Datasheet for Contractors SCS1001 Clear, …

1 Contractors SCS1001 Contractors SCS1000 silicone SealantProduct DescriptionContractors SCS1000 series silicone adhesive sealants areone part sealants that offer excellent adhesion, weatherabilityand elasticity for general glazing and sealing SCS1000 sealant is available in 4 colors plustranslucent:Product DesignationColor SCS 1001 TranslucentSCS1002 WhiteSCS1003 BlackSCS1009 AluminumSCS1097 BronzeKey PerformancePropertiesBASIC USESG eneral Glazing: Glass, plastic, channel or Sealing: Glass, metal, granite and Sealing: Sheet metal, skylights, ventilators, air conditioning,metal/plastic signs, glass block structures, bedding of For: Structural GlazingNot For: Bathrooms Use SCS1700 Series SealantNot For: Concrete, Marble, Limestone, Lead, Zinc, or Below WaterContractors SCS1000 series silicone sealant should not be appliedto reflecting, high gloss, or light colored surfaces where aestheticsare critical, until adequate on site sealant , surface and ambientatmospheric tests simulating building design are conducted toascertain material compatibility and migration to adjacent surfacesunder actual use SCS1000 silicone sealant is not recommended formirror installations without the approval ofthe mirror Product DataPropertiesValueHardness (Shore A)28 Ultimate Tensile Strength(At Maximum Elongation)290 psiDynamic Movement andCapability 25%Tack Free Time30 Time5 to 7 days ' sectionat 23 C (75 F)

2 Sag or DATAC ontractors SCS1000 silicone sealants exhibit typical siliconesealant resistance to the environments encountered in generalpurpose glazing and sealing applications. These environmentsinclude ultraviolet radiation, ozone, high and low temperatureextremes and hydrolytic stability (high temperature and humidity).TECHNICAL SERVICESC omplete technical information and literature is available from GESilicones Technical Centers. Laboratory facilities and applicationengineering are available upon request from GE Silicones. Anytechnical advice furnished by the Company, or any representative ofthe Company, concerning any use or application of any sealant isbelieved to be reliable but the Company makes no warranty, expressor implied, of any use or application for which such advice product data values should not be used asspecifications.

3 Assistance and specifications are available bycontacting GE Silicones at 800/255 STANDARDSC ontact GE Quality Assurance for details on certifications to:Federal Specifications TT S 001543A ASTM C920 Type S, NS, Class 25, USE NT G, A & O. TT S STATUSGE has on file documentation from USDA which states thatContractors SCS1001 , SCS1002, SCS1003 and SCS1009sealants are chemically acceptable for use on structuralsurfaces in official establishments operating under the FederalMeat and Poultry Inspection Program. Contractors SCS1097does not have USDA approval. For further information,2contact GE Silicones Product Regulatory final granting of authorization for the proposed use ofsuch compounds is the responsibility of the inspector incharge of the official plant.

4 Technical assistance will beprovided by the Product Safety Branch of USDA STATUSThe following sealants may be used in food contactapplications for repeated use under FDA Regulation 21 Adhesives and Resinous and PolymericCoatings : SCS1001 , SCS1002, SCS1003, SCS1009 use of these adhesive sealants is subject to the followingconditions:The adhesive sealant is applied in accordance with GoodManufacturing Practice at a thickness not to exceed 6 mm( in.) from an exposed edge. As a continuous film between joints acting as a functionalbarrier between the food and the substrate (areaunderneath the joint). The adhesive sealant must be cured for a minimum of 14days at 25 C (77 F) and 50% The operating temperature of the adhesive sealant aftercure must not exceed 177 C (350 F).

5 All previously mentioned adhesive sealants must be evaluated todetermine bond strength for each specific application. If greateradhesion is required, the evaluation of SS4044 ( clear ) primer isrecommended. SS4044 primer may be used in repeated contact withfood under 21 CFR , Resinous and Polymeric Coatings .SS4179 does comply with FDA STATUSNSF International lists SCS1001 , SCS1002, SCS1003 andSCS1009 adhesive sealants under NSF International Standard 51 Plastic Materials and Components for Use in FoodEquipment as satisfactory for use on splash zone for UseLINEAR FEET PER GALLON OF GE CONTRACTORSSCS1000 SERIES silicone sealant FOR VARIOUSJOINT SIZESWIDTH, INCHES1/31/43/81/25/83/411/8123261641130 72462051543/16 41127520516413710331/4 307205154123103773/8 137103826851 JOINT DESIGN AND DIMENSIONSS ilicone sealants should be no thicker than 3/8' and no thinner than1/8'.

