Boiler room Guide - cleaverbrooks.com

1 Boiler Room Guide FOREWORD. This Guide is provided to assist supervisory, operating and maintenance personnel in understanding the operation of Boiler room equipment, and to provide guidance to achieve safe and efficient operation of the equipment. Automatic features provided in the design of Boiler room equipment relieves the operator from mundane and repetitive tasks, but routine maintenance of all of the equipment is never to be neglected by the operators or maintenance personnel. The information provided in this Guide is for general guidance in proper equipment operation and maintenance.

2 The operation maintenance and parts manual for a specific piece of equipment should be reviewed for details and safety requirements. No attempt should be made to operate equipment until the principles of operation and all of the components are thoroughly understood. Failure to follow all applicable instructions and warnings may result in personal injury or damage to the equipment. Because of the multiplicity of national, state, local, or other applicable codes pertaining to the design, manufacture, installation and operation of steam and hot water boilers, no attempt will be made in this Guide to set any mandatory rules.

3 The operation of this equipment by the owner and his/her operating personnel must comply with all requirements or regulations of his/. her insurance company and/or any other authority having jurisdiction. These requirements take precedence over anything contained herein. TABLE OF CONTENTS. Chapter 1. General Boiler Description The Firetube Boiler .. 1-1. THE WATERTUBE Boiler .. 1-2. Packaged Boilers .. 1-2. FIELD ERECTABLE BOILERS .. 1-3. THREE PASS FIRETUBE BOILERS .. 1-4. OTHER Boiler DESIGNS .. 1-4.

4 REGULATORY CODES .. 1-5. GENERAL ACCESSORY EQUIPMENT .. 1-6. HEAT RECOVERY EQUIPMENT .. 1-6. ECONOMIZERS .. 1-7. BLOWDOWN EQUIPMENT .. 1-7. FLASH TANK HEAT Exchanger .. 1-8. BLOWDOWN SEPARATOR .. 1-8. SAMPLE COOLER .. 1-9. Boiler FEEDWATER EQUIPMENT .. 1-9. DEAERATORS .. 1-9. FEED SYSTEMS .. 1-10. Surge Tanks .. 1-10. Pre-Treatment Equipment .. 1-11. Water Softener .. 1-11. CHEMICAL FEEDERS .. 1-12. FLAME SAFEGUARD EQUIPMENT .. 1-13. Stacks .. 1-14. O2 (OXYGEN) TRIM .. 1-14. Chapter 2. Inspections New Boiler Installations.

5 2-1. Hydrostatic Testing .. 2-2. Existing Boiler Installations .. 2-4. Water Side inspection .. 2-4. Fireside Inspection .. 2-5. External Inspection .. 2-6. New or Existing Installations .. 2-6. Burner And Controls .. 2-6. Operating Limits & Interlocks .. 2-7. Auxiliary Equipment .. 2-7. Economizers .. 2-7. Pumps .. 2-8. Blowdown Heat Recovery .. 2-8. Sample Cooler .. 2-8. Deaerator/Surge Tank/Packaged Feed Systems .. 2-8. Filters .. 2-9. Water Softener/Dealkalizer/Reverse Osmosis .. 2-9. Chemical Feeders.

6 2-9. Economizers .. 2-9. Chapter 3. Original Startup INITIAL STARTUP for A New Boiler .. 3-1. Firetube Boiler Boilout .. 3-2. Washing Out Pressure Vessel (Steam) .. 3-3. Washing Out Pressure Vessel (Hot Water) .. 3-3. WATERTUBE BOILOUT .. 3-4. Steam And Hot Water Boilers .. 3-4. fIRING uP .. 3-6. Boiler CONTROLS .. 3-7. Flame Safeguard .. 3-7. Gas Pilot Flame Adjustment .. 3-8. High Limit Control .. 3-8. Operating Limit Control .. 3-8. Modulating Control .. 3-8. Atomizing Media Pressure Switch .. 3-8.

7 Low Fire Hold Control .. 3-8. Low Water Cutoff .. 3-9. Auxiliary Low Water Cutoff .. 3-9. Low Gas Pressure Switch .. 3-10. High Gas Pressure Switch .. 3-10. Combustion Air Proving Switch .. 3-10. Low Oil Temperature Switch .. 3-11. High Oil Temperature Switch .. 3-11. Low Oil Pressure Switch .. 3-11. Bringing Boilers On Line .. 3-11. Chapter 4. Routine Operation NORMAL OPERATION .. 4-1. Boiler Room Care .. 4-1. Basic Record System .. 4-2. Daily Maintenance .. 4-4. Weekly Maintenance .. 4-5. Monthly Maintenance.

8 4-5. Semi-Annual Maintenance .. 4-6. Annual Maintenance .. 4-7. Boiler Room Log .. 4-8. Low Water Cutoff .. 4-9. Safety And Relief Valves .. 4-10. Burner And Controls .. 4-12. Feedwater Treatment .. 4-13. Boiler Blowdown .. 4-13. Deaerator .. 4-15. The Economizer .. 4-16. Feedwater Pump(s) .. 4-17. Fuel Systems .. 4-17. Chapter 5. SHUTTING DOWN. gENERAL .. 5-1. WET STORAGE .. 5-3. DRY STORAGE .. 5-4. Chapter 6. THEORY OF COMBUSTION. AND. THERMODYNAMICS. Introduction .. 6-1. THEORY OF COMBUSTION .. 6-2.

9 Effects of air properties .. 6-6. BASICS OF THERMODYNAMICS .. 6-7. Law of Energy Conservation .. 6-7. Latent Heat of Fusion, Evaporation and Condensation .. 6-7. Analysis of Temperature - Heat Diagram For Water At Constant Pressure .. 6-10. Rated Boiler Output .. 6-12. Factor of Evaporation .. 6-12. Abbreviations .. 15. Chapter 1. General Boiler Description There is a variety of Boiler design concepts available in the marketplace. The material contained in this Guide is directed at users of equipment for commercial or industrial applications.

10 Boilers for these applications are generally of the firetube design or watertube design concepts. The Firetube The firetube Boiler design (see Figures 1-1 & 1-2) uses tubes to direct the Boiler hot gases from the combustion process through the Boiler to a safe point of discharge. The tubes are submerged in the Boiler water and transfer the heat from the hot gases into the water. Inside a firetube Boiler the hot gases travel down the furnace during the combustion process, (first pass). The rear head seals the gases in the lower portion of the head.