BOSS INDUSTRIES 8060 UBI PTO AIR COMPRESSOR …

1 BOSS INDUSTRIES 8060 UBIPTO AIR COMPRESSOROPERATORS, INSTALLATIONS,AND PARTS MANUALP/N: 30034410/08/2009 MCM 2P/N: 300433 OPERATORS AND PARTS MANUALTABLE OF CONTENTSO peration & Maintenance SectionGeneral 5 COMPRESSOR Terminology .. 11 Desription of Components .. 12 Inspection, Lubrication, and Maintenance .. 25 COMPRESSOR Operation .. 28 Parts and Illustration Section .. 31 Recommended Spare 51 Service 52 installation SectionInstructional Procedures .. 54 installation 62 Warranty SectionWarranty 72 3P/N: 300344 GENERAL ARRANGEMENTBOSS INDUSTRIES Underdeck PTO Compressors are shipped in kit form for field kits Screw COMPRESSOR and Mounting Sump with Mounting Coalescer/Air Manifold Oil Inlet Filtration and Necessary Safety and Informational Components10.

2 Parts, Service, installation , and Maintenance INDUSTRIES offers factory installation by qualified technicians, as well as a nationwidenetwork of authorized distributors for field installations, parts and : 300433 SPECIFICATIONSBOSS INDUSTRIES 8060 UBI & 8075 UHBI COMPRESSORT ypical flows based on motor requirements at 2600 psig SUBJECT TO CHANGE WITHOUT PRIOR NOTICE5P/N: 300344 SAFETYWARNINGALL UNITS ARE SHIPPED WITH A DETAILED OPERATORS AND PARTSMANUAL. THIS manual CONTAINS VITAL INFORMATION FOR THE SAFEUSE AND EFFICIENT OPERATION OF THIS UNIT.

3 CAREFULLY READTHE OPERATORS manual BEFORE STARTING THE UNIT. FAILURE TOADHERE TO THE INSTRUCTIONS COULD RESULT IN SERIOUS BODILY INJURYOR PROPERTY COMPRESSOR SAFETY PRECAUTIONSS afety is basically common sense. While there are standard safety rules, each situation has its ownpeculiarities that cannot always be covered by rules. Therefore with your experience and commonsense, you are in a position to ensure your safety. Lack of attention to safety can result in:accidents, personal injury, reduction of efficiency and worst of all - Loss of Life.

4 Watch for safetyhazards. Correct them promptly. Use the following safety precautions as a general guide to safeoperation:Do not attempt to remove any COMPRESSOR parts without first relieving the entire system not attempt to service any part while machine is THE COMPRESSOR SUMP OIL LEVEL ONLY WHEN THE COMPRESSORIS NOT OPERATING AND SYSTEM IS COMPLETELY RELIEVED OF SERVICE VALVE TO ENSURE RELIEF OF SYSTEM AIR PRESSURE WHENPERFORMING MAINTENANCE ON COMPRESSOR AIR/OIL SYSTEM. FAILURETO COMPLY WITH THIS WARNING MAY CAUSE DAMAGE TO PROPERTYAND SERIOUS BODILY not operate the COMPRESSOR at pressure or speed in excess of its rating as indicated in COMPRESSOR Specifications.

5 Periodically check all safety devices for proper not play with compressed air. Pressurized air can cause serious injury to cleanliness during maintenance and when making repairs. Keep dirt away from parts bycovering parts and exposed : 300433 SAFETYDo not install a shut-off valve between the COMPRESSOR and COMPRESSOR oil NOT USE BOSS INDUSTRIES COMPRESSOR SYSTEMS TO PROVIDEBREATHING USAGE, WHETHER SUPPLIED IMMEDIATELY FROM THE COMPRESSORSOURCE, OR SUPPLIED TO BREATHING TANKS FOR SUBSEQUENT USE, CANCAUSE SERIOUS BODILY INDUSTRIES DISCLAIMS ANY AND ALL LIABILITIES FOR DAMAGE FORLOSS DUE TO PERSONAL INJURIES, INCLUDING DEATH.

6 AND/OR PROPERTYDAMAGE INCLUDING CONSEQUENTIAL DAMAGES ARISING OUT OF ANY BOSSINDUSTRIES COMPRESSORS USED TO SUPPLY BREATHING not disconnect or bypass safety circuit not install safety devices other than authorized BOSS INDUSTRIES replacement all openings and replace all covers and guards before operating COMPRESSOR , rags, or loose parts must not be left on the COMPRESSOR or drive not use flammable solvents for cleaning combustibles out of and away from the COMPRESSOR and any associated owner, lessor, or operator of the COMPRESSOR are hereby notified and forewarned that anyfailure to observe these safety precautions may result in damage or INDUSTRIES expressly disclaims responsibility or liability for any injury or damage causedby failure to observe these specified precautions or by failure to exercise that ordinary caution anddue care required when operating or handling the COMPRESSOR , even though not expressly : 300344 SAFETYA compliment of warning decals is supplied with each unit.

7 These decals must be affixed to thevehicle after it has been painted, trimmed, and undercoat, etc. and prior to being put into decals shall be placed so as to be clearly visible to the user and service personnel. (Figures 1through 6.)Figure 1. To be placed on visoror dash near start-up ; 300039 Figure 2. To be placed on body nearoil sump filler : 3000388P/N: 300433 SAFETY figure 3. To be placed on body nearair service : 300040 Figure 4. To be placed on body nearcompressor mounting : 3000439P/N: 300344 SAFETY10P/N: 300433 SAFETY COMPRESSOR FLUID USE AUTOMATIC TRANSMISSION FLUID DEXRON III OR EQUIVALENT.

8 1. CHECK FLUID LEVEL WITH TRUCK OFF AND PARKED ON LEVEL GROUND BEFORE STARTING COMPRESSOR . 2. ADD FLUID IF NONE IS SHOWING IN SIGHTGLASS. 3. DO NOT FILL ABOVE LINE ON SIGHTGLASS 30004711P/N: 300344 COMPRESSOR TERMINOLOGYAT F - Automatic transmission COALESCER - Performs second stage separation of oil from compressed air feedingair tools. Sometimes referred to as the separator - Refers to the volume of compressed air being produced expressed as cubic feet of air CONTROLLER - Sometimes referred to as the engine speed SUMP - The first stage of oil separation from compressed air.

9 Also serves as reservoir areafor COMPRESSOR lubricant and sometimes referred to as the receiver - Refers to the operating pressure the system is set up at, expressed as pounds per VALVE - A valve located on the oil sump which opens in case of excessive referred to as the pop-off or pressure relief SWITCH - Works in conjunction with a temperature and pressure switchgauges,sending a signal to stop the COMPRESSOR power source in cases of high temperature or MOUNT PTO - Power take off gearbox that bolts to the side of the transmission.

10 ThePTO input gear with one of the gears in the vehicle s transmission. The rotation developed by theengine drives the transmission which turns the PTO gear box and rotates the PTO output shaft,driving the GEAR ASSEMBLY: SIDE MOUNT PTO - The adapter gear assembly and theside mount PTO are assembled to the side of the transmission. Typically a PTO box installed on amanual transmission will require an adapter gear assembly in order to obtain the proper enginerotation required by the COMPRESSOR . Most automatic transmissions utilize engine rotation PTO Boss INDUSTRIES Inc.