Cycoloy* Resin CX7240 Americas: COMMERCIAL

1 Cycoloy* Resin CX7240 Americas: COMMERCIAL Cycoloy* CX7240 Resin is an injection moldable PC/ABS blend. It contains non-brominated and non-chlorinated flame retardant systemsto meet UL-94 V0 at , V1 at , V2 at and 5VB at respectively. Excellent flow and impact balance togetherwith the thin wall flame resistance and all color options make Cycoloy CX7240 an ideal candidate for a wide variety of thin wallapplications. Property TYPICAL PROPERTIES (1)MECHANICALV alueUnitStandardTensile Stress, yld, Type I, 50 mm/min65 MPaASTM D 638 Tensile Stress, brk, Type I, 50 mm/min58 MPaASTM D 638 Tensile Strain, yld, Type I, 50 D 638 Tensile Strain, brk, Type I, 50 mm/min100%ASTM D 638 Tensile Modulus, 5 mm/min2600 MPaASTM D 638 Flexural Stress, yld, mm/min, 50 mm span104 MPaASTM D 790 Flexural Modulus, mm/min, 50 mm span2500 MPaASTM D 790 Tensile Stress, yield, 50 mm/min65 MPaISO 527 Tensile Stress, break, 50 mm/min50 MPaISO 527 Tensile Strain, yield, 50 mm/min4%ISO 527 Tensile Strain, break, 50 mm/min90%ISO 527 Tensile Modulus, 1 mm/min2600 MPaISO 527 Flexural Stress, yield.

2 2 mm/min96 MPaISO 178 Flexural Modulus, 2 mm/min2500 MPaISO 178 IMPACTV alueUnitStandardIzod Impact, notched, 23 C700J/mASTM D 256 Izod Impact, notched, -30 C175J/mASTM D 256 Instrumented Impact Total Energy, 23 C65 JASTM D 3763 Izod Impact, notched 80*10*3 +23 C20kJ/m ISO 180/1 AIzod Impact, notched 80*10*3 -30 C10kJ/m ISO 180/1 ACharpy 23 C, V-notch Edgew 80*10*3 sp=62mm20kJ/m ISO 179/1eACharpy -30 C, V-notch Edgew 80*10*3 sp=62mm10kJ/m ISO 179/1eATHERMALV alueUnitStandardVicat Softening Temp, Rate B/50110 CASTM D 1525 HDT, MPa, mm, unannealed100 CASTM D 648 HDT, MPa, , unannealed89 CASTM D 648 HDT, MPa, mm, unannealed99 CASTM D 648 CTE, -40 C to 40 C, CASTM E 831 CTE, -40 C to 40 C, CASTM E 831 Thermal CISO 8302 CTE, -40 C to 40 C, CISO 11359-2 CTE, -40 C to 40 C, CISO 11359-2 Ball Pressure Test, 75 C +/- 2 CPass-IEC 60695-10-2 Vicat Softening Temp, Rate B/50110 CISO 306 Vicat Softening Temp, Rate B/120113 CISO 306 HDT/Af, MPa Flatw 80*10*4 sp=64mm93 CISO 75/AfRelative Temp Index, Elec90 CUL 746 BRelative Temp Index, Mech w/impact90 CUL 746 BRelative Temp Index, Mech w/o impact90 CUL 746 BPHYSICALV alueUnitStandardSpecific D 792 Mold Shrinkage, flow, - MethodMelt Flow Rate, 260 kgf18g/10 minASTM D ISO 1183 Water Absorption.

3 (23 C/sat) 62 Moisture Absorption (23 C / 50% RH) 62 Melt Volume Rate, MVR at 260 kg15cm /10 minISO 1133 ELECTRICALV alueUnitStandardHot Wire Ignition {PLC)3 PLC CodeUL 746 AHigh Ampere Arc Ign, surface {PLC}0 PLC CodeUL 746 AComparative Tracking Index (UL) {PLC}3 PLC CodeUL 746 AVolume Resistivity> +15 Ohm-cmIEC 60093 Surface Resistivity, ROA> +15 OhmIEC 60093 Dielectric Strength, in oil, mm35kV/mmIEC 60243-1 Dielectric Strength, in oil, mm25kV/mmIEC 60243-1 Dielectric Strength, in oil, mm17kV/mmIEC 60243-1 FLAME CHARACTERISTICSV alueUnitStandardUL Recognized, 94V-1 Flame Class Rating (3) 94UL Recognized, 94V-0 Flame Class Rating (3) 94UL Recognized, 94-5VA Rating (3)3mmUL 94UL Recognized, 94-5VB Rating (3) 94 Glow Wire Flammability Index 960 C, passes 60695-2-12 Glow Wire Ignitability Temperature, mm825 CIEC 60695-2-13 Glow Wire Ignitability Temperature, mm800 CIEC 60695-2-13 Source GMD, last updated:02/14/2005 ProcessingParameterInjection MoldingValueUnitDrying Temperature80 - 90 CDrying Time2 - 4hrsMaximum Moisture Temperature250 - 300 CNozzle Temperature250 - 300 CFront - Zone 3 Temperature250 - 300 CMiddle - Zone 2 Temperature240 - 290 CRear - Zone 1 Temperature230 - 280 CHopper Temperature60 - 80 CMold Temperature60 - 85 CSource GMD, last updated.}

4 02/14/2005 THESE PROPERTY VALUES ARE NOT INTENDED FOR SPECIFICATION PURPOSES. PLEASE CHECK WITH YOUR (LOCAL SALES OFFICE) FOR AVAILABILITY IN YOUR REGION(1) Typical values only. Variations within normal tolerances are possible for various colors. All values are measured after at least 48 hoursstorage at 23 C/50% relative humidity. All properties, except the melt volume and melt flow rates, are measured on injection moldedsamples. All samples tested under ISO test standards are prepared according to ISO 294.(2) Only typical data for selection purposes. Not to be used for part or tool design.(3) This rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.

5 (4) Internal measurements according to UL : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE SABIC INNOVATIVEPLASTICS COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("SABIC IP"), ARE SOLD SUBJECT TO SABIC IP' SSTANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHERSALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, ANDAVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINEDHEREIN IS GIVEN IN GOOD FAITH, SABIC IP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED,(I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (II) AS TOTHE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SABIC IP MATERIALS, PRODUCTS,RECOMMENDATIONS OR ADVICE.

6 EXCEPT AS PROVIDED IN SABIC IP' S STANDARD CONDITIONS OF SALE,SABIC IP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTINGFROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN. Each user bears full responsibility for making itsown determination as to the suitability of SABIC IP' s materials, products, recommendations, or advice for its own particular use. Eachuser must identify and perform all tests and analyses necessary to assure that its finished parts incorporating SABIC IP materials orproducts will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendationor advice, shall be deemed to alter, vary, supersede, or waive any provision of SABIC IP' s Standard Conditions of Sale or this Disclaimer,unless any such modification is specifically agreed to in a writing signed by SABIC IP.

7 No statement contained herein concerning apossible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent orother intellectual property right of SABIC Innovative Plastics Company or any of its subsidiaries or affiliates covering such use or design,or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right* Cycoloy is a trademark of the SABIC Innovative Plastics Company 1997-2008 SABIC Innovative Plastics rights reserv