CLAM Engineering by TURN OUT ENGINEERING Pty Ltd

1 CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: Introduction The installation of pipe line strainers is essential for the protection of such valuable and important equipment as valves, control equipment, instruments, pumps, regulators etc.

2 Tremendous savings in unit replacement, shut down time and maintenance costs are assured. Note: But only when the correct size of perforation or mesh is used in the element or basket fitted in the strainer. Body selection: Pressure Temperature Product and plant conditions Materials available: Bronze SG Cast Iron Cast steel Forged carbon steel Stainless steel Screen selection: 304/316 S/S perforated sheet metal and woven wire are available to 5 micron. Standard Perforations available for any CLAM strainer: Interlining Mesh available for any CLAM Y Strainer Plain Weave mesh Hollander Weave Mesh ( 8mesh to 400mesh ) ( 200micron to 5micron ) 5mm 4mm 1mm CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: 'S' Type Filters Designed primarily for use on gas metering sets, the CLAM range of 'S' type filters allows for mounting in a vertical situation and flow is upward.

3 The declined body section ensures entrapment of contaminants in the sump cover. Maximum pressure: 2500 KPa at 121 C to AS 1271. Standard construction materials: Body: AS 1565/C83600 (LG2) Casting. Sump cover: 25mm Unit: AS 1568-C37710 Brass Forging. Sump cover: 32mm Unit: JIS H3250 C3604BD Brass Machined. Sump cover seal: Dowty type bonded washer. Element: 25mm Unit: Acetal end rings, thermally bonded to continuous seam welded stainless steel Hollander weave cloth. Element: 32mm Unit: Steel Rings spot welded to Perforated support Basket, Interlined with Stainless Steel Hollander Weave Cloth. Features: Filter elements available to 5micron. Threads available: BSPT and NPT Male Standard unit comes complete with NPT Petes plugs. Typical Pressure drop: Filtration: 100 microns.

4 Medium: Air at 20 C. Flow rate: 2000 l/min. Pressure drop: 1 KPa. Filter dimensions UNIT DIMENSIONS DN 25 DN 32 OVERALL HEIGHT (H) 140 140 OVERALL LENGTH (L) 140 175 CENTRE TO CENTRE (C) 76 76 MINIMUM For ELEMENT REMOVAL (R) 25 30 UNIT WEIGHT 2kg SPARE PARTS ELEMENT SE3S SE42S GASKET ( Dowty ) G017 G033 CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: 25, 40 and 50mm Screwed BSP/NPT bronze 'Y' Strainers Standard construction materials: Body: AS1565/C83600 (LG2) Casting.

5 Cover; 25mm unit: AS 1568 - C37710 Brass Forging. Cover; 40mm & 50mm units: AS1565/C83600 (LG2) Casting or JIS H3250 C3604BD Brass Machined. Cover gasket: Compressed Fibre Element: 304/316 stainless steel Features: Filter elements available to 5micron. Threads available: BSPT and NPT female. Unit can be fitted with Petes plugs Maximum pressure: Cold non-shock; 2500 KPa at 121 C: AS1271. Steam; 1725 KPa at 260 C: AS1271. Perforated Stainless Steel elements with , 1, , 2, 3, 4 or 5mm perforations are standard, however, for finer filtration requirements; woven stainless steel to 5 micron is available. Where woven wire of less than 150 micron is employed, O-rings are fitted to element ends to ensure a perfect seal. All elements have surface areas exceeding 10 times the nominal bore size to minimize pressure drop.

6 NOMINAL BORE (mm) DIMENSION 25mm 32mm 40mm 50mm O/All Length (L) 114 134 134 175 Height(A) 81 124 124 159 Min Height for Element Removal (H) 102 153 153 203 Unit Weight 6kg SPARE PARTS Strainer Element SE3 SE26 SE26 SE15 Gasket G11 G60 G60 G75 O-Ring ( Nitrile/Viton ) BS022 BS127 BS127 BS133 SCREWED CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: Screwed, AS 2129 Tables D E F or ANSI 125/150 SG iron 'Y' Strainers Standard construction materials: Body: AS 1831 Gr.

