Example: marketing

Dill TPMS Relearn Procedure A1202 - dillvalves.com

For more information contact dill or your nearest dill distributor. dill tpms Relearn Procedure A1202 A properly formatted tpms scan tool is required to perform this Procedure . Sensor Relearn Procedure if tpms light is off. 1. Ensure all tires are inflated to the pressure listed on the tire placard. 2. If using a Bartec tool, use the Relearn option, not Test Sensor . If using an Ateq tool, use the Service tpms menu, not Check . 3. Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR, & full size spare (if equipped). 4. Turn ignition to the ON position. 5. Connect scan tool to OBDII port and upload sensor IDs. 6. Unplug the OBDII cable, keep ignition still in the ON position. 7. To verify baseline tire pressures are correct, set the parking brake, then hold down pressure warning reset switch (see possible locations on 2nd page) until tpms indicator blinks 3 times.

Dill TPMS Relearn Procedure – A1202 A properly formatted TPMS scan tool is required to perform this procedure. Sensor Relearn Procedure if TPMS light is off. 1. Ensure all tires are inflated to the pressure listed on the tire placard. 2. If using a Bartec tool, use the “Relearn” option, not “Test Sensor”. If using an Ateq tool, use ...

Fullscreen Download

Tags:

  Procedures, Learners, Tpms, Dill, Relearn procedures, 2012a, Dill tpms relearn procedure a1202

Information

Domain:

Source:

Link to this page:

Please notify us if you found a problem with this document:

Other abuse

Transcription of Dill TPMS Relearn Procedure A1202 - dillvalves.com

1 For more information contact dill or your nearest dill distributor. dill tpms Relearn Procedure A1202 A properly formatted tpms scan tool is required to perform this Procedure . Sensor Relearn Procedure if tpms light is off. 1. Ensure all tires are inflated to the pressure listed on the tire placard. 2. If using a Bartec tool, use the Relearn option, not Test Sensor . If using an Ateq tool, use the Service tpms menu, not Check . 3. Starting with the Left Front tire, use the scan tool to scan each sensor in the following order: LF, RF, RR, LR, & full size spare (if equipped). 4. Turn ignition to the ON position. 5. Connect scan tool to OBDII port and upload sensor IDs. 6. Unplug the OBDII cable, keep ignition still in the ON position. 7. To verify baseline tire pressures are correct, set the parking brake, then hold down pressure warning reset switch (see possible locations on 2nd page) until tpms indicator blinks 3 times.

2 If vehicle is not equipped with this button, move on to Step 8. 8. With the ignition still in the ON position, re-scan each sensor. 9. Test drive the vehicle above 30mph or more for at least 10 minutes, monitor the low tire pressure monitor to ensure it does not illuminate or blink. Sensor Relearn Procedure if tpms light is on. 1. Ensure all tires are inflated to the pressure listed on the tire placard. 2. Turn ignition to the ON position. 3. When using the updated Ateq or Bartec tool, utilize the tool s Reset ECU function under one of the menus: plug into vehicle s OBD port and follow tool s onscreen prompts. If tool function is not available, move on to Step 4. 4. If using a Bartec tool, use the Relearn option, not Test Sensor . If using an Ateq tool, use the Service tpms menu, not Check . 5. Use the scan tool to scan each sensor in the following order: Left Front, Right Front, Right Rear, Left Rear, & full size spare (if equipped).

3 6. Turn ignition to the ON position. 7. Connect scan tool to OBDII port and upload sensor IDs. 8. Unplug the OBDII cable, keep ignition still in the ON position. 9. To verify baseline tire pressures are correct, set the parking brake, then hold down pressure warning reset switch (see possible locations on 2nd page) until tpms indicator blinks 3 times. If vehicle is not equipped with this button, move on to Step 10. 10. With the ignition still in the ON position, re-scan each sensor. 11. Test drive the vehicle above 30mph or more for at least 10 minutes, monitor the tpms indicator to ensure it does not illuminate or blink. Tire Pressure Reset and Tire Rotation Reset Procedure (select models) 1. Ensure all tires are inflated to the pressure listed on the tire placard. 2. Apply parking brake and turn ignition to ON position (engine OFF). 3. Hold down pressure warning reset switch (see possible locations on 2nd page) until tpms indicator blinks 3 times.

4 4. It will take several minutes for the ECU to receive signals from the sensors and complete initialization. For more information contact dill or your nearest dill distributor. Pressure Reset Button Main/2nd Switch Satellite Switch (Lexus only) Image Description Used to set the vehicle s baseline placard pressure. Once the vehicle receives a signal from the sensor after the button has been pressed, the vehicle stores that received pressure reading as the baseline for that tire position. Used to select between two previously registered sets of tpms sensor ID codes. Used to select between two previously registered sets of tpms sensor ID codes; Multiple vehicle systems use these buttons for their control. IMPORTANT Do not press this button unless the currently installed tpms sensors are registered to the vehicle AND the current tire pressures match the pressure rating listed on the vehicle s door placard.

5 If the tpms light is on due to a tpms fault, by pressing this button the vehicle may enter into an error loop that will require a tpms tool s ECU Reset function to fix the problem. When using aftermarket scan tools, verify the button is in MAIN before registering sensors. When using aftermarket scan tools, verify the system is in MAIN before registering sensors.

Show more