CTS/TITAN Injection Bore System - Con-Tech Systems

1 CTS/TITAN Injection Bore System Tie Back Anchors Soil Nails &. Micropiles G IBO : Injection BOring G Dynamic pressure grouted, casing free single step installation G Suits all ground conditions G Rapid, effective ground and structural stabilisation November 2006. Con-Tech Systems LTD HQ: 8150 RIVER ROAD DELTA BC, V4G 1B5 CANADA PH: (604) 946-5571 FAX: (604) 946-5548. WESTERN DIVISION: DELTA, BC, PH: (604) 946-5571, FAX: (604) 946-5548 DESCANSO CA, USA, PH: (619) 659-9931. FAX: (619)659-9932, E-MAIL: EASTERN DIVISION: ELIZABETHTOWN ON CANADA PH: (613) 342-0041, FAX: (613) 342-0609 RICHEY FL, USA, PH: (866) 848 6800 CHARLOTTE NC, USA, (704) 494-3989 E-MAIL: Con-Tech Systems LTD. HQ & WESTERN DIVISION (604) 946-5571. EASTERN DIVISION (613) 342-0041. Email: Website: CTS. Parts-List Index 1 Technical Data 3.

2 2 Drill Bit Selection Chart 5. 3 R32/20 7. 4 TITAN 30/11, TITAN 30/14 & TITAN 30/16 9. 5 TITAN 40/16 & TITAN40/20 13. 6 TITAN 52/26 17. 7 TITAN 73/56, TITAN 73/53. TITAN 73/45 & TITAN 73/35 19. 8 TITAN 103/78 & TITAN103/51 21. 9 TITAN 130/60 23. Disclaimer: All products are subject to change at any time without notice. Con-Tech Systems will make the best effort to keep you informed about any changes. Please check our website ( ) for updates. All photos are for illustrative purpose only; weights are approximate. Products must be used in conformity with safe practices and applicable codes. For best performance results, refere to CTS/TITAN /IBO installation procedures 2. CTS. Rod Size Area Load Capacity Outside Diameter Weight Note: 1 2 Subject to D / INNER Ultimate Yield Max.

3 Test Design Design Effective Nominal Temp. Anch. 60% d D change without notice. mm in2 kips kips kips kips kips in in 2. mm kN kN kN kN kN mm mm kg/m Shear Force 30/16 Allowable shear THREAD 382 220 180 176 154 132 26 30 force is deter- 30/14 mined by the THREAD 395 260 220 182 156 26 30 32/20 formula: THREAD 389 291 244 233 204 175 28 32 Yield *A. 30/11 58 Qallow =. * 3. THREAD 446 320 260 256 224 192 26 30 40/20 A: (Steel) Area THREAD 726 539 430 425 377 323 36 40 40/16 THREAD 879 660 525 520 462 396 36 40 52/26 THREAD 1337 929 730 712 650 557 49 52 73/56 Certified to THREAD 1414 1194 785 775 770 716 70 73 ISO 9001. 73/53 Con-Tech Systems LTD. THREAD 1631 1160 970 928 812 696 70 73 CTS/TITAN Technical Data EASTERN DIVISION (613) 342-0041. 73/45 HQ & WESTERN DIVISION (604) 946-5571.

4 THREAD 2260 1630 1180 1170 1141 978 70 73 73/35 THREAD 2710 1980 1355 1345 1340 1188 70 73 103/78 THREAD 3146 2282 1800 1780 1597 1369 100 103 Email: Website: 103/51 THREAD 5501 3460 2750 2740 2422 2076 100 103 TITAN 127/111: 127/111* Allowable ben- THREAD 3000 2400 1810 1800 1680 1440 100 103 ding moment =. 130/60 THREAD 9540 7940 5250 5220 5200 4764 125 130 kNm 1 2. November 2006. Temporary Anchors ; Permanent Anchors Imperial values converted from metric values; October 2006 ( lbsft). 3. Con-Tech Systems LTD. HQ & WESTERN DIVISION (604) 946-5571. EASTERN DIVISION (613) 342-0041. Email: Website: CTS/TITAN Technical Data CTS. NOTES: THE TITAN THREAD MEETS AND EXCEEDS ASTM REQUIREMENTS. FOR RE-BAR DEFORMATIONS (ASTM-A-615). GROUT CRACK. WIDTH = AT OF DESIGN LOAD. NO ADDITIONAL CORROSION PROTECTION IS REQUIRED.

5 IBO/TITAN BARS ARE ROLLED OUT OF HIGH QUALITY STEEL TUB- ING FOR SOIL NAILS, ROCK AND SOIL ANCHORS AND MINI /. MICRO PILES. THEIR UNIQUE INSTALLATION METHOD, DYNAMIC (TREMI)- GROUTING DURING DRILLING ASSURES CONTINUOUS GROUT. COVER FOR GOOD CORROSION PROTECTION AND SUPERIOR. SKIN FRICTION AND BOND. FOR ADDITIONAL CORROSION PROTECTION, BARS AND HARD- WARE CAN ALSO BE. EPOXY COATED, acc. to ASTM A-934, ASTM A-775 or AASHTO M284. ZINC METALLIZED, acc. to ASTM A-153 or AASHTO M232. HOT DIP GALVANIZED, acc. to ASTM A-153 or AASHTO M232. OR BE SUPPLIED IN (INOX) STAINLESS STEEL. INSTEAD OF EXTRA CORROSION PROTECTION, THE SACRIFICIAL- STEEL METHOD, CHOOSING THE BAR LARGER THAN. REQUIRED, CAN BE USED. THIS METHOD IS VERY COMMON IN. EUROPE AND FOR REINFORCED EARTH Systems . STOCKED TITAN BARS: 30/16, R32/20, 30/11, 30/14, 40/20, 40/16, 52/26, 73/53, 103/78, 103/51.

