Compliments of SwatchBattery

1 HowTo_2002 4/18/02 9:09 AM Page 1 Compliments of at the bto the picturtypes, or IF IWATCH, REFESTEP1 Look at t!YOU WILL NEEDT oolsCase Holding ViseCase WrenchWatch Closing Hand PressPolishing ClothEWB-1 Battery TesterCase KnifePlastic TweezersSmall ScrewdriverFine-pointTweezersHowTo_2002 4/18/02 9:10 AM Page 2 Look at the back of the customer s watch and compare it to the pictures below. If it does not match any of these types, or IF IT IS A SPECIALIZED OR WATER RESISTANT WATCH, REFER IT TO A PROFESSIONAL the watch looks similar to this, follow the step-by-step instructions contained in the RED section labeled SNAP at the !!If the watch looks similar to this, follow the step-by-step instructions contained in the BLUE section labeled HATCH the watch looks similar to this, follow the step-by-step instructions contained in the green section labeled SCREW BACK1 HowTo_2002 4/18/02 9.

2 10 AM Page 3 SNAP BACKP lace watch in the case holding viseClamp the watch in the case holding vise byopening the two halves of the block, placing thewatch in the middle and gently release or tightenthe two halves so that they hold the watch the watch band does not unbuckle or unclasp,separate the band by pressing down with a pointed tool to removethe spring loaded pin that connects the band to the clasp or case backs are snapped on andcan be removed by inserting a bladeinto the appropriate notch of the caseor case back and twisting the handleof the tool to pop off the no groove is provided, be surea sharp knife is inserted into thenarrow slot between the back andthe case. Once the knife is firnly inthe groove, a slight twist of the knifehandle will pop off the the tool tosnap off needed:Case knifeIMPORTANT: Beforeremoving battery(s),be sure to note whichside is up.

3 You willhave to put the newEnergizer battery inexactly the same some watches, thebattery is held in bysmall metal clips. If so, carefully followthe directions to theright for removing thevarious types of plastic tweezersto remove battery(s).SPRING CLIP:Lift up one end of the metalclip with the fine-pointtweezers. It will come remove the CLIP:Remove the screws with the small screwdriver. BECAREFUL NOT TO LOSE THEM!CAUTION: CLIP MAY SPRINGOUT. MAINTAIN PRESSURE ORSCREW MAY BE needed: Fine-PointTweezers, SmallScrewdriver, PlasticTweezersPERMANENT CLIP:Lift the outside edge of the batteryout of its compartment with thesmall the battery tester for operating instructions. IMPORTANT: If the watch hastwo batteries and only one tests replace , replace both batteries.

4 If bothbatteries test good , there is something wrong with the watch. Refer it to aprofessional the back3 STEPR emove the battery4 STEPTest the batteries5 STEPT ools needed: EWB-1 Battery Tester HowTo_2002 4/18/02 9:10 AM Page 4 SNAP BACKHATCH BACKRead the number on the old battery and replace with the same or correspondingEnergizer Watch Battery. Refer to the current Energizer Watch/Electronic BatteryReplacement Guide or the Energizer battery size checker to find the correctEnergizer battery type the battery compartment for dirt and remove it. If you find corrosion, refer watch to aprofessional : Be sure to testthe new battery beforeinstalling. For tester setting,follow manufacturer sinstructions. Use plastictweezers to install the newEnergizer battery(s) with thesame side up as the one(s)you replaced.

5 Remember,the watch won t work if thebattery(s) are put in :If there is a rubber sealing gasket in the back of the watch,make sure it is lined up properly before closing back. Snap a metaladapter that is slightly smaller than the watch back into the upper jawof the press. Place the support plate into the bottom of the press and fita plastic ring adapter large enough to hold the watch on the supportplate. Place the watch face down into the plastic ring adapter and pressgently on handle until watch back snaps into the watch and make sure it is working. Inanalog watches, if there is no second hand,observe the minute hand through a magnifyingglass until you see CLIP:Place one end of spring clip in place and firmly pushthe other end into its sure spring clip is in theslot to avoid bent spring CLIP: Place the clip over the new Energizer battery.

