Example: confidence

Atmel | SMART SAM4SD32 SAM4SD16 SAM4SA16 SAM4S16 …

Atmel -11100K-ATARM-SAM4S-Datasheet_09-Ju n-15 DescriptionThe Atmel | SMART SAM4S series is a member of a family of Flashmicrocontrollers based on the high-performance 32-bit ARM Cortex -M4 RISC processor. It operates at a maximum speed of 120 MHz and features up to2048 Kbytes of Flash, with optional dual-bank implementation and cachememory, and up to 160 Kbytes of SRAM. The peripheral set includes a full-speedUSB Device port with embedded transceiver, a high-speed MCI forSDIO/SD/MMC, an External Bus Interface featuring a Static Memory Controller toconnect to SRAM, PSRAM, NOR Flash, LCD Module and NAND Flash, 2 USARTs, 2 UARTs, 2 TWIs, 3 SPIs, an I2S, as well as a PWM timer, two 3-channel general-purpose 16-bit timers (with stepper motor and quadraturedecoder logic support), an RTC, a 12-bit ADC, a 12-bit DAC and an SAM4S series is ready for capacitive touch, offering native support for theAtmel QTouch library for easy implementation of buttons, wheels and Atmel | SMART SAM4S devices have three software-selectable low-powermodes: Sleep, Wait and Backup.

Atmel QTouch® library for easy implementation of buttons, wheels and sliders. The Atmel | SMART SAM4S devices have three software-selectable low-power modes: Sleep, Wait and Backup. In Sleep mode, the processor is stopped while all other functions can be kept running. In Wait mode, all clocks and functions are

Tags:

  Wheel

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Atmel | SMART SAM4SD32 SAM4SD16 SAM4SA16 SAM4S16 …

1 Atmel -11100K-ATARM-SAM4S-Datasheet_09-Ju n-15 DescriptionThe Atmel | SMART SAM4S series is a member of a family of Flashmicrocontrollers based on the high-performance 32-bit ARM Cortex -M4 RISC processor. It operates at a maximum speed of 120 MHz and features up to2048 Kbytes of Flash, with optional dual-bank implementation and cachememory, and up to 160 Kbytes of SRAM. The peripheral set includes a full-speedUSB Device port with embedded transceiver, a high-speed MCI forSDIO/SD/MMC, an External Bus Interface featuring a Static Memory Controller toconnect to SRAM, PSRAM, NOR Flash, LCD Module and NAND Flash, 2 USARTs, 2 UARTs, 2 TWIs, 3 SPIs, an I2S, as well as a PWM timer, two 3-channel general-purpose 16-bit timers (with stepper motor and quadraturedecoder logic support), an RTC, a 12-bit ADC, a 12-bit DAC and an SAM4S series is ready for capacitive touch, offering native support for theAtmel QTouch library for easy implementation of buttons, wheels and Atmel | SMART SAM4S devices have three software-selectable low-powermodes: Sleep, Wait and Backup.

2 In Sleep mode, the processor is stopped whileall other functions can be kept running. In Wait mode, all clocks and functions arestopped but some peripherals can be configured to wake up the system based onpredefined conditions. In Backup mode, only the low-power RTC and wakeuplogic are real-time event management allows peripherals to receive, react to and sendevents in Active and Sleep modes without processor SAM4S device is a medium-range general-purpose microcontroller with thebest ratio in terms of reduced power consumption, processing power andperipheral set. This enables the SAM4S to sustain a wide range of applicationsthat includes consumer, industrial control, and PC devices operate from to SAM4S series is pin-to-pin compatible with the SAM3N, SAM3S series (48-,64- and 100-pin versions), SAM4N and SAM7S legacy series (64-pin versions).

3 SAM4S SeriesAtmel | SMART ARM-based Flash MCUDATASHEETSAM4S Series [DATASHEET] Atmel -11100K-ATARM-SAM4S-Data sheet_09-Jun-152 Features Core ARM Cortex-M4 with 2 Kbytes of cache running at up to 120 MHz Memory Protection Unit (MPU) DSP Instruction Set Thumb -2 instruction set Pin-to-pin compatible with SAM3N, SAM3S, SAM4N and SAM7S legacy products (64-pin version) Memories Up to 2048 Kbytes embedded Flash with optional dual-bank and cache memory, ECC, Security Bit and Lock Bits Up to 160 Kbytes embedded SRAM 16 Kbytes ROM with embedded boot loader routines (UART, USB) and IAP routines 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support System Embedded voltage regulator for single supply operation Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for safe operation Quartz or ceramic resonator oscillators.

