Controllers: Honeywell UDC1200L MICRO-PRO …

1 59339-1. 2. SELECT MODE Alarm 2 Type* ?,?0 Options as for alarm 1 24,"* 4. SETUP MODE. Honeywell UDC1200L MICRO-PRO High Alarm 2. universal LIMIT controller product manual (51-52-25-132) Select mode is used to access the configuration and operation menu functions. value* 2@?0 Range Max Note: Configuration must be completed before adjusting Setup parameters. It can be accessed at any time by holding down and pressing . Low Alarm 2 First select Setup mode from Select mode (refer to section 2). The Setup LED. In select mode, press or to choose the required mode, press to enter. value* 2,?0 Range Min will light while in Setup mode. Press to scroll through the parameters, CAUTION: Installation should be only performed by An unlock code is required to prevent unauthorised entry to Configuration, & Setup then press or to set the required value.

2 Band Alarm 2. technically competent personnel. Local Regulations modes. Press or to enter the unlock code, then press to proceed. value* >?,0 6* To exit from Setup mode, hold down and press to return to Select mode. regarding electrical installation & safety must be observed. Note: Parameters displayed depends on how instrument has been configured. Note: At first power-up the message !"#" $"%& is displayed, (see section 6). Dev. Alarm 2. Value* 8?,0 6*. 1. INSTALLATION Access to other menus is denied until configuration mode is completed Alarm 2. Parameter Lower Upper Display Adjustment Default Mode Upper Lower Description Default ?:A0 .* Display Range & Description Value Installing Option Modules Display Display Unlock Hysteresis*. R/max if Codes ,Mm# Limit Output Relay Scaled Range Minimum to $#),=:1. CPU PCB Mounting Struts Operator '(#)* +,$#* Normal operation None ?

3 B48 Alarm 1, Direct Limit Setpoint value +2* scaled Range Maximum R/min if Set Up +-#(* +,$#* Tailor settings to the application ./ ?.4) Alarm 1, Reverse $#),=,". Option Module 1 Option Module A Configuration $"%&* +,$#* Configure the instrument for use 0/ ?048 Alarm 2, Direct 1 LSD to full span in display units, Limit Hysteresis :J+#* . (Fixed Limit Relay) product Info 1%&"* +,$#* Check manufacturing information None ?04) Alarm 2, Reverse on the safe side of the limit SP. ')48 Logical Alarm 1 OR 2, Direct ?B48* OFF or to secs Option Module 2 Option Module 3 Note: The instrument will always return automatically to Operator mode if Input Filter Time Constant &1,#* (see CAUTION note below) there is no key activity for 2 minutes. Output 2 Usage C+=0 ')4) Logical Alarm 1 OR 2, Reverse High Alarm 1 value Scaled Range Minimum to R/max ?

4 848 Logical Alarm 1 AND 2, Direct Low Alarm 1 value 2,?.* scaled Range Maximum R/min PSU PCB 3. CONFIGURATION MODE ?84) Logical Alarm 1 AND 2, Reverse To access module A, first detach the PSU and CPU boards from the front by lifting ?%48 Limit Annunciator, Direct Deviation Alarm 1 Value 8?,.* Span from SP in display units 6. First select Configuration mode from Select mode (refer to section 2). first the upper, and then lower mounting struts. Gently separate the boards. Press to scroll through the parameters, then press or to set the ?%4) Limit Annunciator, Reverse Band Alarm 1 value >?,.* 1 LSD to span from setpoint 6. a. Plug the required option modules into the correct connectors, as shown below. required value. Press to accept the change, otherwise parameter will revert to Alarm 1 Hysteresis ?:A. 1 LSD to full span in display units.

5 -#+ Retransmit Limit SP Output b. Locate the module tongues in the corresponding slot on the opposite board. previous value. To exit from Configuration mode, hold down and press , to )-#2. )-#2 Retransmit PV Output High Alarm 2 value 2@?0 Scaled Range Minimum to R/max c. Hold the main boards together while relocating back on the mounting struts. return to Select mode. Low Alarm 2 value 2,?0* scaled Range Maximum R/min d. Replace the instrument by aligning the CPU and PSU boards with their guides Note: Parameters displayed depends on how instrument has been configured. /46* 0 to 5 V DC output 1. in the housing, then slowly push the instrument back into position. Refer to user guide (available from your supplier) for further details. 0 to 10 V DC output Deviation Alarm 2 Value 8?,0* Span from SP in display units 6.

6 Note: Option modules are automatically detected at power up. Parameters marked * are repeated in Setup Mode. Linear Output 2. Range #A20 2 to 10 V DC output * Band Alarm 2 value >?,0* 1 LSD to span from setpoint 6. Option Module Connectors Parameter Lower Upper Adjustment range & Description Default /40/ 0 to 20 mA DC output Alarm 2 Hysteresis ?:A0 1 LSD to full span in display units . Display Display Value 540/ 4 to 20 mA DC output Setup Lock Code +,"I* 0 to 9999 ./. Option Slot 1 Option Slot A Input (Fixed Limit 1%2#* See following table for possible codes 3$ Retransmit -1999 to 9999 Note: Operator mode screens follow, without exiting from Setup mode. Connectors Range/Type Relay) PL5 & PL6. Output 2 Scale )"0: (display value at which output Range max Code Input Type & Code Input Type & Code Input Type & maximum will be maximum) CAUTION: An excessively large filter time could significantly delay Range Range Range Retransmit -1999 to 9999 detection of a limit condition.

