Aruba 3810M Switch Series Installation and Getting Started ...

1 Aruba 3810M Switch SeriesInstallation and Getting Started GuidePart Number: 5998-8461bPublished: May 2020 Edition: 3 Copyright 2016, 2020 Hewlett Packard Enterprise Development LPNoticesThe information contained herein is subject to change without notice. The only warranties for HewlettPackard Enterprise products and services are set forth in the express warranty statements accompanyingsuch products and services. Nothing herein should be construed as constituting an additional Packard Enterprise shall not be liable for technical or editorial errors or omissions contained computer software. Valid license from Hewlett Packard Enterprise required for possession, use,or copying. Consistent with FAR and , Commercial Computer Software, Computer SoftwareDocumentation, and Technical Data for Commercial Items are licensed to the Government undervendor's standard commercial to third-party websites take you outside the Hewlett Packard Enterprise website.

2 Hewlett PackardEnterprise has no control over and is not responsible for information outside the Hewlett Packard , Itanium , Pentium , Intel Inside , and the Intel Inside logo are trademarks of Intel Corporation inthe United States and other and Windows are either registered trademarks or trademarks of Microsoft Corporation in theUnited States and/or other and Acrobat are trademarks of Adobe Systems and Oracle are registered trademarks of Oracle and/or its is a registered trademark of The Open 1 Introducing the 3810M of the (Aux) and port LEDs on front of the Mode select button and indicator and clear Port slot and module of the module tray Management (OOBM) on the back of the Stacking module 2 Installing the the Installation the Switch boots (Optional) Install the stacking the module is installed the Flex Port the or cabinet mounting the 3810M Switch in a 2-post mounting the 3810M Switch in a 4-post surface (Optional) Installing the stacking (Optional) Installing the the the Switch to a power (Optional) Installing a second power + (Optional) Connect a management the management up a console cable the network the RJ-45 cables to information and network 3 Getting Started with Switch minimal configuration through the console port to go from here.

3 Networked the IP address for remote Switch a Telnet a web browser 4 Replacing the fan the power the stacking the Flex Port 5 troubleshooting with the diagnostic the Switch by resetting the Switch console twisted-pair Switch -to-device network end-to-end network the factory default new Switch 6 module Port 3810M Switch Series Installation and Getting StartedGuideChapter 7 Cabling and technology on 1000 BASE-T cable on HPE Smart Rate Gb/s cable on HPE Smart Rate 5Gb/s cable on 10 GBASE-T cable distance conditioning patch the patch cable/connector twisted-pair cable for 10 Mbps or 100 Mbps network twisted-pair cable for 10 Mbps or 100 Mbps network twisted-pair cable for 1000 Mbps network 8 9 Support and other Hewlett Packard Enterprise self Aruba 3810M are multiport switches that can be used to build high-performance switched switches are store-and-forward devices offering low latency for high-speed networking.

4 The 3810 Mswitches also support a field-replaceable Redundant Power Supply and fan tray, Power over Ethernet(PoE/PoE+) technologies, full network management capabilities and a flexible uplink port addition, the 3810M switches support the FlexChassis Mesh feature for stacking the switches. When3810M Stacking Modules (JL084A) are installed in the switches, any combination of up to ten 3810 Mswitches can be stacked together via high-speed backplane cables to form a single extended virtual Stacking information and topologies, and the Advanced Traffic Management Guide for more switches are described in this manual:Non-PoE SwitchesPoE+ SwitchesAruba 3810M 24G 1-slot Switch (JL071A) Aruba 3810M 24G PoE+ 1-slot Switch (JL073A) Aruba 3810M 48G 1-slot Switch (JL072A) Aruba 3810M 48G PoE+ 1-slot Switch (JL074A) Aruba 3810M 16 SFP+ 2-slot Switch (JL075A) Aruba 3810M 40G 8 HPE Smart Rate PoE+ 1-slot Switch (JL076A)Accessories ListStacking ModulePower SupplyFlex port ModuleAruba 3810M 4-portStacking Module (JL084A) Aruba X371 12 VDC 250W100-240 VAC Power Supply (JL085A) Aruba 3810M 1 QSFP+ 40 GbE module(JL078A) Aruba X372 54 VDC 680W100-240 VAC Power Supply (JL086A) Aruba 3810M 2 QSFP+ 40 GbE module(JL079A) Aruba X372 54 VDC 1050W110-240 VAC Power Supply (JL087A) Aruba 3810M 4 SFP+ module (JL083A)This chapter describes these switches with the following information: Front of the switches.