6 Holdthe screw with the fine point tweezers to start it in thehole. Tighten the needed: Small ScrewdriverFine Point TweezersPlastic TweezersTools needed: Watch ClosingHand Press3 Locate replacement battery6 STEPC lean the battery compartment7 STEPI nstall the new Energizer battery8 STEPC lose the watch9 STEPC lean the watch10 STEPR eset the watch11 STEPC rossReferenceGuide341011987 Gently wipe the watch to remove anyfingerprints or needed: Polishing clothHowTo_2002 4/18/02 9:10 AM Page 5 HATCH BACKTool needed: Plastic TweezersPlace watch in the case holding viseClamp the watch in the case holding vise byopening the two halves of the block, place thewatch in the middle and gently release or tightenthe two halves so that they hold the watch the watch band does not unbuckle or unclasp, separate the band bypressing down with a pointed tool to remove the spring loaded pin thatconnects the band to the clasp or the hatch counter-clockwise byturning a coin in the slot.

7 Once the hatch isloosened, finish unscrewing and remove withfingers. BE CAREFUL NOT TO LET THE BATTERYFALL OUT :Before removing battery(s), be sure to note whichside is up. You will have to put the new Energizer battery inexactly the same way. To remove the battery, simply turn thewatch over and it should fall out. If the battery is stuck, gentlypry it out. Use plastic tweezers to remove battery(s).See the battery tester for operating instructions. IMPORTANT: If the watch has two batteries and only one tests replace ,replace both batteries. If both batteries test good , there is somethingwrong with the watch. Refer it to a professional the hatch3 STEPR emove the battery4 STEPTest the batteries5 STEPTool needed: EWB-1 Battery Tester HowTo_2002 4/18/02 9:10 AM Page 6 HATCH BACKSCREW BACKTool needed: Plastic TweezersRead the number on the old battery and replace with the same or correspondingEnergizer Watch Battery.

8 Refer to the current Energizer Watch/Electronic BatteryReplacement Guide or the Energizer battery size checker to find the correctEnergizer battery type the battery compartment for dirt and remove it. If you find corrosion, refer watch to aprofessional screwing in the hatch with your fingers,then tighten with a the watch and make sure it is working. Inanalog watches, if there is no second hand,observe the minute hand through a magnifyingglass until you see :Be sure to test the new battery before installing. Fortester setting, follow manufacturer s instructions. Use plastictweezers to install the new Energizer battery(s) with the sameside up as the one(s) you replaced. Remember, the watch won twork if the battery(s) are put in replacement battery6 STEPC lean the battery compartment7 STEPI nstall the new Energizer battery8 STEPC lose the hatch9 STEPC lean the watch10 STEPR eset the watch11 STEPC rossReferenceGuide341011987 Gently wipe the watch to remove anyfingerprints or needed: Polishing clothHowTo_2002 4/18/02 9.

9 10 AM Page 7 SCREW BACKP lace watch in the case holding viseClamp the watch in the case holding vise byopening the two halves of the block, placing thewatch in the middle and gently release or tightenthe two halves so that they hold the watch the watch band does not unbuckle or unclasp,separate the band by pressing down with a pointed tool to removethe spring loaded pin that connects the band to the clasp or : Beforeremoving battery(s),be sure to note whichside is up. You willhave to put the newEnergizer battery inexactly the same some watches, thebattery is held in bysmall metal clips. If so, carefully followthe directions to theright for removing thevarious types of plastic tweezersto remove battery(s).SPRING CLIP:Lift up one end of the metalclip with the fine-pointtweezers.

10 It will come remove the CLIP:Remove the screws with the small screwdriver. BECAREFUL NOT TO LOSE THEM!CAUTION: CLIP MAY SPRINGOUT. MAINTAIN PRESSURE ORSCREW MAY BE needed: Fine-PointTweezers, SmallScrewdriver, PlasticTweezersPERMANENT CLIP:Lift the outside edge of the batteryout of its compartment with thesmall the battery tester for operating instructions. IMPORTANT: If the watch hastwo batteries and only one tests replace , replace both batteries. If bothbatteries test good , there is something wrong with the watch. Refer it to aprofessional the battery4 STEPTest the batteries5 STEPT ools needed: EWB-1 Battery Tester Place the Case Wrench metal tips in the watch back counter-clockwise to remove watch backTool needed: Case WrenchLocate the wrench slots on the back of the the back3 STEPHowTo_2002 4/18/02 9:10 AM Page 8 SCREW BACKCROSS REFERENCERead the number on the old battery and replace with the same or correspondingEnergizer Watch Battery.