CISCO ISR 4000 SERIES ROUTER DATASHEET
Information Export (IPFix) ☆Network monitoring and accounting tools. PRODUCT SPECIFICATIONS OF CISCO 4000 INTEGRATED SERVICES ROUTER Technical Specifications Cisco 4461 Cisco 4451 Cisco 4431 Cisco 4351 Cisco 4331 Cisco 4321 Cisco 4221 Aggregate Throughput 1.5Gbps 1 Gbps to 2 Gbps 500 Mbps to 1 Gbps 200 Mbps to 400 …
Link to this page:
Documents from same domain
Catalyst 6500-E Series Chassis supports all the Cisco Catalyst 6500 Supervisor Engines up to and including the Cisco Catalyst 6500 Series Supervisor Engine 2T, and associated LAN, WAN, and services modules.
–>>Get the Best Prices on Catalyst 6500 Series and Catalyst 6800 Series Note: *1Search for EOL6869 at cisco.com. *2 Search for EOL8162 at cisco.com. Search for EOL8168 at cisco.com. *3
When equipped with the optional isco FlexStack Plus Module (2960X-STA K), the LAN ase/IP Lite models of the isco atalyst 2960-X Series support connection of up to eight switches in …
Cisco Catalyst 2960-X and 2960-XR Series console cables: CAB-CONSOLE-RJ45 Console cable 6 ft. with RJ-45 CAB-CONSOLE-USB Console cable 6 ft. with USB Type A and mini-B connectors Power The internal power supply is an auto-ranging unit and supports input voltages between 100 and
The Cisco 4000 Series Integrated Services Routers (ISR) revolutionize WAN communications in the enterprise branch. With new levels of built-in intelligent network capabilities and convergence, the routers specifically address the growing need for application-aware networking in distributed
Cisco® 1100 Series Integrated Services Routers (ISRs) with Cisco IOS® XE Software combine Internet access, comprehensive security, and wireless services (LTE Advanced 3.0 wireless WAN and 802.11ac wireless LAN) in a single, high-performance device.
and circuits that would otherwise be necessary in IP phone and WLAN deployments. With Cisco Catalyst 9200 Series switches, PoE+ power allocation is dynamic, and power mapping scales up to a maximum of 1440W of PoE+ power. Perpetual PoE is supported on Cisco Catalyst 9200 Series switches, and maintains the PoE+ power during a switch reload.
Cisco® Catalyst® 2960-X Series Switches are fixed-configuration, stackable Gigabit Ethernet switches ... 2960-X LAN Lite 2960-X LAN Lite Forwarding bandwidth 50 Gbps 108 Gbps Switching bandwidth 100 Gbps 216 Gbps Maximum active VLANs 64 …
Router-switch.com 6 Humidity 5 to 95% RH Altitude 15,000 ft (4,570m) Regulatory Compliance Safety UL 60950-1 CAN/CSA C22.2 No. 60950-1 EN 60950-1 AS/NZS 60950-1 IEC 60950-1 EMC 47 CFR, Part 15 ICES-003 Class A
The HPE ProLiant DL380 Gen9 Server delivers the best performance and expandability in the Hewlett Packard Enterprise 2P rack portfolio. Reliability, serviceability and near continuous availability, backed by a comprehensive warranty, make it ideal for any environment. Deploy the data center standard.
2. Ordering Information EFM8LB12 F 64 E – A – QFN32R Tape and Reel (Optional) Revision Packa ge Type S1 SMBus Bootloader (S) and Bootloader Revision (0 or 1) (Optional) Temperature Grade E (-40 to +105) Flash Memory Size – 64 KB Memory Type (Flash) Family Feature Set Laser Bee 1 Family Silicon Labs EFM8 Product Line Figure 2.1. EFM8LB1 ...
documents for product information on the SAM9X60 and the DDR2/SDR-SDRAM memories are listed in Reference ... SDCard, SPI or QSPI Flash. Bootloader features selectable by OTP bits. • 96-Kbyte ROM for NAND Flash BCH ECC table – DDR2-SDRAM memory up to 1 Gbit or 64-Mbit SDR-SDRAM memory, 16-bit data bus ...
The MICROSAR.OTA solution is described in the MICROSAR Product Information while this document covers the Vector Flash ... Flash Bootloader . 5 . 1.1 Advantages > Efficient and reliable reprogramming of ECUs supporting all common vehicle bus systems like CAN, Ethernet, FlexRay and LIN using UDS diagnostic protocol > Available for most OEMs and ...
This document applies to the STM32 products embedding bootloader versions V3.x, V4.x, V7.x, V9.x, V10.x and V13.x as specified in AN2606 “STM32 microcontroller system memory boot mode ” (available on www.st.com), which also contains more information about the USB hardware resources and requirements for the device bootloader. These products
Product data sheet Rev. 2.0 — 1 April 2022 2 of 165 NXP Semiconductors RT600 Dual-core microcontroller with 32-bit Cortex-M33 and Xtensa HiFi4 ... I2C, UART, Octal/Quad SPI Flash, HS USB or eMMC via on-chip bootloader software included in ROM. Digital peripherals: Two general purpose DMA engines, each with 32 channels and up to 25
Gets the bootloader version and the Read Protection status of the Flash memory Get ID (1) 0x02 Gets the chip ID Speed 0x03 The speed command allows the baud rate for CAN run-time to be changed. Read Memory (2) 2. Refer to STM32 product datasheet and AN2606 to know the memory spaces valid for these commands. 0x11
Bootloader Design for MCUs in Embedded Systems Rev June 26, 2015 A2 ... During the initial stages of product development it is very common for the boot-loader to be ... programmer have to dig into flash programming but there is also a need to do a deep dive into memory maps, re-locatable vector tables, copy down functions, flash partitioning ...
8 kB (LPC1111), or 4 kB (LPC1110) on-chip flash programming memory. 256 byte page erase function (LPC1100XL series only) 8 kB, 4 kB, 2 kB, or 1 kB SRAM. In-System Programming (ISP) and In-Application Programming (IAP) via on-chip bootloader software. LPC1110/11/12/13/14/15 32-bit ARM Cortex-M0 microcontroller; up to 64 kB flash and 8 kB SRAM