6 The use of a bond breaker prevents three sided or polyurethane foam rods are recommended asback up materials. If the joint is too shallow to allow foam rod, use abond breaker width of building expansion joints varies because of seasonaland daily changes in temperature. The designed joint width must beat least four times the expected thermal PREPARATION: sealant bonding surfaces should besound, clean, dry and free of contamination. Use isopropyl alcoholwipe to clean : On glass and glazed surfaces, primers are not primer may be required on plastics and other constructionmaterials for maximum adhesion. It is recommended that a bead ofsealant be applied to the substrate material to test adhesion prior togeneral job : Areas adjacent to joints should be masked, preferablybefore priming, it if is necessary to obtain a neat sealant OF APPLICATIONC ontractors SCS1000 sealant can be applied directly from plasticcaulking cartridges with a hand gun or pressure SCS1000 silicone sealant is supplied as aready to use, one part sealant with a lightweight consistency.

7 Thisconsistency remains relatively unchanged over a temperature rangeof 35oF to 140oF ( 37oC to 60oC), allowing the sealant to be easilygunned in any season, to clean, dry, frost free surfaces. WhileContractors SCS1000 is gunnable at temperatures as low as 35oF,the cure rate will be very slow below 40oF. Additionally, the sealantmay not cure to its design properties if cured at temperatures N SCS1800 sealant is available in , 5 gallon pails, and 55 gallon drums. Pricing ofpails and drums is based on weight of material contained. Handling and SafetyMaterial Safety Data Sheets are available upon request from GE Silicones. Similar information for solvents andother chemicals used with GE products should be obtained from your suppliers. When solvents are used, propersafety precautions must be recommended pressure for air operated guns with caulking cartridges is 45 psi ( kgs/cm2).

8 Storage and WarrantyPeriodThe warranty period is 24 months from date of shipment from GE Silicones if stored in the original unopened container at27 C (80 F).AvailabilityContractors SCS1000 series silicone adhesive sealants may be ordered from GE Silicones, Waterford, New York12188, the Sales Office nearest you or from an authorized GE silicone product distributor. For availability and4cost information, consult your nearest GE Silicones sales office at 1 800 255 to considering use of a GE Silicones' product in fulfilling any government requirement, pleasecontact the Government and Trade Compliance office at 413 4348 DISCLAIMERTHE MATERIALS, PRODUCTS AND SERVICES OF GE SILICONES, GE BAYER SILICONES, GE TOSHIBA SILICONES,THEIR SUBSIDIARIES OR AFFILIATES (THE SUPPLIER ), ARE SOLD SUBJECT TO THE SUPPLIER S STANDARDCONDITIONS OF SALE, WHICH ARE INCLUDED IN APPLICABLE SALES AGREEMENTS, PRINTED ON THE BACK OFACKNOWLEDGMENTS AND INVOICES, OR AVAILABLE UPON REQUEST.

9 ALTHOUGH THE INFORMATION,RECOMMENDATIONS OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SUPPLIER MAKES NO WARRANTYOR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDEREND USE CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATINGSUPPLIER S MATERIALS, PRODUCTS, SERVICES, RECOMMENDATIONS OR ADVICE. NOTHING IN THIS OR ANYOTHER DOCUMENT SHALL ALTER, VARY, SUPERSEDE OR OPERATE AS A WAIVER OF ANY OF THE SUPPLIER SSTANDARD CONDITIONS OF user bears the full responsibility for making its own determination as to the suitability of Supplier s materials, products,services, recommendations or advice for its own particular purpose. Each user must identify and perform tests and analysessufficient to assure it that its finished parts will be safe and suitable for use under end use conditions.

10 Because actual use ofproducts by the user is beyond the control of Supplier, such use is within the exclusive responsibility of the user, and Suppliercannot be held responsible for any loss incurred through incorrect or faulty use of the products. Further, no statement containedherein concerning a possible or suggested use of any material, product, service or design is intended or should be construed togrant any license under any patent or other intellectual property right of Supplier or any of its subsidiaries or affiliatedcompanies, or as a recommendation for the use of such material, product, service or design in the infringement of any patent orother intellectual property