4 3 to 20 MHz main power with failure detection and optional low-power kHz for RTC or device clock RTC with Gregorian and Persian calendar mode, waveform generation in low-power modes RTC counter calibration circuitry compensates for kHz crystal frequency inaccuracy High-precision 8/12 MHz factory-trimmed internal RC oscillator with 4 MHz default frequency for device startup, in-application trimming access for frequency adjustment Slow clock internal RC oscillator as permanent low-power mode device clock Two PLLs up to 240 MHz for device clock and for USB Temperature sensor Low-power tamper detection on two inputs, anti-tampering by immediate clear of general-purpose backup registers (GPBR) Up to 22 Peripheral DMA (PDC) channels Low-power Modes Sleep, Wait and Backup modes.

5 Consumption down to 1 A in Backup mode Peripherals USB Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional Endpoints, on-chip transceiver Up to two USARTs with ISO7816, IrDA , RS-485, SPI, Manchester and Modem Mode Two 2-wire UARTs Up to two 2-Wire Interface modules (I2C-compatible), one SPI, one Serial Synchronous Controller (I2S), one high-speed Multimedia Card Interface (SDIO/SD Card/MMC) Two 3-channel 16-bit Timer Counters with capture, waveform, compare and PWM mode, Quadrature decoder logic and 2-bit Gray up/down counter for stepper motor 4-channel 16-bit PWM with complementary output, fault input, 12-bit dead time generator counter for motor control 32-bit Real-time Timer and RTC with calendar, alarm and 32 kHz trimming features 256-bit General Purpose Backup Registers (GPBR) Up to 16-channel, 1 Msps ADC with differential input mode and programmable gain stage and auto calibration One 2-channel 12-bit 1 Msps DAC One Analog Comparator with flexible input selection, selectable input hysteresis 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)

6 For data integrity check of off-/on-chip memories Register Write Protection3 SAM4S Series [DATASHEET] Atmel -11100K-ATARM-SAM4S-Data sheet_09-Jun-15 I/O Up to 79 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die series resistor termination Three 32-bit Parallel Input/Output Controllers, Peripheral DMA-assisted Parallel Capture mode Packages 100-lead packages LQFP 14 x 14 mm, pitch mm TFBGA 9 x 9 mm, pitch mm VFBGA 7 x 7 mm, pitch mm 64-lead packages LQFP 10 x 10 mm, pitch mm QFN 9 x 9 mm, pitch mm WLCSP x mm, pitch mm ( SAM4SD32 / SAM4SD16 ) WLCSP x mm, pitch mm ( SAM4S16 /S8) WLCSP x mm, pitch mm (SAM4S4/S2) 48-lead packages LQFP 7 x 7 mm, pitch mm QFN 7 x 7 mm, pitch mmSAM4S Series [DATASHEET] Atmel -11100K-ATARM-SAM4S-Data sheet_09-Jun-154 Safety Features Highlight Flash Built-in ECC (hamming), single error correction Security bit and lock bits5 SAM4S Series [DATASHEET] SummaryThe SAM4S series devices differ in memory size, package and features.

7 Table 1-1 and Table 1-2 summarize theconfigurations of the device :1. One channel is reserved for internal temperature Three TC channels are reserved for internal Full modem support on Summary for SAM4SD32 /SD16/SA16/S16 DevicesFeatureSAM4SD32 CSAM4SD32 BSAM4SD16 CSAM4SD16 BSAM4SA16C SAM4SA16 BSAM4S16 CSAM4S16 BFlash2 x 1024 Kbytes 2 x 1024 Kbytes 2 x 512 Kbytes 2 x 512 Kbytes1024 Kbytes1024 Kbytes1024 Kbytes1024 KbytesSRAM160 Kbytes160 Kbytes160 Kbytes160 Kbytes160 Kbytes160 Kbytes128 Kbytes128 KbytesHCACHE2 Kbytes2 Kbytes2 Kbytes2 Kbytes2 Kbytes2 Kbytes PackageLQFP100 TFBGA100 VFBGA100 LQFP64 QFN64 WLCSP64 LQFP100 TFBGA100 VFBGA100 LQFP64 QFN64 WLCSP64 LQFP100 TFBGA100 VFBGA100 LQFP64 QFN64 LQFP100 TFBGA100 VFBGA100 LQFP64 QFN64 WLCSP64 Number of

