Axial-Flow Compressors

1 Introduction The Compressors in most gas turbine applications, especially units over 5MW, use axial fl ow Compressors . An axial fl ow compressor is one in which the fl ow enters the compressor in an axial direction (parallel with the axis of rotation), and exits from the gas turbine, also in an axial direction. The axial-fl ow compressor compresses its working fl uid by fi rst accelerating the fl uid and then diffusing it to obtain a pressure increase. The fl uid is accelerated by a row of rotating airfoils (blades) called the rotor, and then diffused in a row of stationary blades (the stator).

2 The diffusion in the stator converts the velocity increase gained in the rotor to a pressure increase. A compressor consists of several stages: 1) A combination of a rotor followed by a stator make-up a stage in a compressor; 2) An additional row of stationary blades are frequently used at the compressor inlet and are known as Inlet Guide Vanes (IGV) to ensue that air enters the fi rst-stage rotors at the desired fl ow angle, these vanes are also pitch variable thus can be adjusted to the varying fl ow requirements of the engine; and 3) In addition to the stators, another diffuser at the exit of the compressor consisting of another set of vanes further diffuses the fl uid and controls its velocity entering the combustors and is often known as the Exit Guide Vanes (EGV).

3 In an axial fl ow compressor, air passes from one stage to the next, each stage raising the pressure slightly. By producing low-pressure increases on the order of :1 to :1, very high effi ciencies can be obtained as seen in table 1. The use of multiple stages permits overall pressure increases of up to 40:1 in some aerospace applications and a pressure ratio of 30:1 in some Industrial applications. The last twenty years has seen a large growth in gas turbine technology. The growth is spear headed by the increase in compressor pressure ratio, advanced combustion techniques, the growth of materials technology, new coatings and new cooling schemes.

4 The increase in gas turbine effi ciency is dependent on two basic parameters: 1. Increase in Pressure Ratio 2. Increase in Firing Temperature It also should be remembered that the Gas Turbine Axial Flow Compressor consumes between 55%-65% of the power produced by the Turbine section of the gas 1 Axial Flow Compressor Characteristics Type of ApplicationType of FlowInlet Relative Velocity Mach NumberPressure Ratio per StageEffi ciency per The aerospace engines have been the leaders in most of the technology in the gas turbine. The design criteria for these engines was high reliability, high performance, with many starts and fl exible operation throughout the fl ight envelope.

5 The engine life of about 3500 hours between major overhauls was considered good. The aerospace engine performance has always been rated primarily on its Thrust/Weight ratio. Increase in engine Thrust / Weight Ratio is achieved by the development of high aspect ratio blades in the compressor as well as optimizing the pressure ratio and fi ring temperature of the turbine for maximum work output per unit fl Industrial Gas Turbine has always emphasized long life and this conservative approach has resulted in the Industrial Gas Turbine in many CompressorsMeherwan P.

6 Boyce2121 Kirby Drive, Number 28 NHouston, TX 77019713-807--0888713-807-0088 giving up high performance for rugged operation. The Industrial Gas Turbine has been conservative in the pressure ratio and the firing temperatures. This has all changed in the last ten years; spurred on by the introduction of the Aero-Derivative Gas Turbine the Industrial Gas Turbine has dramatically improved its performance in all operational aspects. This has resulted in dramatically reducing the performance gap between these two types of gas turbines. Figure 1 indicates the growth of the Pressure Ratio in a gas turbine over the past 50 years.

7 The growth of both the Pressure Ratio and Firing Temperature parallel each other, as both growths are necessary to achieving the increase in thermal efficiency in Gas Turbines. The Axial flow compressor in most of the advanced gas turbine is a multistage compressor consisting of 17-22 stages with an exceedingly high pressure ratio. It is not uncommon to have pressure ratios in industrial gas turbines in the 17 to 20:1 range with some units having pressure ratios in the 30:1 range. Figure 2 shows a multistage high-pressure axial flow compressor rotor. The low-pressure increase per stage also simplifies calculations in the preliminary design of the compressor by justifying the air as incompressible in its flow through the stage.

8 Engine Pressure Ratio Development05101520253035404519401950196 019701980199020002010 Year Pressure ratioPressure Ratio AircraftPressure Ratio of pressure ratio over the past 50 yearsFig. 2. Axial Flow Compressor Rotor165 Figure 3 shows the stators, the stationary blades which are in between each rotor blade and causes the flow to be diffused (increase in the static pressure, reduction of the absolute velocity). The early stages of the stators in figure 3 are adjustable, as can be noted by their circular base. The adjustable stators allow the stator to be positioned to the correct flow angle leaving the blades as the air mass flow varies with load and inlet 3.

9 Axial Flow Compressor Stators located in the casing As with other types of rotating machinery, an axial compressor can be described in a cylindrical coordinate system. The z axis is along the axis of rotation which is along the running length of the compressor shaft, the radius r is measured outward from the shaft, and the angle of rotation is the angle turned by the blades in figure 4. This coordinate system will be used throughout this discussion of Axial-Flow Compressors . Fig. 4. Coordinate System for Axial-Flow Compressor Figure 5 shows the pressure, velocity, and total temperature variation for flow through several stages of an axial compressor.

10 As indicated earlier in figure 3, the length of the blades, and the annulus area, this is the area between the shaft and shroud, decreases throughout the length of the compressor. This reduction in flow area compensates for the increase in fluid density as it is compressed, permitting a constant axial velocity. In most preliminary calculations used in the design of a compressor, the average blade height is used as the blade height for the P. BoyceFig. 5 Variation of Temperature Velocity, and Pressure through an Axial-Flow Blade and Cascade Nomenclature Since airfoils are employed in accelerating and diffusing the air in a compressor, much of the theory and research concerning the flow in axial Compressors are based on studies of isolated airfoils.