Blohm+Voss Pipe Handling Equipment

1 Blohm + Voss pipe Handling Equipment MPCH Master Bushing for Rotary Table . PN 553 300 (Oilwell/Wirth type). PN 553 440 (EMSCO type). PN 553 350 (National type). Technical Documentation Original Instructions Manual PN 553300-D Rev. 004,February 2012. Blohm + Voss Oil Tools 1. GENERAL INFORMATION. Warnings and Note Intended use of this Intellectual property CE Marking WARNING: A warning manual All rights retained. No part The tool complies with the indicates a definite risk of This manual is intended of this document may be Machinery Directive Equipment damage or danger for use by field service, reproduced in any form 98/37/EC and 2006/42/EC. to personnel. Failure to engineering, installation, (print, photocopy, microfilm observe and follow proper operation, and repair or any other procedure) For machines containing procedures could result personnel.

2 Every effort has or be processed using an any hydraulic or pneumatic in serious or fatal injury been made to ensure the electronic system without powered parts, the Directive to personnel, significant accuracy of the information written approval of Blohm + 94/9/EC Equipment property loss, or significant contained herein. Blohm Voss Oil Tools. and protective systems Equipment damage. + Voss Oil Tools, will not All information contained in potentially explosive be held liable for errors in this manual is based atmospheres applies. NOTE: A note indicates in this material, or for upon the latest product The marking is as follows: that additional information is consequences arising from information available at any CE Ex II 2G T5 (hydraulic provided about the current misuse of this material.)

3 Time of printing. tools) or CE Ex II 2G T6. topics. Anyone using service Dependent on ongoing (pneumatic tools). procedures or tools, whether technical improvements WARNING: This technical or not recommended by (ISO 9001) Blohm + Voss documentation contains Blohm + Voss Oil Tools, must Oil Tools reserves the instructions on safety, be thoroughly satisfied that right to change the design installation, operation and and specifications without Limited Warranty neither personal safety nor maintenance for the Blohm + Equipment safety will be announcement. The warranty provided will Voss Oil Tools tool . It must jeopardized. The values specified in be void if the tool is either: be studied before working this manual represent the 1. Repaired or serviced by with the tool.

4 Nominal values of a unit a service facility which produced in series. Slight was not authorised by Improper / Unsafe Use deviations in the case of Blohm + Voss Oil Tools. the individual devices are 2. Replacement parts not The tool must only be used possible. manufactured by Blohm for the designated purpose. + Voss Oil Tools are When using the tool, the NOTE: In the event of used. rated load must never be problems that cannot be 3. Modifications were made exceeded. solved with the aid of this to the tool which were manual, please contact not approved by Blohm one of the addresses listed + Voss Oil Tools. below. Manufacturer & Agents World wide Blohm + Voss Oil Tools Blohm + Voss Oil Tools, LLC Premier Sea & Land Pte. Ltd. Hermann-Blohm-Stra e 2 7670 Woodway, Suite 266 1, Scotts Road 20457 Hamburg Houston, #19-12 Shaw Centre Germany Texas 77063 Singapore 228208.

5 United States of America Republic of Singapore Phone: +49 40/3119-1826/1162 Phone: +1-713-952 0266 Phone: +65-6734-7177. Fax: +49 40/3119-8194 Fax: +1-713-952 2807 Fax: +65-6734-9115. 2. General safety issues Safe Handling WARNING Handles/grip WARNING: One should avoid points are marked by green TABLE OF CONTENTS. creating ignition sources, WARNING: It is not allowed paint. During operations like heat, as a result of the to use any components which these grips are the only use of the tool with other Warning sign PN 671638. are of "non-B+V" origine, or places the tool can be tools or Equipment . General warning use "non-OEM" parts which handled safely. In all NON- are not approved by B+V. green marked places there is WARNING: Do not use the It will void any warranty a risk for injury.

6 Automatic/. tool for any other purpose and may effect the correct remote operated tools may than given in this document functioning of the tool and not have any green painted within it`s specification. it's safety features. grip- points. In this case it DESCRIPTION. is not allowed to touch the WARNING: Failure to WARNING: The company tool while operating. conduct routine maintenance operating the tool is Warning sign PN 671642. Pay attention: Apply grease at least could result in Equipment responsible for evaluating once a day. damage or injury to safe and proper use of the personnel. tool in a hazard analysis. WARNING: Wear personal WARNING: The operating INSTALLATION. protection Equipment while company is obligated to working with the Equipment . issue working instructions for safe use and supervise Safe gripping points WARNING: If any safety observance of these working elements (like safety ropes, instructions.)

7 Safety sheets, plates or washers) were disassembled WARNING: Every Employee, due to maintenance work, which operates, services, Warning sign PN 611524. OPERATIONS. do NOT re- use them. Always inspects or otherwise Danger: Do not touch. replace them with new safety involved with the use of the elements. tool in other areas has to ensure, that these actions WARNING: All warning are done by trained and by plates, signs and labels an Blohm + Voss Oil Tools attached to the Equipment authorized personnel, must be observed. The and should complete regular MAINTENANCE. & INSPECTION. warning plates, signs and courses of training, to labels must be present on ensure proper use as well the tool. Do not remove the as safe operation, correct Warning sign PN 671640-1.

8 Labels. If they are missing, maintainance and inspection. Pay attention: Do not place your replacing is mandatory. hands between moving parts. WARNING: If necessary, WARNING: Any modification a reasonable, additional to the tool carried out supervisor should be without the approval of appointed during operation. DARWINGS. Blohm + Voss Oil Tools will void any warranty. WARNING: Stay away from the tool during operation. In WARNING: Using the tool case it is remote operated it with damaged or worn parts may make movements without can create serious incidents. warning. Warning sign PN 671641. Pay attention: Risk of crushing. 3. DECLARATION OF INCORPORATION We, Blohm + Voss Oil Tools TABLE OF CONTENTS. Hermann-Blohm-Strasse 2 20457 Hamburg Phone:+49(0)40 3119-1139.

9 Fax:+49(0)40 3119-3305. declare that the product Master Bushing with Insert Bowl Type B+V MPCH. DESCRIPTION. as serial-no.: 79693. which is the subject of this declaration, is in accordance with the directive of the European Parliament and Machinery Directive 2006/42/EC; Annex II B for Incomplete Machines). will be marketed in the state delivered according to the order confirmation and with the contractually agreed scope of delivery in compliance with the following guidelines, harmonized standards and if applicable special, locally required regulations. INSTALLATION. Functional Description: The master bushing is constructed on a drilling rig in order to receive the Standard Rotary Slips according to API specification 7K and, if applicable, the Bit Breaker Adapter with pin drive dimensions according to API.

10 Specification 7K and is installed in rotary tables according to API specification 7K. The following underlying health and safety protection requirements according to Annex I of Directive 2006/42/EC on machines were applied and complied with: OPERATIONS. -General Policies No. 1. -Nos. - ; Nos. ; Nos. ; Nos. ; Nos. ; Nos. ; Nos. ; Nos. ; Nos. ; Nos. ;. The special technical documents as per Annex VII B were created by the RO division of Blohm + Voss Oil Tools, Hermann- Blohm-Stra e 2, 20457 Hamburg, Germany. Note: MAINTENANCE. & INSPECTION. The aforementioned Master Bushing is an incomplete machine in terms of Directive 2006/42/EC, Art. 2 g) and is provided and designed for installation in a machine (Annex). The Master Bushing may only be put into operation if the user/operator/technician, who installs this Master Bushing into another incomplete machine or into a complete machine, declares that the complete machine meets the provisions of this directive and, if applicable, further applicable EC directives.