8 PIOs7947794779477947 ExternalBusInterface8-bit data,4 chip selects,24-bit address 8-bit data, 4 chip selects,24-bit address 8-bit data, 4 chip selects,24-bit address 8-bit data,4 chip selects,24-bit address 12-bit ADC16 ch.(1)11 ch.(1)16 ch.(1)11 ch.(1)16 ch.(1)11 ch.(1)16 ch.(1)11 ch.(1)12-bit DAC2 CounterChannels66(2)66(2)66(2)66(2)PDC Channels2222222222222222 USART/UART2/2(3)2/2(3)2/2(3)2/2(3)2/2(3) 2/2(3)2/2(3)2/2(3)HSMCI1 port, 4 bits1 port, 4 bits1 port, 4 bits1 port, 4 bits1 port, 4 bits1 port, 4 bits1 port, 4 bits1 port, 4 bitsTable Summary for SAM4S8/S4/S2 DevicesFeatureSAM4S8 CSAM4S8 BSAM4S4 CSAM4S4 BSAM4S4 ASAM4S2 CSAM4S2 BSAM4S2 AFlash512 Kbytes512 Kbytes256 Kbytes256 Kbytes256 Kbytes128 Kbytes128 Kbytes128 KbytesSRAM128 Kbytes128 Kbytes64 Kbytes64 Kbytes64 Kbytes64 Kbytes64 Kbytes64 KbytesHCACHE PackageLQFP100 TFBGA100 VFBGA100 LQFP64 QFN64 WLCSP64 LQFP100 TFBGA100 VFBGA100 LQFP64 QFN64 WLCSP64 LQFP48 QFN48 LQFP100 TFBGA100 VFBGA100 LQFP64 QFN64 WLCSP64 LQFP48 QFN48 Number of PIOs7947794734794734 ExternalBusInterface8-bit data,4 chip selects,24-bit address 8-bit data,4 chip selects.

9 24-bit address 8-bit data,4 chip selects,24-bit address 12-bit ADC16 ch.(1)11 ch.(1)16 ch.(1)11 ch.(1)8 ch.(1)16 ch.(1)8 ch12-bit DAC2 ch. 2 ch. Timer CounterChannels66(2)66(2)6(2)66(2)6(2)PD C Channels2222222222222222 USART/UART2/2(3)2/2(3)2/2(3)2/2(3)2/12/2 (3)2/2(3)2/1 HSMCI1 port, 4 bits1 port, 4 bits1 port, 4 bits1 port, 4 bits 1 port, 4 bits1 port, 4 bits SAM4S Series [DATASHEET] DiagramFigure 100-pin Version Block DiagramSPIPDCID AHB/APBB ridgePCK[2:0]XINXOUTXIN32 XOUT32 ERASEVDDIOVDDCOREADTRGS ystem ControllerTCK/SWCLKTDITDOJTAGSELVDDIOVDD OUTJTAG and Serial WireFlashUniqueIdentifierVoltageRegulato rAnalog ComparatorCRCCUNPCS[3:0]MISOMOSISPCKTSTA DCVDDPLLTCLK[2:0]TIOA[2:0]TIOB[2:0]TCLK[ 5:3]TIOA[5:3]TIOB[5:3]DACPDCPWMH[3:0]PWM L[3:0]PWMFI0 ADVREFDAC[1:0]DATRGHigh-speedMCITKTDRDRK RFSSCPDCUSB [7:0]A[23:0]A21/NANDALEA22/NANDCLENWAITN CS[3.]

10 0]NRDNWENANDOENANDWEIn-Circuit EmulatorMPUC ortex-M4 ProcessorfMAX 120 MHzNVIC24-bit SysTickCounterDSPT ransceiverMCCKMCCDAMCDA[3:0]Flash2*1024/ 2*512/1024 KbytesDDPDDMDACTemp. SensorADVREFADCPDCUserSignatureWKUP[15:0 ]RTCOUT0 RTCOUT1 NRSTAD[14:0]PIOA/PIOB/PIOCTMS/SWDIOPDCT imer Counter 0TC[ ]Timer Counter 1TC[ ]Temp SensorPWMSRAM160 Kbytes ROM16 Kbytes Event SystemSSupplyController32K CrystOsc256-bit GPBRReal-timeTimerReal-timeClockWatchdog TimerPLLAP owerManagementController3 20 MHzOscillatorRC Osc4/8/12 MHzUART0 URXD0 UTXD0 PDCUART1 URXD1 UTXD1 PDCPLLBTWCK1 TWD1 TWI1 PDCTWCK0 TWD0 TWI0 PDCPDCCMCC(2 Kbyte Cache)PDCE xternal BusInterfaceNAND FlashLogicStatic MemoryControllerRXD0 TXD0 SCK0 RTS0 CTS0 USART0 PDCUSART1 PDCRXD1 TXD1 SCK1 RTS1 CTS1RI1 DCD1 DSR1 DTR1 PIOPDCPIODC[7:0]PIODCCLKPIODCEN[2.


Related search queries