Transcription of BEGINNER PROGRAMMING LESSON
1 By Sanjay and Arvind SeshanEV3 Classroom: introduction to the EV3 Brick and EV3 Classroom SoftwareBEGINNER PROGRAMMING LESSONLESSON how the EV3 brick about the main components of the EV3 Classroom to the EV3 brickNote: This LESSON uses the new Scratch-based Education software (EV3 Classroom). However, it is the same for the Retail 2020 (Last edit: 12/21/2019) THE BRICK BUTTONS1 = BackUndoStop ProgramTurn robot off2 = Center ButtonSelect optionsRun Program/ProjectTurn robot on3 = L, R, Up, DownNavigate menusCopyright 2020 (Last edit: 12/21/2019) 123333 THE BRICK SCREENTabs on RecentFind programs/projects you ran recently2.
2 File NavigationFind all programs by project3. Brick AppsPort views4. SettingsBluetooth, Wifi, VolumeCopyright 2020 (Last edit: 12/21/2019) 1234 PORTS, SENSORS, MOTORSC opyright 2020 (Last edit: 12/21/2019) Ports 1, 2, 3, 4 = SensorsPorts A, B, C, D = MotorsDefault setup assumes Right Motor in C, Left Motor in BBCD efault setupFrontEV3 CLASSROOM: GETTINGSTARTEDC opyright 2020 (Last edit: 12/21/2019) Follow the onscreen steps and then click START to access the PROGRAMMING environmentEV3 CLASSROOM: HOMEC opyright 2020 (Last edit: 12/21/2019) Start New ProjectOpen Saved ProjectMY PROJECTSC opyright 2020 (Last edit.)
3 12/21/2019) [1][2]My Projects shows a list of the projects you have edit an existing project click on the edit icon [1] and then select the project you want to modify. Select the desired action (delete/duplicate/rename) [2].NEW PROJECTO pened ProjectsProject Properties Rename Project or Move File to new location ( Save as)Copyright 2020 (Last edit: 12/21/2019) Back to HomeNew ProjectToggle between showing all/fewer code blocks We highly recommend you click this so that it will show all the blocks our lessons require ABOUT PROJECTS FOR EV3-G USERS For those familiar with the labview based EV3-G software, there is no differentiation between projects and programs in this software.
4 Each project is a separate program My Blocks cannot be used between ProjectsCopyright 2020 (Last edit: 12/21/2019) PROGRAMMING CANVASB lock PaletteProgramming AreaDownload/RunCopyright 2020 (Last edit: 12/21/2019) Brick DashboardTo add a comment or delete a block, right click on the PROGRAMMING MENUC opyright 2020 (Last edit: 12/21/2019) the Settings icon in the Home to Help on the left hand columnBLOCK PALETTEC opyright 2020 (Last edit: 12/21/2019) Motors Control an individual motorMovement Control 2 motors at a time with synchronizationDisplay Write to screenSound Play a soundEvents Run actions based on events ( sensor or timer)Control Loops, if/else statements, Read a sensor valueOperators Mathematics and logicVariables Store data in a variable or listMy Blocks Custom defined blocksNote: To see certain blocks, you may have to click on ALL CODEBLOCKS CONNECTING TO BRICKC opyright 2020 (Last edit.)
5 12/21/2019) The software will auto-connect to the brick if you are using USBTo connect over Bluetooth, click the connect button. Enable Bluetooth as shown, andclick connect. In the connect dialogue, select your EV3 brick s name. You might have to change to EV3 passcode to 0000 when asked if the connection is unsupported in this version of the softwareCREDITSA uthor: Sanjay and Arvind SeshanMore lessons are available at 2020 (Last edit: 12/21/2019) This work is licensed under aCreative Commons International License.