8 Relay 2 - Trunk Release Isolation, pin 87a: Lt. Green/White: 9 Relay COM - Starter input (connector side): Green: 6(-) Factory Alarm Arm Output: Lt. Green/Black: 1(-) Factory Alarm Disarm Output: Lt. Blue/Black: 10(-) E-Brake input (manual trans.): Black/White: 17(+) Instant Trigger input : Orange/Black: 18(-) Trunk Trigger input : Blue: 19(-) Hood Trigger input : Gray: 21(AC) Tach input : Violet/White: 22(-) Unlock Output: Blue/Black: 9(-) Horn Output: Brown/Black: 5(-) AUX 1 Output: Brown/White: 6(+) AUX 1 Output: White: 7(+) AUX 2 Output: Violet/Black: 8(-) Trunk Release Output: Red/White: 4(-) Door Trigger input : Green: 20(+) Door Trigger input : Violet: 13(-) Lock Output: Green/Black: 3(+) Brake input : Brown: 14(-) Activation input : White/Blue: 15(-) Headlight Detection input : Red/Blue: 16(+) Siren Output: Brown/Red: 11(+) Ignition Sense input : Pink.