5 Network Ports Management Ports LEDs ButtonsChapter 1 Introducing the 3810M switches6 Aruba 3810M Switch Series Installation and Getting StartedGuide Flex Port Slot Module Support Back of the switches: Power Supplies and Power Connectors Fan Tray Out-of-Band Management (OOBM) 3810M Stacking Module Switch FeaturesFront of the switchesFigure 1: Front of all the 3810M SwitchesChapter 1 Introducing the 3810M switches7 Table 1: Front of all the 3810M Switches Label and DescriptionLabelDescription1 Aruba 3810M 24G 1-slot Switch (JL071A)2 Aruba 3810M 48G 1-slot Switch (JL072A)3 Aruba 3810M 24G PoE+ 1-slot Switch (JL073A)4 Aruba 3810M 48G PoE+ 1-slot Switch (JL074A)5 Aruba 3810M 16 SFP+ 2-slot Switch (JL075A)6 Aruba 3810M 40G 8 HPE Smart Rate PoE+ 1-slot Switch (JL076A)Figure 2: Front of 3810M Flex Port Modules8 Aruba 3810M Switch Series Installation and Getting StartedGuideTable 2: 3810M Flex Port Modules Label and DescriptionLabelDescription1 Aruba 3810M 1 QSFP+ 40 GbE Module (JL078A)2 Aruba 3810M 2 QSFP+ 40 GbE Module (JL079A)3 Aruba 3810M 4 SFP+ Module (JL083A)4 Port LEDs5 Flex Port Module Status LEDF igure 3: Example of 3810M SwitchesTable 3: 3810M Switches Labels and DescriptionLabelDescription1 Switch Port LEDs2 LED Mode button3 Speed, PoE1, Usr LEDs4, 5 Reset, Clear buttons6 Back Module Status LED7 Aux port status LED8 USB/Auxiliary Port9RJ Serial Console10 Micro USB Console11 Global Status, Unit Identification LEDs12 Flex port Module expansion slot1310/100/1000 Base-T RJ-45 Ports1 PoE Mode LED is present only on Switch models that support 1 Introducing the 3810M switches9 Network portsTable 4.

6 Network PortsProductnumberModel name10/100/1000non-PoERJ-45 ports110/100/1000 PoE/PoE+RJ-45 ports1 SFP+ Ports2 SmartRate40 GJL071 AAruba 3810M 24G 1-slot Switch24JL072 AAruba 3810M 48G 1-slot Switch48JL073 AAruba 3810M 24 GPoE+ 1-slot Switch24JL074 AAruba 3810M 48 GPoE+ 1-slot Switch48JL075 AAruba 3810M 16 SFP+ 2-slot Switch16JL076 AAruba 3810M 40G 8 HPE Smart Rate PoE+ 1-slot Switch408JL078 AAruba 3810M 1 QSFP+ 40 GbE module1JL079 AAruba 3810M 2 QSFP+ 40 GbE module2JL083 AAruba 3810M 4 SFP+module41 All RJ-45 ports support Auto-MDIX , which means you can use either straight-through or crossover twisted-pair cables toconnect network devices to the SFP+ ports support 100Mb (100-FX and 100-BX), 1G SFP and 10G SFP+ transceiversThese products also support optional network connectivity:Table 5: Optional Network Connectivity, Speeds and TechnologiesTransceiver Form-Factor and Connector1 SpeedTechnologyCablingFlex ModuleConnectorSFP ("mini-GBIC")ConnectorSFP+ConnectorQSFP+ Connector100 Mbps100-FXFiber(multimode)LC100-BXFiber (singlemode)LC1 Gbps1000-TCopper(twisted-pair)RJ-45 Table Continued10 Aruba 3810M Switch Series Installation and Getting StartedGuideTransceiver Form-Factor and Connector1 SpeedTechnologyCablingFlex ModuleConnectorSFP ("mini-GBIC")ConnectorSFP+ConnectorQSFP+ Connector1000-SXFiber(multimode)LC1000-L XFiber(multimodeor singlemode)LC1000-LHFiber (singlemode)LC1000-BXFiber (singlemode)LC10 Gbps10-Gig DirectAttachCopper(twinaxial)NotApplicab le10-Gig SRFiber(multimode)LC10-Gig LRMF iber(multimode)LC10-Gig LRFiber (singlemode)LC10-Gig ERFiber (singlemode)40 Gbps40-Gig DirectAttach 1/3/5mCopper(twinaxial)NotApplicable40-G ig SR4 Fiber(multimode)MPO40-Gig ESR4 Fiber(multimode)MPO40-Gig LR4 Fiber (singlemode)

