DESCRIPTION Type Date - cooperindustries.com

1 TD518010EN11/13/2018 SPECIFICATION FEATURESDESCRIPTIONThe Halo Surface LED Downlight (SLD) incorporates WaveStream technology to create an ultra-low profile surface mounting luminaire with the performance and look of a traditional downlight. SLD6 is designed for installation in many 3-1/2 and 4 square, octagon or round junction boxes. And may also retrofit in 5 and 6 IC and Non-IC recessed housings.* Suitable for residential or commercial installations. Ideal for closets, storage areas, attics and basements. Compliant with NFPA 70, NEC Section (A)(3) and (C)(5).CONSTRUCTION Die cast aluminum trim ring, and die formed aluminum frameOPTICS WaveStream technology provides uniform luminance from a low profile flat lens AccuAim optics provide directional control for the cone-of-light beam distribution of a traditional downlight. Precision molded lens features high transmission polymer with UV stabilized protecting filmDESIGNER TRIMSA ccessories (sold separately)SLD designer trims are accessory rings that attach to the SLD for a permanent finish.

2 * Refer to SLD accessories specification sheet for details. White (Paintable) Satin Nickel Tuscan Bronze*SLD accessory trims attach with permanent adhesion and are not interchangeable after JUNCTION BOX MOUNTING SLD may be used in compatible electrical junction boxes in direct contact with insulation including spray foam insulation Suitable for installation in many 3-1/2 and 4 square, octagon, and round electrical junction boxes Note: Driver consumes 3 cubic inches of junction box Installer must ensure compatibility of fit, wiring and proper mounting in the electrical junction box. This includes all applicable national and local electrical and building codes. Proprietary Slot-N-Lock quick installation system for junction box installation T-bracket with Slot-N-Lock mounting tabs includedRECESSED HOUSING MOUNTING May be installed in IC recessed housings in direct contact with insulation* Note: Not for use in recessed housings in direct contact with spray foam insulation.

3 Refer to NEMA LSD 57-2013 Torsion Spring 5 & 6 Optional precision formed torsion spring bracket kit is included The torsion springs adjust on the frame to fit 5 or 6 compatible housingsFriction Blade 5 & 6 Optional precision formed friction blades included For retrofit in 5 and 6 housings without torsion spring mounting tabs Friction blade design allows the SLD to be installed in any position within the housing aperture (360 degrees)LED Linear LED arrays are integrated in trim perimeter Color Temperature: 2700K, 3000K, 3500K, 4000K CRI options: 80 and 90 - 90 CRI can be used for California Title 24 compliance/ certified to Title 20 - 80 CRI can be used to comply with California Title 24 Non- Residential Lighting Controls as a LED provides a five year limited warranty on the SLD LEDLED CHROMATICITY A tight chromaticity specification ensures LED color uniformity, sustainable Color Rendering Index (CRI) and Correlated Color Temperature (CCT) over the useful life of the LED LED chromaticity of 3 SDCM exceeds ENERGY STAR color standards per ANSI.

4 90 CRI model features high color performance with R9 greater than 50 Every Halo LED is quality tested, measured, and serialized in a permanent record to register lumens, wattage, CRI and CCT. Halo LED serialized testing and measurement ensures color and lumen consistency on a per-unit basis, and validates long-term product consistency over timeELECTRICAL CONNECTIONSJ unction Box Compatible with 3-1/2 x 2 and 4 x 1-1/2 deep round, square and octagon boxes (2-1/8 deep boxes recommended) Supply Wire Adapter with LED quick connector includedRecessed Housings LED connector is compatible with Halo 5 H550 Series and 6 H750 Series LED Housings LED Connector meets California Title-24 high-efficacy luminaire standard as a non-screw base The included E26 Edison screw-base adapter provides capability for retrofit* LED connector is a non-screwbase luminaire disconnect for tool-less installationSLD 1200 SeriesSLD6128xxWH80 CRI2700K, 3000K, 3500K, and 4000K SLD6129xxWH90 CRI2700K, 3000K, 3500K, and 4000K6 Surface LED DownlightHigh Lumen 1200 Series Suitable for ceiling or wall electrical junction boxesSuitable for5 & 6 recessed housing retrofit(IC, Non-IC & AIR-TITE )ENERGY DATA80 CRI90 CRIL umens(4000K models)12151000 Input Voltage120V120 VFrequency50/60 Hz50/60 HzInput AInput WEfficiency(4000K models)

