Example: biology

Belt Number & Identification Chart - Kaman

belt Number & Identification ChartBelt Number & Identification ChartFor Comprehensive ProductInformation, See Gates IndustrialPower Transmission SystemsCatalog BeltsAll synchronous belts are identified in a similar manner, in either English or metric units. Belts are measured by:1. Pitch: Distance in inches or millimeters between two adjacent tooth centers as measured on the belt pitch Pitch Length: Total length (circumference) in inches or millimeters as measured along the pitch line. It is equalto the pitch multiplied by the Number of teeth in the Width: Always shown as the last part of the size designation. Denotes width in inches or widths include: 4mm, 6mm, 9mm; 3mm widths include:6mm, 9mm, 15mm; 5mm widths include: 9mm, 15mm, 25mm;8mm widths include: 20mm, 30mm, 50mm, 85mm;14mm widths include: 40mm, 55mm, 85mm, 115mm, 170mm;Examples:640-8 MGT-20 BeltP22-8 MGT-20 1108 SprocketExamples:5MR-300-09 BeltP18-5 MGT-15 (mm) (in.)

Aug 31, 2010 · Examples: TP800H100 Belt (Timing) TP1200-8M-20GT Belt (GT) TP1200-8MGT-20 Belt (GT2) WARNING: Do not use Gates belts, pulleys or sprockets on any aircraft propeller or rotor drive systems or in-flight accessory drives. Gates products are not designed or intended for aircraft use. Stock Belt Pitch Reference Dimensions

Tags:

  Belt, Timing, Pulleys

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Belt Number & Identification Chart - Kaman

1 belt Number & Identification ChartBelt Number & Identification ChartFor Comprehensive ProductInformation, See Gates IndustrialPower Transmission SystemsCatalog BeltsAll synchronous belts are identified in a similar manner, in either English or metric units. Belts are measured by:1. Pitch: Distance in inches or millimeters between two adjacent tooth centers as measured on the belt pitch Pitch Length: Total length (circumference) in inches or millimeters as measured along the pitch line. It is equalto the pitch multiplied by the Number of teeth in the Width: Always shown as the last part of the size designation. Denotes width in inches or widths include: 4mm, 6mm, 9mm; 3mm widths include:6mm, 9mm, 15mm; 5mm widths include: 9mm, 15mm, 25mm;8mm widths include: 20mm, 30mm, 50mm, 85mm;14mm widths include: 40mm, 55mm, 85mm, 115mm, 170mm;Examples:640-8 MGT-20 BeltP22-8 MGT-20 1108 SprocketExamples:5MR-300-09 BeltP18-5 MGT-15 (mm) (in.)

2 AB " ".0787 " ".1181 " ".197 " ".315 " ".552 Pitch5mm Pitch8mm Pitch14mm Pitch2mm PitchExamples: 210L100 belt (in.) " ".080 in..045 " ".200 in..090 " ".375 in..140 " ".500 in..160 " ".875 in..440 " " in..620 : TP800H100 belt ( timing ) TP1200-8M-20GT belt (GT) TP1200-8 MGT-20 belt (GT2)WARNING: Do not use Gates belts, pulleys or sprockets on any aircraft propeller or rotor drive systems or in-flight accessory products are not designed or intended for aircraft belt Pitch Reference DimensionsAvailable in 2mm, 3mm, 5mm, 8mm, 14mmand 20mm : PowerGrip GT2 belts must be used with PowerGrip GT2 sprockets for new designsNote: 8 and 14 mm pitch PowerGrip GT2 belts can be used as replacement belts at the nextsmaller width for the following: HTD, Rpp, Rpp+Plus, HTB, HPT, HT100, HT150, ETH, HPR, HPPD, EHT or : 14mm-170mm width substitute a PowerGrip GT2-14mm-115 without any performance.

3 8 MGT-640-12 belt 8MX-22S-12 1008 GT2 Sprocket8mm widths include: 12mm, 21mm, 36mm, 62mm;14mm widths include: 20mm, 37mm, 68mm, 90mm, 125mm20mmPitchBCAA vailable in 8mm and 14mm (mm) (in.)AB belt Pitch Reference DimensionsNOTE: Gates recommends that Poly Chain GT2 belts run only in Poly Chain GT2 sprockets when used for new recommends that Poly Chain GT2 belts be used for replacement belts in Poly Chain GT widths include: 6mm, 9mm, 15mm5mm widths include: 9mm, 15mm, 25mm20mm widths include: 115mm, 170mm, 230mm, 290mm, 340mmExamples: 350-5M-15 belt P28-5M-15AL SprocketAvailable in 3mm and 5mm (mm) (in.)AB " " .1181 " ".197 " ".787 belt Pitch Reference Dimensions5mmPitchBCAABCXXHXHHLXLMXLS tock belt Pitch Reference DimensionsAvailable in the following widths:MXL widths include:012 (.)

