CCD Black-and-White Video Camera Module

1 A-BX7-100-11 (1). CCD Black-and-White Video Camera Module Technical Manual XC-56. 2004 Sony Corporation Table of Contents Overview Features .. 3. System Components .. 4. Connection Diagram .. 4. Location and Function of Parts and Controls .. 5. Front/Top/Bottom .. 5. Rear Panel .. 6. Mode Settings Input/Output Specifications .. 8. External HD/VD Input Phase Specifications .. 8. HD/VD Output Specifications .. 9. VD Input Specifications .. 9. HD Input Specifications .. 9. Trigger Pulse Specifications .. 9. Video Output Modes .. 10. Binning OFF .. 10. Binning ON .. 10. About the Electronic Shutter .. 11. DIP Switches on the Rear Panel.

2 11. Normal Shutter .. 11. External Trigger Shutter .. 12. Restart/Reset .. 13. To Set Restart/Reset Mode .. 13. To Use High-rate Scan Mode (A) .. 14. External Trigger Shutter .. 16. To Set the External Trigger Shutter .. 17. To Use High-rate Scan Mode (B) .. 18. Timing Chart .. 20. Specifications Main Specifications .. 28. Spectral Sensitivity Characteristics (Typical Values) .. 29. CCD Output Waveform Timing Chart .. 30. Dimensions .. 32. Appendix Available Accessory Lenses .. 33. XC-56 2. Overview Overview The XC-56 is a Black-and-White Video Camera Module Electronic shutter using a CCD (Charge Coupled Device) image sensor.

3 You can choose from FL (flickerless) mode and a wide range of image speeds (1/125 to 1/15,000 s) for the best match to shooting conditions. Features External trigger shutter function (1/4 to High image quality 1/100,000 s). The 330,000-pixel VGA-compatible 1/3 type CCD You can obtain a freeze picture by inputting an image sensor delivers detailed images with the external trigger. This function is useful for shooting a equivalent of VGA resolution (647 493 pixels). The fast-moving object clearly. CCD has square pixels, eliminating the need for aspect ratio conversion. High-rate scan Various mode settings By limiting the number of effective image output lines, you can obtain image output at high frame rates, Rear panel switches allow the following mode settings.

4 Suitable for high-speed image processing. Gain: Fixed/Manual Read mode: Normal (30 fps)/Binning (60 fps). High-rate scan Binning function Synchronized input/output 75 termination Video signals combining vertically adjacent pixels can Shutter modes: Normal/Trigger shutter be obtained at 60 fps. Shutter speed Mounting holes External synchronization Mounting screw holes are provided on the reference The Camera Module automatically determines whether plane on the lower surface of the body, allowing to operate in interlace or non-interlace mode from HD mounting for minimum deviation in the optical axis. (horizontal drive) and VD (vertical drive) signals input for external synchronization.

5 The connector complies with the 12-pin assignment used by the XC-55. Sync signal output The pin assignment is compatible with the existing You can output HD and VD signals from a 12-pin model, the XC-55. connector by changing the setting of a rear panel switch. XC-56 3. Overview System Components The XC-56 Video Camera Module system comprises the following components. Video Camera Module Camera cables Camera adaptor Junction box XC-56 CCXC-12P02N(2 m) DC-700/700CE JB-77. CCXC-12P05N(5 m). CCXC-12P10N(10 m). CCXC-12P25N(25 m). C-mount lenses VCL-50Y-M. Tripod adaptor VCL-25Y-M Close-up ring kit VCT-333I VCL-16Y-M LO-77 ERK.

6 (Insulated type) VCL-12YM. VCL-08YM. Connection Diagram C-mount lens Video OUT. HD/VD Stable power TRIG* source VCL-08YM DC AC. 12 V. Junction box XC-56. VCL-12YM JB-77. AC. Video OUT. HD/VD. VCL-16Y-M. Camera cables CCXC-12P02N Camera adaptor CCXC-12P05N DC-700/700CE. Tripod adaptor CCXC-12P10N (Conforms to new EIAJ 12-pin VCL-25Y-M. VCT-333I CCXC-12P25N assignments). VCL-50Y-M. Close-up ring kit LO-77 ERK. * If you intend to operate the Camera using a trigger pulse, you cannot use the DC-700/700CE. Use the JB-77 Junction Box and a commercially available stable power source, and input a trigger pulse to the CLOCK OUT jack on the JB-77.

7 XC-56 4. Overview Location and Function of Parts and Controls Front/Top/Bottom 1 Lens mount (C-mount). 2 Reference holes (at the top). 3 Reference holes/Tripod screw holes (at the bottom). 4 Reference holes (at the bottom). 1 Lens mount (C-mount) 3 Reference holes/Tripod screw holes (at the Attach any C-mount lens, such as the VCL-12YM bottom). standard lens, or other optical equipment. These precision screw holes are for locking the Camera Module . Locking the Camera Module using these holes Note secures the optical axis alignment. The lens must not project more than 7 mm (9/32 inch) You can install the Camera on a tripod.

8 To install on a from the lens mount. tripod, you will need to install the VCT-333I tripod adaptor using the reference holes on the bottom of the 2 Reference holes (at the top) Camera . These precision screw holes are for locking the Camera Module . Locking the Camera Module using these holes 4 Reference holes (at the bottom). secures the optical axis alignment. These precision screw holes are for locking the Camera Module . Locking the Camera Module using these holes secures the optical axis alignment. XC-56 5. Overview Rear Panel 1 Video OUT/DC IN/SYNC connector 1. 2 2 Shutter speed / mode setting DIP switches 3. 4.

9 5. 3 HD/VD signal input/output switch 4 M GAIN control knob 5 75 termination switch Note switches are for normal operation (restart/reset Be sure to turn the power off before making switch and external trigger shutter OFF). settings. For more information, see Restart/Reset (page 13). and External Trigger Shutter (page 16). When flipping/adjusting the switches/knobs (2 to 5), use screwdrivers that are appropriate for the parts of 4 Gain switch (bit 9). the system which you intend to adjust. Otherwise, This switch selects FIX (fixed) or MANUAL. malfunctions may occur. (manual adjustment) (factory setting: FIX (left side)).

10 1 Video OUT/DC IN/SYNC ( Video output/DC. power/sync input signal) connector (12-pin 5 Binning mode switch (bit 0). connector) Switches the Video signal output mode between Connect a CCXC-12P05N Camera cable to this binning OFF and binning ON (factory setting: connector to obtain power from the +12 V DC power OFF). supply and also to enable Video signal output from the For more information, see Video Output Modes . Camera Module . When a sync signal generator is (page 10). connected to this connector, the Camera Module is synchronized with the external sync signals (HD/VD 3 HD/VD signal input/output switch signals).