6 November 2006. 4. TITAN 30/11(left) TITAN 40/16 (left). for weathered soft rock Button Type Button Type and gravel hardness HV 700 hardness HV 700. hardness < 70 MPa 42 mm / 46 mm / 51 mm / 55 mm 70 mm . for hard rock, Carbide Offset Cross Cut Carbide Offset Cross Cut CTS. granite, dolomite, standstone, hardness HV 1800 hardness HV 1800. hardness 70 - 150 MPa 46 mm 70 mm . changes. Weights are approximate. Micro Piles DIN 4128 / Soil Nails / Anchors DIN 4125. TITAN TITAN TITAN TITAN TITAN TITAN. 30/11(left) 40/16 (left) 52/26 73/53 (right) 103/78 (right) 103/51 (right). for mixed soil Cross Cut Cross Cut Cross Cut Cross Cut Cross Cut Cross Cut with obstacles Drill Bit Drill Bit Drill Bit Drill Bit Drill Bit Drill Bit > 50 hardness HV 375 hardness HV 375 hardness HV 375 hardness HV 375 hardness HV 375 hardness HV 375.

7 90 mm 90 mm 115 mm 130 mm 175 mm 175 mm . 115 mm 130 mm 175 mm . for clay, soft soil Clay Bit Clay Bit Clay Bit Clay Bit Clay Bit Clay Bit and sand/gravel hardness HV 270 hardness HV 270 hardness HV 270 hardness HV 270 hardness HV 270 hardness HV 270. < 50 75 mm 110 mm 130 mm 200 mm 280 mm 280 mm . 95 mm 150 mm . for hard or high quarzite rock, Button Type Button Type Button Type Button Type Button Type reinforced concrete B25 at the carbide tipped carbide tipped carbide tipped carbide tipped carbide tipped beginning hardness HV 1800 hardness HV1800 hardness HV 1800 hardness HV 1800 hardness HV 1800. > 70 MPa 90 mm 115 mm 130 mm 175 mm 175 mm . Con-Tech Systems LTD. Drill Bit Selection Chart EASTERN DIVISION (613) 342-0041. for directional stability of Carbide Cross Carbide Cross HQ & WESTERN DIVISION (604) 946-5571.

8 + 2 % of the total length Cut 3-step Cut 3-step carbide tipped carbide tipped hardness HV 1800 hardness HV 1800. (75 mm ) 90 mm . explanation to different - Hardness to Mohs 10, carbide 9,5, correspond to HV 1800 (Hardness to Vickers),quarzite 7, slate 2,5. Email: Website: declarations of hardness - HRC 60 (Hardness to Rockwell C) correspond to HV 700 (Hardness to Vickers), HRC 38 correspond to HV 375. and rock hardness: - 70 MPa (soft soil and loose sand/gravel). - 70 150 MPa (for hard rock, like dolomit, granite, sandstone). AV8/B1-6 - value (Standard Penetration Test). Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical November 2006. 5. Con-Tech Systems LTD. HQ & WESTERN DIVISION (604) 946-5571.

9 EASTERN DIVISION (613) 342-0041. Email: Website: CTS/TITAN . CTS. Page left blank intentionally November 2006. Photos are illustrative only. Products must be used in conformity with safe practices and applicable codes and regulations. Subject to technical 6 changes. Weights are approximate. Con-Tech Systems LTD. HQ & WESTERN DIVISION (604) 946-5571. CTS EASTERN DIVISION (613) 342-0041. Email: Website: CTS/TITAN R32/20. CTS Injection Bore Hollow Bar System R32/20. TITAN Injection Hollow Bar, 32/20 mm, design load (60% GUTS) 175 kN, left hand threaded in lengths of 3 m black R32-0127 kg/m pc Accessories Spherical Collar Nut black, R32-0126 kg pc. stock Coupling black, R32-0124 kg pc. stock CTS Drill Bit - Carbide 2 , (51mm ), carbide tipped, R32-0117 kg pc. stock CTS Drill Bit - Carbide , ( ), carbide tipped, R32-0119 kg pc.

10 Stock TITAN Drill Bit - Soil Bit Y-Cut 3 , (76 mm ), R32-0115 kg pc. stock TITAN Drill Bit - Clay bit 75 mm for soft soil and loose sand/gravel, induction hardened R32-0116 kg pc. stock Flushing Head 32/20 available for R 32* (1 -1/4"), R 38* (1 -1/2"), T 38*, T 45*, for left hand rotary/percussion drilling, for flushing with water, grout or air, thread Rd 32 x 1/8" (BSP 3/4 ) male for grout hose, with lubrication nipple, to be used in connection with holder only, incl. transport box, length 265 mm, P32-001/.002/R32-0113/P32-003 kg pc. st. T38. complete set of spare seals for R 32 - T 45 flushing heads (2 seals 63 x 78 x mm plus 2 guide rings 63 x 68 x mm). T30-0369 set stock Holder, spring action, for Flushing Heads for R 32*, R 38*, T 38*, T 45*, to be fixed on to the mast of the drill rig, fixing position: hammer fully extended and spring released T30-0370 kg pc.