Example: biology

CONCRETE MASONRY & ACCESSORIES | TILT-UP/PRECAST

224 MASONS SUPPLY COMPANY Oregon (800) 537-3407 Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Gresham | Hillsboro | Medford | Portland | Salem | Seattle | Tacoma | Wilsonville | Woodinville | VancouverM A S C O . N E T[ BACK TO ][ BACK TO ] tilt -UPTILT-UP/PRECASTTilt-up 3 systemOffers the tilt -Up contractor an economical, strong method to lift, handle and place CONCRETE tilt -up wall panels. The System features a design that utilizes the same lifting hardware for both face lift and edge lift applications. This system is a high quality, high strength, quick connect Face Lift insertFurnished as an assembly, complete with the strong forged foot insert, wide spread, stable plastic base, floating rebar clip and plastic locator setting plug.

MASONS SUPPLY COMPANY Oregon (800) 537-3407 ♦ Washington (800) 537-6216 TILT-UP

Tags:

  Concrete, Masonry, Accessories, Tilt, Concrete masonry amp accessories tilt

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of CONCRETE MASONRY & ACCESSORIES | TILT-UP/PRECAST

1 224 MASONS SUPPLY COMPANY Oregon (800) 537-3407 Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Gresham | Hillsboro | Medford | Portland | Salem | Seattle | Tacoma | Wilsonville | Woodinville | VancouverM A S C O . N E T[ BACK TO ][ BACK TO ] tilt -UPTILT-UP/PRECASTTilt-up 3 systemOffers the tilt -Up contractor an economical, strong method to lift, handle and place CONCRETE tilt -up wall panels. The System features a design that utilizes the same lifting hardware for both face lift and edge lift applications. This system is a high quality, high strength, quick connect Face Lift insertFurnished as an assembly, complete with the strong forged foot insert, wide spread, stable plastic base, floating rebar clip and plastic locator setting plug.

2 The face lift insert is easy to position and tie to the rebar mat. The rebar clip provides a quick, positive method of fastening the insert to the rebar mat. The clip slips onto the body of the insert where it floats with any movement of the rebar mat, preventing misalignment of the insert due to fluctuations of the rebar lifting hardwareConsists of a clutch body, curved bolt/release arm and high strength bail. The bail is designed to readily align itself to the pull of the rigging. Once the hardware is properly engaged and under load, the hardware cannot be disengaged. Remote ground release is easily accomplished after the load has been relaxed.

3 The hardware is designed to service both face lift and edge lift system conditions. SWL is 15,000 lbs. with an approximate factor of safety of 5 to NOT use with seeded aggregate 1/2" or larger as aggregate may "pop out" during the erection process, resulting in a reduced insert safe working face Lift Insert T-90-CFloating Rebar ClipT-92 Lifting HardwareStructural Panel Thickness5"5-1/2"6"6-1/4"6-1/2"7"7-1/4"7 -1/2"8"Insert Safe Working Load (lbs)8,00010,00012,00012,50013,00015,000 15,00015,00015,000T-90-F Face Lift Insert Selection (lbs)DS (lbs)DS 5FL5" 512FL5-1/2" 6FL6" 612FL6-1/2" 7FL7" 712FL7-1/2" 8FL8" provides a factor of safety of approximately 2 to 1 in 2,500 psi normal weight CONCRETE .

4 Consult manufacturers data on values on shear and reduced edge SUPPLY COMPANY Oregon (800) 537-3407 Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Gresham | Hillsboro | Medford | Portland | Salem | Seattle | Tacoma | Wilsonville | Woodinville | VancouverM A S C O . N E T[ BACK TO ][ BACK TO ] tilt -UPTILT-UP/PRECASTSetBodyLidTop of PanelTop of PanelTop of PanelTilt-Up 3 Hardware in open nested in the insert void and Bolt/Release arm Edge Lift InsertHas an integral shear plate for maximum transfer of shear load into the CONCRETE . The insert is furnished with a disposable recess plug that is used to attach the assembly to the panel form.

