Asset protection in the harshest environments - PFP …

1 KEYBENEFITS Latest generation of lightweight, high quality epoxy intumescents Certified by Lloyd s and DNV Listed Underwriter s Laboratories NORSOK M-501 tested Jet fire rated and certified Fully fire rated for offshore platform applications Easy to apply by a variety of techniques Excellent physical properties - hard, durable and flexible Virtually maintenance free - even in the harshest climatic conditions Reduced hazard from emissions in a fire environment Unrivalled global network of technical and field service support Asset protection in the harshest environments Featuring low density, low waterabsorption characteristics, and aneasier application process,Chartek 7 is the highest quality,cost efficient fire protection on themarket today.

2 Like previousgenerations of Chartek , Chartek 7 is tough, durable and virtuallymaintenance free. It is ideal forlong term fire protection onoffshore oil and gas productionplatforms, at refineries andchemical processing plants. And,what s more, it s halogen free - soin a fire, it does not generatehazardous chlorine-containing Lowest weight per unit area foroffshore applications Low cost 6mm x 6mmgalvanised mesh Flexible non-metal meshavailable to increaseproductivity for specificapplications Weld pins not required to affixmetal mesh to large broadsurfaces Higher build capacity Can be applied via single pot ordual spray systems and bytrowelHIGHLYDURABLE Meets the environmentalexposure (weatherability) requirements of UL 1709 (USA)

3 Tested to NORSOK M-501, weatherability and corrosion with excellent results Very low moisture absorption after long term submergence in salt water solution - topcoat reduces moisture absorption even further (lowest moisture absorption of any epoxy fireproofing in International Protective Coatings-sponsored tests) Lap shear strength in excess of1400 psi Compressive strength in excessof 2500 psi Flexible, not affected by deflection of substrate for pre- erection INFIREENVIRONMENT Toxicity index of in NavalEngineering Standard 713 test HCN, CO and CO2generated ina fire lower than other availablematerials Contains no halogenated flameretardant Flame spread index of andsmoke generation index in ASTM E84 testsFULLYFIRERATED FOROFFSHOREPLATFORMAPPLICATIONS Structural steel (both I andhollow section certificatesfrom Lloyd s and DNV)

4 Jet fire ratedLEADING THE WORLD IN SERVICEThe combination of technicalexpertise available to customersand clients for Chartek fireproofing prior to and afterinstallation, supported by theInternational Protective Coatingsorganisation, means that we areable to provide an unrivalledservice to our in two of ourwholly owned factories andproviding sales and logisticalsupport from 44 of our whollyowned sales office worldwide,International offer the comfortthat dealing only with the worldslargest protective coatingscompany otherwise agreed by us in writing, any contract to purchase products referred to in this brochure and any advice which we give in connection with the supply of products shall be subject to our standard conditions of contract.

5 , Chartek and International are registered trademarks. Copyright International Paint Inc., 2000 Fire & Insulation Products - Headquarters Tel: +44 1277 229192 International CoatingsFax: +44 1277 228745 Essex House 141 Kings RoadWeb Address: address: KingdomCM14 4 DRProperty Test Method Value Units Spray applied density Plural Pump1000 ( ) kg/m3(lb/ft3)Tensile strength ASTM D638 (1850) MPa (psi)Tensile modulus ASTM D638 1786 (259,000) MPa (psi)Compressive strength ASTM D695 (2700) MPa (psi)Compressive modulus ASTM D695 1172 (170,000) MPa (psi)Flexural strength ASTM D790 (3300) MPa (psi)Flexural modulus ASTM D790 1586 (230,000) MPa (psi)Lap shear strength ASTM D1002 (1450) MPa (psi)Thermal Conductivity Transient method W/m C at room temperature( )(Btu-in/hr ft2 F)Coefficient of thermal ASTM E228 68 x 10-6cm/cm Cexpansion38 x 10-6(in/in F)

6 Specific Heat at room ASTM 1269 ( ) J/g Ctemperature(Btu/lb F)Moisture Absorption Total immersion in non5% salt solution @ topcoated room temperature for 76 days topcoatedFlame SpreadASTM E84 Generation ASTM E84 Index Naval Engineering 713 Hardness Shore D Typically 70 Impact Strength / Inch ASTM D256 ( ) J/cm of notch (ft-lb/inch)ver/06/00