Dimensions - Rock Crusher

1 Dimensions TC-20 The TC-20 tracked Crusher has the largest hopper in its class and is built for big loads and even bigger production. IROCK s TC-20 produces a uniform, cubical product that will increase your bottom line. Features A 15-cubic-yard fixed Hardox hopper is paired with a 52-inch by 16-foot vibrating grizzly feeder with a larger Crusher inlet for increase production rates. The TC-20 s feeder is the longest among tracked crushers and allows operators to feed material with a large wheel loader. A 48-inch-wide discharge conveyor can stockpile up to a maximum height of 10-feet, 11-inches. Operators can hydraulically lower or raise the conveyor to feed stockpiling conveyors and make maintenance easier. The standard ROCK BOX reduces wear on the discharge point by forming crushed material into a natural rock shelf to serve as a liner. A standard wireless remote control offers standard full plant functions and two-speed tracking for easy maneuverability around a job site or onto a trailer.

2 Specifications GENERAL MODEL TC-20 SHIPPING Dimensions LENGTH 57' 8-15/16" WIDTH 11' 8-7/16" HEIGHT 12' 4-13/16" WEIGHT 98,500 lbs OPERATING Dimensions LENGTH 57' 7" WIDTH 17' 3" HEIGHT 12' 7" POWER ENGINE CAT C-13 ACERT DIESEL , "C" INTERMITTENT DUTY, (Tier 3) EMISSIONS APPROVED ENGINE HP 440 HP CLUTCH HPTO 12 HYDRAULICALLY APPLIED DRY CLUTCH FUEL TANK CAPACITY 140 GALLONS HYDRAULICS - PLANT SYSTEM #1 SYSTEM #1 OPERATES THE FEEDER, RIGHT TRACK, LEFT TRACK, MAIN CONVEYOR, SIDE CONVEYOR, MAGNET BELT, AND Crusher DOOR. SYSTEM #1 IS DRIVEN OFF TWO PUMPS MOUNTED ON THE CAT C13 SAE No 1 FLYWHEEL HOUSING. DUEL REAR PTO OPERATES AT TIMES ENGINE SPEED WITH SAE "C" 14T 12/24 DP SPLINE SHAFT INPUT. SYSTEM #2 SYSTEM #2 SUPPLIES HYDRAULIC POWER TO THE CLUTCH, GALTECH VALVE, AND THE COOLING RADIATOR. THE GALTECH VALVE OPERATES THE OPTIONAL MAIN CONVEYOR FOLD, SIDE CONVEYOR FOLD, UPPER APRON ADJUST, LOWER APRON ADJUST AND ALSO CONTAINS A CHECK VALVE FOR HEATING THE OIL WHEN IT IS BELOW THE SETPOINT.

3 PUMP DRIVE ROTATES SAME DIRECTION AS CRANKSHAFT AT TIMES ENGINE SPEED WITH SAE"B" 13T 16/32 DP SPLINE SHAFT INPUT. HYDRAULIC TANK CAPACITY 80 GALLONS HYDRAULIC OIL CASTROL DUAL RANGE HV 46 (ISO 46) OR EQUIVALENT PUMPS - SYSTEM #1 TWO (2) DANFOSS SERIES 45 J-FRAME OPEN CIRCUIT, VARIABLE PISTON PUMPS. 45CC/REV PER PUMP. ( CU IN/REV PER PUMP) GPM - SYSTEM #1 GPM AT 1800 RPM AND GPM AT 2100 RPM MAXIMUM PSI - SYSTEM #1 4495 PSI ( 310 BAR) CONTINUOUS FEEDER MOTOR RINEER SERIES 15 VANE MOTOR - 5 CU IN/REV (82 CC/REV) - GPM AT 400 RPM TO GPM AT 800 RPM. MAX PRESSURE 3000 PSI (207 BAR) CONTINUOUS. SAE 14 T 12/24 PITCH SHAFT MAIN CONVEYOR MOTOR DANFOSS ORBITAL MOTOR - CU IN/REV (629 CC/REV) - GPM AT 325 FPM. MAX PRESSURE 2900 PSI (200 BAR) CONTINUOUS, 3630 PSI (250 BAR) INTERMITTANT, 4350 PSI (300 BAR) PEAK. 1-1/2" DIA STRAIGHT KEYED SHAFT SIDE CONVEYOR MOTOR DANFOSS ORBITAL MOTOR - CU IN/REV (125 CC/REV) - GPM AT 400 FPM. MAX PRESSURE 3050 PSI (210 BAR) CONTINUOUS, 3990 PSI (275 BAR) INTERMITTANT, 4280 PSI (295 BAR) PEAK1-1/4" DIA STRAIGHT KEYED SHAFT MAGNET BELT MOTOR DANFOSS ORBITAL MOTOR - CU IN/REV (125 CC/REV) - GPM AT 400 FPM.

