CCW-PRIMERS - DP Products Inc. - Products

1 CCW-PRIMERSFOR USE WITHSHEET MEMBRANESCCW-702 PRIMERCCW-702 is a quick drying, solvent based, high-tackprimer specifically designed to promote maximum adhe-sion of CCW Sheet Membrane Waterproofing by long nap roller or brush in an even film at 300 to350 square feet per gallon. Allow primer to dry for 20 min-utes minimum at 75 F. Porous substrates require re-duced coverage rates for proper adhesion. primer has asatisfactory cure when surface is tacky, but will not trans-fer when touched. Prime only areas to be waterproofedthe same day. Reprime if area becomes dirty or wet. Whenused in adverse climactic conditions ( humid, cool,etc.)

2 Or on a porous substrate, additional time will be DATAPACKAGING5 Gallon pails, 45 pails per palletStore at 35o to 110oF (2o to 43oC)CAUTION: Flammable liquid and vapors. Use only withadequate ventilation and avoid breathing vapors. Refer toMSDS for other important warnings and product per Contents46% by Content450 g/lColorBlueFlash Point-4o F, -20o CAdhesion to Application Temperature25 F ( C)Viscosity200cpsStorage Temperature35 F to 110 FPROPERTYRESULTSPROPERTYRESULTSW eight per Content35% 2% by PointN/AAdhesion to Application Temperature40 F ( C)Viscosity60 - 90 cpsStorage Temperature35 F to 110 FPACKAGING1 gallon pails; 180 pails per pallet (45 ct.)

3 [4-1 gal.])5 gallon pails; 36 pails per palletDo not store CCW AWP in direct sunlight or attemperatures above 110 F (43 C) or below 35 F (2 C).Improper storage could lead to product : Avoid contact with eyes and skin. In the eventof contact, wash off immediately. Refer to MSDS for otherimportant warnings and product safety AWP WATER-BASED PRIMERCCW AWP is a single component latex-based AWP is an accessory product to the CCW MiraDRI860/861 sheet membrane and is designed to set thedust on concrete and block surfaces, to promote adhe-sion of the CCW waterproofing membrane to the AWP should be spray applied at a coverage rateof 400 ft ( m ) per gallon ( liters).

4 Several typesof sprayers Airless, Air Assist, Hudson may be used.(CCW AWP may also be applied using a roller. How-ever, caution must be taken not to apply excess primerwhich could cause longer drying times.) Normal dryingtime will be approximately 30 minutes depending on jobsite conditions. Upon curing, CCW AWP will not trans-fer when touched. Surfaces exposed for more than 24hours must be reprimed as they may collect dust andother contaminants causing adhesion should be applied at temperatures above 40 F( C).TECHNICAL DATAC oatings & WaterproofingCCW-715 DAMP CONCRETE PRIMERCCW-715 primer is designed to allow adhesion of CCWS heet Membranes to damp or partially cured concretesurfaces.

5 This allows installation of membrane as soonas forms are removed. Do not apply where visible wateris present. Trapped water may cause blistering, keepdirect sunlight off membrane and backfill by long nap roller or brush in an even film at 300 to350 square feet per gallon. Allow primer to dry for 1 hourminimum at 75o F. primer has a satisfactory cure whensurface is tacky, but will not transfer when touched. Primeonly areas to be waterproofed and backfilled the sameday. Reprime if area becomes dirty or Gallon pails, 45 pails per palletCAUTION: Flammable liquid and vapors. Use only withadequate ventilation and avoid breathing vapors.

6 Refer toMSDS for other important warnings and product Coatings & Waterproofing Incorporated900 Hensley LaneWylie, Texas 75098 Toll Free: (800) 527-7092 Website: is a trademark of Carlisle Corporation 2002 Carlisle CorporationCCW Sheet Membrane Primers 04/04 tcCCW-714 WATER-BASED PRIMERA single component, water-based primer specifically de-signed to condition surfaces and to promote adhesionof CCW Sheet Membrane Waterproofing by spray or long nap roller in an even film at 400to 600 square feet per gallon. Porous substrates willrequire more primer . CCW Sheet Membrane will not ad-here properly to undercured primer ; all moisture mustbe allowed to leave the primer .

7 Allow 25 minutes mini-mum at 75oF. When used in adverse climactic condi-tions ( humid, cool, etc.) or on a porous substrate,additional time will be per Content46% by Content 450 g/lColorGreenFlash Point-4o F, -20o CAdhesion to concrete7 in. Temperature35 F to 110 FTECHNICAL DATAPACKAGING1 Gallon pails, 100 pails per pallet5 Gallon pails, 45 pails per palletStore at 35o to 110oF (2o to 43oC)CAUTION: Avoid contact with eyes and skin. In theevent of contact, wash off immediately. Refer to MSDSfor other important warnings and product safety per Content32% by PointN/AAdhesion to Application Temperature40 F ( C)Viscosity45cpsStorage Temperature35 F to 110 FTECHNICAL DATALIMITED WARRANTYCARLISLE COATINGS & WATERPROOFING INCORPORATED (CARLISLE) warrants this product to be free of defects in workmanshipand materials only at the time of shipment from our factory.

8 If any CARLISLE materials prove to contain manufacturingdefects that substantially effect their performance, CARLISLE will, at its option, replace the materials or refund its limited warranty is the only warranty extended by CARLISLE with respect to its materials. There are no other warran-ties, including the implied warranties of merchantability and fitness for a particular purpose. CARLISLE specifically dis-claims liability for any incidental, consequential, or other damages, including but not limited to, loss of profits or damagesto a structure or its contents, arising under any theory of law dollar value of CARLISLE S liability and buyer s remedy under this limited warranty shall not exceed the purchase priceof the CARLISLE material in question.