7 LCSmart Rate1 RateCopper(twisted pair)RJ-451 For supported transceivers, see the ArubaOS- Switch and ArubaOS-CX Transceiver technical details of cabling and technologies, see Cabling and technology portsConsole portsThere are two serial console port options on the Switch , an RJ-45 or Micro USB. These ports are used toconnect a console to the Switch either by using an RJ-45 serial cable or a standard Micro USB cable (neitherof which are supplied with the Switch ). The Micro USB connector has precedence for input, so if both cablesChapter 1 Introducing the 3810M switches11are plugged in, the console output is echoed to both the RJ and Micro-USB ports. But, the input is onlyaccepted from the more information on the console connection, see (Optional) Connect a management console. Theconsole can be a PC or workstation running a VT-100 terminal emulator, or a VT-100 (Aux) portAn auxiliary port for processing a USB command file or downloading Switch software code.

8 This port uses aUSB Type A connector, but does not comply with all USB protocols and and port LEDs on front of the switchesThis section describes the various LEDs and their 4: Switch and Port LEDs for JL071A, JL072A, JL073A, JL074A, and JL076 ATable 6: Switch and Port LEDs Label and Description for JL071A, JL072A, JL073A, JL074A, andJL076 ALabelDescription1 Switch Port LEDs2 LED Mode button3 Speed LED4 PoE LED15 Usr LED6 Reset button7 Clear button8 Back Module status LED9 Aux Port status LED10 Unit Identification LED11 Global status LED12 Aruba 3810M Switch Series Installation and Getting StartedGuide1 Only on PoE 5: Switch and Port LEDs for JL075 ATable 7: Switch and Port LEDs Label and Description for JL075 ALabelDescription1 Switch Port LEDs2 LED Mode button3 Speed LED4 Usr LED5 Reset button6 Clear button7 Back Module status LED8 Aux Port status LED9 Unit Identification LED10 Global status LEDT able 8: Front of Switch Status and Mode LED BehaviorSwitch LEDsFunctionState1 MeaningGlobal StatusInternal Power Statusof the StatusSwitch/Port FaultStatusOn GreenThe Switch has passed self-test and is powered Flash GreenThe Switch self-test andinitialization are in progressafter the Switch has beenpower cycled or reset.

9 Theswitch is not operationaluntil this LED stops ContinuedChapter 1 Introducing the 3810M switches13 Switch LEDsFunctionState1 MeaningSlow Flash OrangeA fault or self-test failurehas occurred on the Switch ,one of the Switch ports, amodule in the rear of theswitch, or the fan. TheStatus LED for thecomponent with the faultwill blink OrangeIf this LED is on orange for aprolonged time, the switchhas encountered a fatalhardware failure, or hasfailed its unit is not (Unit Identification)The Unit IdentificationLED is used to help youto identify a particularunit in a rack orcollection of or Slow FlashThe chassislocate command allows you toblink or turn on the LED fora specified number ofminutes (1-1440). Thedefault is 30 will turn off after thetimeout period has Module StatusStatus of modularcomponents installedin the back of the GreenNormal operation: Allmodular componentsinstalled in the back of theunit are Flash OrangeOne of the modulesinserted from the back ofthe chassis (power supply,fan tray, or stacking module)has failed self test or isexperiencing a faultcondition.

10 Flashessimultaneously with theGlobal Status LED Port ActivityIndicates data transferon the Aux Port whichis used for processing aUSB command file ordownloading switchsoftware GreenUSB installed andsuccessfully initialized, andmounted, but no FlickerData transfer is in not remove installeddevice until data transfer iscompleteTable Continued14 Aruba 3810M Switch Series Installation and Getting StartedGuideSwitch LEDsFunctionState1 MeaningSlow Flash OrangeThe USB device that isinstalled is unsupported USB Port Module StatusStatus of Flex GreenFlex Port module Flash OrangeFlex Port module hasexperienced a Global Status LEDshould be Flash OrangeFlex Port module or one ormore of its ports is/areexperiencing an conditions include thatan unsupported cable hasbeen installed in the moduleor that the Flex Port modulehas been installed while theswitch was powered on (hot-swapped) and the switchneeds to be rebooted tosupport the PresentNo ModuleSpeed Mode SelectedIndicates when the PortLEDs are showing portspeed Mode is LEDs indicate mode not over Ethernet (PoE)Mode Selected2 Indicates when the PortLEDs are showing PoEstatus GreenPoE Mode is selected.