4 MAX PRESSURE 3050 PSI (210 BAR) CONTINUOUS, 3990 PSI (275 BAR) INTERMITTANT, 4280 PSI (295 BAR) PEAK1-1/4" DIA STRAIGHT KEYED SHAFT TRACK MOTOR KAYABA TWO SPEED MOTOR OPERATES AT CU IN/REV ( CC/REV) AT LOW SPEED AND CU IN/REV ( CC/REV) AT HIGH SPEED. MAXIMUM FLOW PER TRACK IS GPM PER PUMP IN LOW OR HIGH SPEED. PUMP - SYSTEM #2 TUROLLA D-SERIES GEAR PUMP CU IN/REV ( CC/REV) MAXIMUM PSI - SYSTEM #2 4000 PSI (276 BAR) CONTINUOUS GPM - SYSTEM #2 GPM AT 1800 RPM AND GPM AT 2100 RPM LOW TEMPERATURE SET POINT 60 DEG F. (ADJUSTABLE THROUGH PLUS+1 CONTROLLOR ONLY ) RECOMMENDED OPERATING TEMPERATURE 86 DEG F TO 140 DEG F (30 DEG C T0 60 DEG C) HYDRAULIC FLUID CHANGE INTERVALS FIRST CHANGE: 500 HOURS AFTER START-UP. 2000 HOURS OR ONCE A YEAR AFTERWARDS. NOTE: FLUID SAMPLES ARE THE BEST DETERMINATION FOR SUITIBILITY OF CONTINUED USE OF HYDRAULIC FLUIDS UNDER EXTREME OPERATING CONDITIONS. REQUIRED CLEANLINESS CLASS 18/16/13 (ISO 4406-1999)

5 MAGNET/CHUTE MODEL MSI BELT WIDTH 36" MAIN DISCHARGE CONVEYOR BELT WIDTH 48" BELT TYPE 3-PLY 330 PIW CONVEYOR LENGTH 42' 3-13/16" HEAD PULLEY TYPE DRUM WITH 1/2" LAGGING HEAD PULLEY Dimensions 16" DIA X 51" FACE WIDTH TAIL PULLEY TYPE WING TAIL PULLEY Dimensions 12" DIA X 51" FACE WIDTH BEARINGS TYPE - HEAD BALL BEARING 2-BOLT PILLOW BLOCK PULLEY BEARING SIZE - HEAD PULLEY 3-7/16" DIA BEARINGS TYPE - TAIL PULLEY 2-15/16" BALL BEARING 2-BOLT PILLOW BLOCK BELT CLEANER 48" PRIMARY BELT CLEANER WITH PIT VIPER BLADE - TWIST TENSIONER DRIVE TYPE ORBITAL MOTOR - TMT 630 IDLERS CEMA B, 5"DIA CANS X 48" BELT WIDTH RETURN IDLERS CEMA B, 5" DIA CANS X 48" BELT WIDTH SIDE FINES CONVEYOR BELT WIDTH 24" BELT TYPE 2-PLY 220 PIW CONVEYOR LENGTH 13' 11-7/8" HEAD PULLEY TYPE DRUM WITH 1/2" LAGGING HEAD PULLEY Dimensions 12" DIA X 26" FACE WIDTH TAIL PULLEY TYPE WING TAIL PULLEY Dimensions 8" DIA X 26" FACE WIDTH BEARINGS TYPE - HEAD PULLEY BALL BEARING 2-BOLT PILLOW BLOCK BEARING SIZE - HEAD PULLEY "2-7/16" DIA BEARINGS TYPE - TAIL PULLEY BALL BEARING 2-BOLT PILLOW BLOCK BEARING SIZE - HEAD PULLEY 1-15/16" DIA BELT CLEANER 24" PRIMARY BELT CLEANER DRIVE TYPE OMS 125 HYDRAULIC MOTOR IDLERS CEMA B, 4" DIA CANS X 24" BELT WIDTH RETURN IDLERS CEMA B, 4"DIA CANS X 24" BELT WIDTH HOPPER TYPE SKID OVERALL Dimensions (INCLUDES LEGS) 8' 10-1/4"(W) X 206-3/16"(L) X 5' 1-11/16"(H) HOPPER Dimensions 8' 10-1/4"(W) X 206-3/16"(L) X 2' 10-3/8"(H) CAPACITY (LEVEL)

6 9 CUBIC YARDS FEEDER TYPE VIBRATING GRIZZLY FEEDER DRIVE TYPE DIRECT DRIVE HYDRAULIC VANE MOTOR WIDTH 52" LENGTH 16' Crusher Crusher TYPE HORIZONTAL IMPACT Crusher Crusher SERIES 4056 NO. OF BLOW BARS 2 BLOW BARS, 2 DUMMY BARS FEED OPENING 56" X 32" NO. OF APRONS (3) THREE - (2) TWO ADJUSTABLE OAND (1) ONE FIXED TRACK SPECS LENGTH (CENTER) 12' 5-9/16" (3800 mm) SHOE WIDTH INCHES (500 mm) DRIVE TWO SPEED DRIVE - MPH LOW SPEED - MPH HIGH SPEED GEARBOX BONFIGLIOLI T710K PLANETARY GEARBOX; 1:123 REDUCTION RATIO PERFORMANCE TRAVEL SPEED MPH IN LOW SPEED AND MPH IN HIGH SPEED OPTIONS 48" X 36" CROSS BELT MAGNET, FRAME AND CHUTE KIDNEY LOOP HYDRAULIC OIL FILTERING SYSTEM REAR HYDRAULIC STABILIZING LEGS FRONT HYDRAULIC STABILZING LEGS PT TECH EXTENDED WARRANTY OTHER DUST SUPPRESSION H2O SPRAY SYSTEM WITH TWO SPRAY BARS. ONE SPRAY BAR AT THE Crusher INLET AND ONE AT THE Crusher OUTLET. ELECTRICAL REMOTE CONTROL HBC REMOTE WITH PLUS+1 CONTROLLER Revision date: January 1, 2014