7 Set this value to the minimum required to remove noise from the process variable Option Slot 2. Option Slot 3 bC B: 100 - 1824 C L: - C PtRh20% vs 40%: Output 3 Scale )"0, (display value at which output Range min Connector P24F 32 - 3362 F minimum will be minimum). PL4A Connector bF B: 211 - 3315 F L: - F. PL4B Output 3 Usage C+=9 As for output 2 ?B48* 5. product INFORMATION MODE. CC C: 0 - 2320 C NC N: 0 - 1399 C PTC Pt100: 199 - 800 C Linear Output 3. C: 32 - 4208 F N: 32 - 2551 F Range #A29 As for output 2 * First select product information mode from Select mode (refer to section 2). CF NF PtF Pt100: 328 - 1472 F. Retransmit -1999 to 9999 Press to view each parameter. To exit from product Information mode, JC J: 200 - 1200 C rC R: 0 - 1759 C Pt100: - C hold down and press to return to Select mode. Panel-Mounting Output 3 Scale )"9: (display value at which output Range max The mounting panel must be rigid, and may be up to JF J: 328 - 2192 F rF R: 32 - 3198 F Pt100: - F maximum will be maximum) Note: These parameters are all read only.

8 ( ) thick 45 x 45mm J: - C S: 0 - 1762 C /40/ 0 - 20 mA DC Retransmit -1999 to 9999. (+ / SC Parameter Lower Upper Description For n multiple instruments mounted side-by-side, cut-out is Output 3 Scale )"9, (display value at which output Range min Display Display 48n-4mm ) J: - F SF S: 32 - 3204 F 540/ 4 - 20 mA DC minimum will be minimum). /46/ 0 - 50 mV DC. Input type E%4. C%1* universal input KC K: 240 - 1373 C tC T: 240 - 400 C =%?> PV is visible in Operator mode Slide mounting clamp Display Strategy 81D( =%?> Option 1 type (fixed) '2%. ),J* Latching Limit Relay KF K: 400 - 2503 F tF T: 400 - 752 F ./.6/ 10 - 50 mV DC 81+? PV not visible in Operator mode over the instrument %"%= No option fitted Mounting Panel housing towards rear face K: - C T: - C /46* 0 - 5 V DC ?+$E ASCII. of mounting panel until Serial Mm>% Modbus with no parity ),J* Relay output K: - F T: - F.

9 46* 1 - 5 V DC Communications 2)"# Mm>%* Option 2 module type Instrument the tongues engage in Mm>= Modbus with Even Parity fitted '2%0 ++)* SSR drive output LC L: 0 - 762 C PtRh20% vs. 40%: 0 - 10 V DC Protocol Housing ratchets and instrument is #)1* Triac output P24C 0 - 1850 C Mm>" Modbus with Odd Parity clamped in position. LF L: 32 - 1403 F 2 - 10 V DC..0* kbps ,1%* Linear DC voltage / current output Ratchets Note: Decimal point shown in table indicates temperature resolution of . Serial * kbps %"%= No option fitted Hold instrument firmly in Parameter Lower Upper Adjustment range & Description Default Communications Gasket Display Display Value >?78 * kbps * ),J* Relay output position (apply pressure Bit Rate Option 3 module type to bezel only) Scale Range Scale Range Lower Limit +100 Range max * kbps fitted '2%9 ++)* SSR drive output Upper Limit )7,* to Range Maximum (Lin=1000).

10 * kbps ,1%* Linear DC voltage / current output Scale Range Range Minimum to Range min CAUTION: Do not remove the panel gasket; it is a seal against dust and ),,* Comms Address ?88) *1 to 255 (Modbus), 1 to 99 (ASCII) .* 8I05 24 VDC Transmitter power supply moisture. Lower Limit Scale Range Upper Limit -100 (Linear=0). )4Ww Read/Write %"%- No option fitted Decimal point /=XXXX, .= , 0= , 9= Comms Write $"=% )4Ww* Auxiliary Option A. position 82"+* . )4/* Read only '2%? )5F6 RS485 communications Rear Terminal Wiring (non-temperature ranges only) module type fitted Process Variable Span of controller Configuration 81!1 Digital Input for remote reset USE COPPER CONDUCTORS (EXCEPT FOR T/C INPUT). '&&+* / Lock Code $,"I 0 to 9999 0/*. Single Strand wire gauge: Max (18 SWG) Offset (see CAUTION note at end of section) Firmware type &KL* Value displayed is firmware type number High Limit.