5 82 lm/W68 lm/WTHD 20%Power Factor Ambient-30 - +40 CSound RatingClass A2700 Knominal80 CRI2700K3500K4000K3000K80 CRI2700K3500K4000K3000K3500 Knominal80 CRI2700K3500K4000K3000K4000 Knominal80 CRI2700K3500K4000K3000K2700 Knominal90 CRI2700K3500K4000K3000K3500 Knominal90 CRI2700K3500K4000K3000K4000 Knominal90 CRI2700K3500K4000K3000 Knominal CCT90 CRI2700K3500K4000K3000 Knominal CCT2700 Knominal80 CRI2700K3500K4000K3000K80 CRI2700K3500K4000K3000K3500 Knominal80 CRI2700K3500K4000K3000K4000 Knominal80 CRI2700K3500K4000K3000K2700 Knominal90 CRI2700K3500K4000K3000K3500 Knominal90 CRI2700K3500K4000K3000K4000 Knominal90 CRI2700K3500K4000K3000 Knominal CCT90 CRI2700K3500K4000K3000 Knominal CCTNOMENCLATURESLD612830WH 612 = 6 SLD 1200 Series 8 = >80 CRI 30 = 3000K WH = Matte WhiteRefer to ENERGY STAR Certified Products to ENERGY STAR Qualified Products be used to comply with California Title 24 High Efficacy to California Appliance Efficiency Database under LED nominal CCT of 4000K or less.

6 *Non-California Product OnlyCatalog #ProjectCommentsPrepared byTypeDateHALOSLD6128xxWHSLD6129xxWHSLD 1200 SeriesSLD6128xxWH80 CRI2700K, 3000K, 3500K, and 4000K SLD6129xxWH90 CRI2700K, 3000K, 3500K, and 4000K6 Surface LED DownlightHigh Lumen 1200 Series Suitable for ceiling or wall electrical junction boxesSuitable for5 & 6 recessed housing retrofit(IC, Non-IC & AIR-TITE )LED DRIVER Driver is a 120V input, high efficiency, dimmable electronic power supply providing DC power to the LED arrays Driver features high power factor, low THD, and has integral thermal protection in the event of over temperature or internal failure Driver is replaceable if it should be requiredDIMMING Designed for continuous dimming capability to nominally 5% with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming to 5% is best assured using dimmers with low end trim adjustment. Consult dimmer manufacturer for compatibility and conditions of use.

7 (Note some dimmers require a neutral in the wallbox.)COMPLIANCE cULus Listed ceiling and wall cULus Damp Location listed ceiling and wall cULus Wet Location Listed, ceiling only (shower rated) Suitable for use in closets, compliant with NFPA 70, NEC Section (A)(3) and (C)(5) SLD may be used in compatible electrical junction boxes in direct contact with insulation including spray foam insulation May be installed in IC recessed housings in direct contact with insulation (Not for use in recessed housings in direct contact with spray foam insulation. Refer to NEMA LSD 57-2013) UL Classified when used in retrofit with listed housings (See Housing Compatibility) EMI/RFI: meets FCC 47 CFR Part 15 Class B limits, and is suitable for use in residential and commercial installations Airtight certified per ASTM E283 (not exceeding CFM under 57 Pascals pressure difference) 90 CRI: Can be used to comply with California Title 24 High Efficacy requirements.

8 Can be used for International Energy Conservation Code (IECC) and Washington State Energy Code high efficiency luminaire compliance ENERGY STAR certified luminaire - consult ENERGY STAR Certified Product List Contains no mercury or lead and RoHS compliant. Photometric testing in accordance with IES LM-79 Lumen maintenance projections in accordance with IES LM-80 and TM-21 DIMENSIONSORDERING INFORMATIONSAMPLE NUMBER: SLD612927WH SLD6 TRMSNJ unction Box Installation: Order junction box separately, as supplied by others, to complete Installation: Order Halo recessed housing separately to complete Rendering IndexColor Temperature (CCT)FinishAccessoriesSLD612= 6 Surface LED Downlight, 120V 1200 SeriesCalifornia non-E26 ModelsSLD612927WH-CASLD612930WH-CASLD612 935WH-CASLD612940WH-CA8=80 CRI9=90 CRI27=2700K30=3000K35=3500K40=4000 KWH=WhiteDesigner Trims Fit over the SLD for a designer finishSLD6 TRMSN=6 SLD Satin Nickel SLD6 TRMTBZ=6 SLD Tuscan Bronze SLD6 TRMWH=6 SLD White (paintable)*SLD accessory trims attach with permanent adhesion and are not interchangable after installationJ-Box Spacer Extension Ring Add 15/16 depth when SLD driver cannot fit into installed junction boxSLD6 EXT=6 Surface LED J-Box Extender, AdaptersWhen junction box is mounted flat on a ceiling or beam surface (not recessed in ceiling)SLD6 RAD=6 SLD Round Surface J-Box Adapter, (for 4-inch round or octagon junction boxes.)

