COMPRESSOR INSTALLATION OPERATION MANUAL

1 OIL FREE AIR & GAS COMPRESSORSCOMPRESSORINSTALLATION & OPERATION MANUALforAmbient Air CompressorsAir BoostersGas CompressorsRev 11/10WI-400-010 APP 1, Rev. 3 THIS PAGE INTENTIONALLY LEFT BLANK3 CONTENTSW arranty ..4 General Information ..5 COMPRESSOR Nameplates ..5 Safety ..6 Introduction to Oil Free Ambient Air Compressors ..7 Introduction to Air Boosters and Gas Compressors ..8 Section 1 - COMPRESSOR Using This MANUAL ..9 Receipt of Location ..9 Foundation ..9 Inlet Piping and Inlet Filtration.

2 10 Discharge Piping ..11 Receivers - Ambient Air Receivers - Air Boosters and Gas Compressors ..12 COMPRESSOR Cooling - Air Cooling ..12 COMPRESSOR Cooling - Water Cooling ..12 COMPRESSOR Control Panel ..13 Unloader Controls ..13 Safety Devices ..17 Plumbing of Air Booster and Gas COMPRESSOR Packings ..18 Section 2 - COMPRESSOR Startup ..25 INSTALLATION Using this MANUAL ..26 Inspection After Extended Storage ..26 COMPRESSOR Speed.

3 26 Crankcase Oil Pressure Regulation ..27 Oil Pump Direction of Rotation ..27 V Belt Tension Settings ..28 Adjustment of MANUAL Unloader Adjustment of Automatic Unloader Additional Controls Adjustment ..32 Pre-Startup Check List ..34 Initial Startup and OPERATION (Ambient Air Compressors) ..34 Initial Startup and OPERATION (Air Boosters and Gas Compressors)..35 Daily Startup Checklist ..26 Section 3 - Maintenance and Troubleshooting ..37 Maintenance Schedule (Ambient Air Compressors).

4 37 Maintenance Schedule (Air Boosters and Gas Compressors) ..37 Troubleshooting ..40 Section 4 - COMPRESSOR Servicing ..43 Torque Settings ..44 Clearances and Tolerances ..45 COMPRESSOR Disassembly ..47 Oil Pump Replacement ..48 Bearing Replacement ..49 COMPRESSOR Assembly ..50 Valve Replacement ..52 Appendix 1 - Tool List ..54 Appendix 2 - COMPRESSOR Storage ..55 4 WARRANTY - GENERALH ycomp warrants that its compressors will be free from defects in material and workmanship for a period of twelve (12) months from the date of compressors which fail within the 12 month period due to defects in material or workmanship, will be repaired or replaced at Hycomp s discretion provided the Purchaser meets all of the applicable requirements of the warranty and none of the limitations parts subject to wear or abuse are not covered by this limited warranty.

5 These may include, but are not limited to, mechanical seals, bearings, piston rings, valves, packings, and other parts showing signs of limited warranty is void if any product or accessory has been serviced or altered by anyone not authorized by Hycomp. Additional warranty limitations apply. Please see complete warranty policy for complete warranty policy for details(available from the factory)NOTICE TO HYCOMP CUSTOMERSH ycomp recommends you order service and replacement parts according to the model number and serial number found on the nameplate of your COMPRESSOR .

6 Do not order parts from the general descriptions in this MANUAL . Ordering directly from Hycomp or a registered vendor will minimize the possibility of receiving incorrect parts for your INFORMATIONNOTICE: Hycomp compressors must only be installed in systems which have been designed by qualified personnel. The system MUST conform to all applicable federal, state, local and national standards. This MANUAL is intended to assist qualified technical personnel in the INSTALLATION , OPERATION and maintenance of Hycomp compressors, and should be kept with the COMPRESSOR at all compressors shall only be serviced and maintained by qualified personnel.

7 Routine inspection and maintenance is highly recommended. This MANUAL covers :Ambient Air Compressors (inlet source is the ambient air surrounding the COMPRESSOR ),Air Boosters (inlet source is elevated air pressure, usually taken from customer s existing plant air system) andGas Compressors (compressors pumping any gas other than air),including the following compressors (by Block):A Block: AN6, AN4A, AN3A, 2AD4A WN4A, Hycomp model has a nameplate attached to the crosshead guide cylinder, usually on the oil-pump end.

8 The information on this nameplate should be available when ordering parts for the COMPRESSOR or requesting assistance with troubleshooting, maintenance, INSTALLATION or contacting Hycomp, note who you purchased the COMPRESSOR from, who installed it, INSTALLATION date, the purchase date, and model number. This will help Hycomp identify your COMPRESSOR and any special parts and materials that may have been used. Fill in the information from the new COMPRESSOR into the spaces provided in the sample nameplate From _____COMPRESSOR NAMEPLATESI nstalled By _____Installation Date_____Purchased Date_____Model #_____Serial #_____Date of Startup_____ B Block: AN12, 2AN8, 2AN7B, 2AN3BC Block: AN20, AN26, WN26, 2AN17, 2WN15, 2AN11C, 2AN10C, 2AN13C, AN10C, AN6C, 2AN3CD Block.

9 AN44, WN44, 2AN26, 2AN35, AN20D, 2AN35, 2WN35, AN12D, AN17D, AN35D, 2AN10D, 2AN15DE Block: WN72, 2AN61, 2AN76, 2WN61, WN14E, AN20E, 2WN13E, 2WN17E, 2WN22E, 2AN22 EFBlock: AN154, AN44F, WN28F, WN98, WN154, 2WN34F, 2AN28F, 2AN137, 2WN150F, 2AN22F, 2WN137F, 2WN49FG Block: 2AN40, 2WN40H Block: 2WN76, WN90, 2AN76V Block: 3AN44V, 3AN11 VDifferences between compressors will be noted in the text.

10 6 Hycomp insures, from the beginning, that safety is designed into every COMPRESSOR . A COMPRESSOR is a precision high speed mechanical piece of equipment. They require caution in OPERATION to minimize hazard to one s self and property. The following is a list of safety precautions that should always be observed:1. Do not try to service any part of the COMPRESSOR or accessory while the unit is The main power disconnect switch must be turned off; lockout/tagout the switch before performing any work or maintenance on the unit, per OSHA Regulation Relieve the system of all pressure before attempting to service any part of the unit, per OSHA Regulation The unit must not be operated with any of its safety guards, shields.