5 Make certain that the crane applies the lifting load in a direction toward the top of the panel or perpendicular to the casting bed. DO NOT allow the crane to apply a load toward the bottom of the provides a factor of safety of approximately 2 to 1 in 2,500 psi normal weight CONCRETE . Consult manufacturers data on values on shear and reduced edge crane line should be slackened slightly to permit the release of the lifting release the hardware, apply a quick, even downward force to the release Lift InsertT-90-CRebar ClipStructural Panel ThicknessShearSafe WorkingLoad (lbs.)TensionSafe WorkingLoad (lbs.)4"4,3004,7005"5,2505,9006"6,2007,0 007"7,0508,200T-90 Edge LIft (lbs)DS FL1472 FL1484 FL1498 Recess Plug226 MASONS SUPPLY COMPANY Oregon (800) 537-3407 Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Gresham | Hillsboro | Medford | Portland | Salem | Seattle | Tacoma | Wilsonville | Woodinville | VancouverM A S C O.

6 N E T[ BACK TO ][ BACK TO ] tilt -UPTILT-UP/PRECASTGROUND RELEASE II LIFTING HARDWAREG round Release II Lifting hardware unit offers you, the tilt -up contractor, the latest and easiest to use tilt -up lifting hardware unit on the market today! This new lifting hardware unit is a simplified design and when combined with our Ground Release II Insert provides you with a superior system for the quick and efficient erection of tilt -up CONCRETE wall panels. Bail will accept all conventional crane attachments. Unit moves easily as it follows line of action of crane cable. Lifting Body attaches to head of insert. Whenever diagonal loads are applied to the bail, the result is a combination of a compressive load applied to the CONCRETE and a tension load applied to the insert.

7 Release Line is a " hollow braided Polyethylene Cord of sufficient length to reach the ground. SWL is 15,000 lbs with an approximate factor of safety of 5 to Release II InsertThe Ground Release II System is a unique method of tilting CONCRETE tilt -up wall panels into position and allows the hardware to be easily released from the ground. Ladders are normally not required during the hardware release process which greatly increases worker safety and of the Ground Release II Insert: Flexible Plastic Antenna folds over when screed passes, but springs back to indicate insert location. Plastic Recess Plug creates a void for attaching the Ground Release II Lifting Hardware to the insert head.

8 The expendable plastic recess plug is easily removed from the hardened CONCRETE . Directional Label indicates correct panel thickness and direction of plastic recess plug in relation to top and bottom of panel. Ground Release II Anchor. This hot forged anchor permits rapid hardware attachment and allows smooth rotation of the hardware during the releasing operation. Plastic Support Base is designed to provide maximum support and stability for the Ground Release II Anchor and eliminates any potential rust problems. Ground Release II Inserts are shipped assembled, ready to use and are sized 1/8" less than panel thickness.

9 SWL provides a safety factor of approximately 2 to 1 in 2,500 psi normal weight CONCRETE . Consult manufacturers data on values on shear and reduced edge Ground Release II Insert Selection ChartStructural Panel Thickness5"5 "6"6 "7"7 "8"Ground Relase II Anchor Length3 "4 "4 "5 "5 "6 "6 "Insert Safe Working Load (lbs)8,00010,00012,00013,00015,00015,000 15, (lbs)DS 5GR5" 512GR5-1/2" 6GR6" 612GR6-1/2" 7GR7" 712GR7-1/2" 8GR8" (lbs)DS SUPPLY COMPANY Oregon (800) 537-3407 Washington (800) 537-6216 Clackamas | Eugene | West Eugene | Gresham | Hillsboro | Medford | Portland | Salem | Seattle | Tacoma | Wilsonville | Woodinville | VancouverM A S C O.

10 N E T[ BACK TO ][ BACK TO ] tilt -UPTILT-UP/PRECASTD ouble Ground Release II SystemOver the last few years, Dayton Superior has seen a trend develop towards the use of heavier tilt -up wall panels on many of the tilt -up projects erected in the United States. In an effort to reduce the number of rigging changes required, when these heavier panels are to be erected, Dayton Superior has developed and tested a new, double insert lifting system for increased lifting capacity. This new lifting system consists of two Ground Release II inserts, two Ground Release Lifting Hardware units and the Ground Release II Spreader Beam with twin 8 ton shackles.


Related search queries