Dimensions - classic.hobson.com.au

Quality Fasteners Since 1935 August 2007 Dimensions OF STRUCTURAL BOLTS AS1252 - 1983 Bolt Body dia. Width across flatsWidth across cornersHeight of headDP Length - Refer Hobson Product List Refer to nut Dimensions below for washer face - DtGENERAL Dimensions OF STRUCTURAL NUTS AS1252 - 1983 Nom. Nut pitch Width across flatsWidth across cornersNut heightWasher-face or chamfer sem size across Bolts Structural NutsDimensionsesDs45okD15 - 30ooDtD15 - 30oomtes

Thread Pitch Width across flats Width across corners Nut height Washer-face or chamfer dia. D P s e m Dt max. min. max. min. max. min. max. min. M12 1.75 21.0 20.16 24.25 22.78 13.1 12.0 Actual size across flats. 19.20 M16 2.0 27.0 26.16 31.2 29.56 17.1 16.0 24.90 M20 2.5 32.0 31.00 36.9 35.03 21.3 20.0 29.50 ...

Tags:

  Pitch

Information

Documents from same domain

TIGHTENING TORQUES AND THE TORQUE-TENSION …

classic.hobson.com.au

Table 12). However, one of the least expensive tech-niques that provides a reasonable level of accuracy versus cost is by measuring torque. The fundamental characteristic required is to know the relationship between torque and tension for any particular bolted joint. Once the desired design preload must be identified

  Table, Torque

Minimum Tensile Stress - Hobson

classic.hobson.com.au

m3 0.50 5.03 225 580 - 830 m4 0.70 8.78 225 580 - 830 m5 0.80 14.20 225 580 - 830 m6 1.00 20.10 225 580 - 830 m8 1.25 36.60 225 580 - 830 m10 1.50 58.00 225 580 - 830 m12 1.75 84.30 225 580 580 830 m14 2.00 115.00 225 580 580 830 m16 2.00 157.00 225 580 580 830 m18 2.50 192.00 225 600 600 830 m20 2.50 245.00 225 600 600 830 m22 2.50 303.00 225 ...

  Minimum, Stress, Tensile, Minimum tensile stress

Related documents

BELT I.D. CHART - Gates Corporation

www.gates.com

2mm Pitch 3mm Pitch 5mm Pitch 8mm Pitch 14mm Pitch B C A POWERGRIP HTD™ BELTS Examples: 350-5M-15 Belt P28-5M-15AL Sprocket 3mm Pitch 5mm Pitch 20mm Pitch B C A POWERGRIP TIMING BELTS Examples: 210L100 Belt TL18L100 Pulley Standard Widths (in.) A B C MXL 1/8, 3/16, 2.03mm 1.14mm 0.51mm 1/4 .080 in. .045 in. .020 in.

  Pitch, Corporation, Gate, Gates corporation

V-Belts & Pulleys - PT Parts

www.ptparts.com.au

!PITCH - This is the distance from the center of one tooth to the center of the next tooth. Naismith Engineering stock 4 sizes of HTD timing pulley 3M where the pitch equals 3mm, 5M where the pitch equals 5mm, 8M where the pitch equals 8mm and 14M where the pitch equals 14mm. WIDTH - This is the width of the belt that runs on the pulley.

  Pitch

Belt Number & Identification Chart

resources.kamanmarketing.com

Aug 31, 2010 · 3mm, 5mm, 8mm & 14mm PowerGrip HTD (Fiberglass) — 14mm PowerGrip HTD (Steel) MXL, XL, L and H pitch PowerGrip Timing (Fiberglass) — XL, L and H pitch PowerGrip Timing (Steel) Available in 8mm and 14mm —˚Poly Chain ¤ GT 2

  Pitch, Belt

Optibelt Power Transmission product range belts

www.optibelt.com

= pitch length L w SPZ/3V, SPB/5V = replaceable sizes (not to be combined in sets) Ordering example: SPZ 487 Please make sure to mention the product name in your order. optibelt SK S=C PLUS Profiles: SPZ, SPA, SPB, SPC Profiles: 3V, 5V, 8V BACK TO THE TABLE OF CONTENTS

  Pitch

Related search queries