7 400/15 SG Iron Casting. Cover: AS 1831 Gr. 400/15 SG Iron Casting. Gaskets: Up to 100mm units; 316 Spiral Wound & Graphite Filled. 150 & 250mm units: Compressed Fibre. Element: 304/316 stainless steel. Perforated S/S elements with , 1, , 2, 3, 4 or 5mm perforations are standard, however, for finer filtration requirements; woven stainless steel to 5 micron is available. Where woven wire of less than 150 micron is employed, O-rings are fitted to element ends to ensure a perfect seal. All strainers have surface areas exceeding 10 times the nominal bore size to minimize pressure drop. NOMINAL BORE (mm) DIMENSION MODEL 32 40 50 65 80 100 150 250 Screwed BSP/NPT 134 134 175 O/All Length (L) Flanged 242 242 254 337 337 419 540 765 Height (A) All Models 124 124 143 197 197 273 420 620 Min Height for Element Removal (H)

8 All Models 146 146 184 254 254 330 500 700 Screwed 4kg 4kg 6kg APPROX WEIGHT Flanged 10kg 30kg 30kg 40kg 110kg 275kg SPARE PARTS (all models) Screwed SE26 SE26 SE15 Strainer Element Flanged SE4 SE4 SE7 SE8 SE8 SE9 SE24 SE29 Screwed G60 G60 G75 Gasket Flanged G21 G21 G24 G25 G25 G26 G150 G65 SCREWED FLANGED CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph: 03 5977 3874 Fax: 03 5977 3499 Email: 15, 20 and 25mm A105 forged carbon-steel 'Y' Strainers Standard construction materials Body: ASTM A105 Forging Cover.

9 ASTM A105 Forging Bolting: ASTM A193 Gr. B7 Studs and ASTM A194 Gr. 2H Nuts Gaskets: 316 S/S Spiral Wound & Graphite Filled Flanges: ASTM A105 Forgings Element: 304/316 stainless steel Perforated S/S elements with , 1, , 2, 3, 4 or 5mm perforations are standard, however, for finer filtration requirements; woven stainless steel to 5 micron is available. Where woven wire of less than 150 micron is employed, O-rings are fitted to element ends to ensure a perfect seal. NOMINAL BORE (mm) DIMENSION MODEL 15 20 25 Screwed BSP/NPT 133 133 133 Socket Weld 133 133 133 Butt Weld 150 150 150 SCREWED/SOCKET WELD/BUTT WELD Flanged ANSI 150# & 300# 200 200 200 Flanged ANSI 600# 216 216 216 O/All Length (L) Flanged ANSI 900#/1500# 260 260 260 Height (H) All Models 108 108 108 Min Height for Element Removal (R) All Models 127 127 127 SPARE PARTS (all models) Part No: Strainer Element SE13 CL150#, 300# and 600# G66 Gasket CL900# and 1500# G92 O-Ring: Nitrile / Viton also available ) BS122 FLANGED CLAM ENGINEERING by TURN OUT ENGINEERING Pty Ltd 2011 CLAM Australian manufacturers of quality pipeline products Ph.

10 03 5977 3874 Fax: 03 5977 3499 Email: CL 150# cast carbon-steel 'Y' Strainers Standard construction materials: Body: ASTM A216 Gr. WCB Casting Cover: ASTM A105 Forging Bolting: ASTM A193 Gr. B7 Studs and ASTM A194 Gr. 2H Nuts Gaskets: 316 S/S Spiral Wound & Graphite Filled Flanges: ASTM A105 Forgings Element: 304/316 stainless steel Perforated S/S Elements with , 1, , 2, 3, 4 or 5mm perforations are standard, however, for finer filtration requirements; woven stainless steel to 5 micron is available. Where woven wire of less than 150 micron is employed, O-rings are fitted to element ends to ensure a perfect seal.