4 125")019 (.188")025 (.250")XL widths include:025 (.250")037 (.375")L widths include:050 (.500")075 (.750")100 ( ")H widths include:XH widths include:200 ( ")300 ( ")400 ( ")XXH widths include:075 (.750")100 ( ")150 ( ")200 ( ")300 ( ")200 ( ")300 ( ")400 ( ")500 ( ") (in.) " ".200 " ".375 " ".500 BeltsStock belt Pitch Reference DimensionsStock belt Pitch Reference DimensionsPowerGrip GT2 Stock belt Pitch Reference (mm) (in.) " ".118 " " .197 " " .315 " " .552 widths include: 025 (.250"), 037 (.375")L widths include: 050 (.500"), 075 (.750"), 100 ( ")H widths include: 075 (.750"), 100 ( "),150 ( "), 200 ( "), 300 ( ")A8mm Pitch3, 5, 8 & 14mm PowerGrip GT2 available inthe standard single sided belt widthsNote: Additionalsizes availableTruflex BeltNumber SystemPart numbers are derived from IndustryStandard Number .

5 First digit in Gatesnumber corresponds to first two digitsof Industry Standard Example: 4L450. 2450 = 4L450 belt length is to the nearest tenth of an belt is " cross section designation with Outside Circumference ( ) to the nearest whole Number , plus a zero to determineBelt Part Number . Example: 5/8" top width 5VX belt with 80" equals 5VX800 V- belt . X designates molded notch cross section plus Inside Circumference ( ) to determine belt part Number . To calculate , subtract thefollowing values from the ( ):Cross SectionABCDES ubtract From "3" (Above 210", ")4" (Above 210", ")5" (Above 210", ")7"(Above 210", ")Dubl-V belts are available in AA, BB, CC and DD cross sectionsTri-Power construction is identified by its distinctivemolded notch configuration.

6 To determine partnumber, follow method for Hi Power II mm8 mmSPZ13 mmSPA10 mm16 mm13 mmSPB22 mmSPC18 mm10 mm6 mm10mm13 mm13mm8 mm17 mm10 mm17mmNarrow and classical sizes in molded notch construction. Lengths over 3,000mm are banded BeltsFirst two digits indicate top width in sixteenths of an two digits designate sheave angle in degrees that the belt is designed to fit. Last three or four digits indicatepitch length to the nearest tenth of an : belt No. 2326V310 designates:2326V310 Top Width in 16ths ofSheave Angle in Multi-SpeedPitch Circumfrence to thean Inch: 23/16" = 1-7/16"Degrees (26)Nearest 10th Inch: "Explanation ofNumbering System1/2"21/32"5/16"3/8"4L68_5L69_3/8"7 /32"3L67_PoweRated BeltNumbering SystemFirst two digits are belt top width in = 3/8", 68 = 1/2", 69 = 21/32"Last two digits indicate length in : PoweRated V- belt 6823 has a 1/2" top width and a 23" : First two digits plus "3/8"5/8"5/8"1"5/16"5/16"17/32"17/32"7/8 "1/2"5/16"AX21/32"13/32"BX7/8"17/32"CXMa de by joining two or more single V-belts with a permanent, high strength tie-band.

7 PowerBand belts preventturn-over or jumping off the sheave problems associated with heavy shock-loads on individual belts. PowerBandbelts use the same system of size and length designation as individual same 3V, 3VX, 5V, 5VX & 8V sections are available as in single Super HC & Super HC Molded Notch & 5VX PB available in Vextra same A, B, C & D sections are available as in single Hi-Power II section PowerBand belts may be made to tensile cords provide superior service on highimpact, shock-loaded drives. Available in selected sizes ofSuper HC and Hi-Power II by a three-part symbol consisting of:(1) A standard length designation, (2) cross section(3) Number of : The belt designation 780L12 represents:(1) An effective length of 78".

8 (2) L cross section.(3) 12 ribs Section3/8"L Section3/16"J Section3/32"1/4"1/8"2L (0)3/8"7/32"3L (1)1/2"5/16"4L (2)21/32"3/8"5L (3)*Available standard in 2 or 3 "21/32"7/8"1-1/4"1-1/2"5/16"13/32"17/32" 3/4"29/32"AB CDELong Length BeltingLong Length BeltingSynchro-Power Polyurethane BeltingEndless belts are available in metric ( ), T5 (5mm), T10 (10mm); AT5 (5mm) and AT10 (10mm) in conventional pitches: MXL (.080") and XL (.375")Also available are the double sided toothed belts T5DL (5mm) and T10DL (10mm) : Refer to Catalog No. 19993 for , 3mm, 5mm & 8mm PowerGrip GT2(Fiberglass) 5mm & 8mm PowerGrip GT2 (Steel)3mm, 5mm, 8mm & 14mm PowerGrip HTD (Fiberglass) 14mm PowerGrip HTD (Steel)MXL, XL, L and H pitch PowerGrip timing (Fiberglass) XL, L and H pitch PowerGrip timing (Steel)Available in 8mm and 14mm Poly Chain GT 2 Note: Minimum order quantity 50 ft.

9 Fiberglass construction, 98 ft. steel construction. 50 ft. in Poly Chain GT2 construction. Note: Refer to Catalog No. 19993 for in T5, T10, T20, AT5, AT10, AT20, WT10, 5 HTD, 8 HTD, 14 HTD, XL, L, H, XH and WH : Minimum order quantities apply. Note: Refer to Catalog No. 19993 for widths, constructions and stocked " " (3/8") pitch (L)5/32"1/4"1/2"9/32"5M**7M**11M*3M*1/8" 3/32"7/32"11M7/16"7M9/32"5M3/16"1/8"3M3/ 32"1/8"7/32"9/32"**Available standard in 2, 3, 4, and5 of America12998-J (1/05)


Related search queries