9 SLD6 SADPLT=6 SLD Square Surface J-Box Adapter Plate (For 4-inch square junction boxes, use with SLD6 RAD.)Spare PartsSLD6 ACCKIT=6 Accessory Parts Replacement Kit (Screwbase adapter, torsion springs, friction blades)SLD6 BRKT=6 Junction Box Bracket & ScrewsRefer to SLD Accessories specification sheet for further [ ].7 [ ].8 [ ] [ ]page 2 SLD6128xxWHSLD6129xxWHHOUSING COMPATIBILITYThe SLD6 is UL Listed in Halo and All-Pro recessed housings, and is UL Classified for use with any 5 or 6 inch diameter recessed housing constructed of steel or aluminum with an internal volume that exceeds in in addition to those noted below. Note: Some other s housings require installation with included friction 3 Compatible Halo LED Housings with LED luminaire connector (high-efficacy compliant)HALOLEDR ecessed Can SizeCatalog Number5"H550 ICAT, H550 RICAT, E550 ICAT, E550 RICAT6"H750 ICAT, H750 RICAT, H750T, H750 RINTD010, H750 TCP, H2750 ICAT, H2750 RICAT, E750 ICAT, E750 RICATHalo LED Retrofit EnclosuresHALO6"ML7 BXRFK, ML7E26 RFKC ompatible Halo Incandescent E26 Screwbase HousingsHALO5"H5 ICAT, H5 RICAT, H5 ICATNB, H5T, H5RT, H25 ICAT, H25 ICATNB, E5 TAT, E5 RTAT, H5 TNB, E5 TATNB, E5 ICAT, E5 RICAT, E5 ICATNB6"H7 ICAT, H7 RICAT, H7 ICT, H7 RICT, H7 ICATNB, H7 ICTNB, H7T, H7RT, H7 TNB, H7 TCP, H7 UICT, H7 UICAT, H27 ICAT, H27 RICAT, H27T, H27RT, E7 ICAT, E7 RICAT, E27 ICAT, E27 RICAT, E7 ICATNB, E7 TAT, E7 RTAT, E7 TATNB, E27 TAT, E27 RTATSLD6128xxWHSLD6129xxWH*This is a representative list of compatible junction boxes only.

10 Information contained in this literature about other manufacturers products is from published information made available by the manufacturer and is deemed to be reliable, but has not been verified. Eaton makes no specific recommendation on product selection and there are no warranties of performance or compatibility implied. Installer must determine that site conditions are suitable to allow proper installation of the SLD mounting bracket in the " square deep steel box4" x 4" x 2-1/8"(102mm x 102mm x 54mm)COMPATIBLE WITH MANY OTHER JUNCTION BOXES*COMPATIBLE WITH EATON S CROUSE-HINDS JUNCTION BOXES4" octagon light fixture/fan steel box4" x 4" x 2-1/8"(102mm x 102mm x 54mm) TP316 - for non-metallic cable TP317 - for metal clad cable UL Listed Refer to non-metallic cable4 x 4 x 2-1/8 (102mm x 102mm x 54mm)TP317for metal clad cable4 x 4 x 2-1/8 (102mm x 102mm x 54mm)4" round new work non-metallic box with hanger bar assembly4" diameter x 2-3/16" (102mm x 56mm)3-1/2" round old work non-metallic box4-1/4" flange, 3-1/2" x 2-5/8 (108mm , 89mm x 67mm)4" round new work non-metallic light fixture/fan box4" diameter x 2-3/16"(102mm x 56mm)