Example: marketing
DMC Crimp Dies For a Full Range of Capabilities
DMC Crimp Dies For a Full Range of Capabilities DMC constantly adds new crimp die designs that are comparable to connector and terminal supplier dies or tools. A few of the popular die applications are featured in the following charts. For more options, consult factory .
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
CRIMP TOOL AND ACCESSORY ASSEMBLY TOOLS SIZE …
api.dmctools.comcrimp tool and accessory assembly tools mating end wire barrel af8 afm8 mh860 39-00 wa23 (pos) wa23 (die) installing removal 1 amphenol corp. robert technologies typical contact configuration 6 6n 6 6 p p m39029/48-317 m39029/48-318 ms90559-11 ms90559-12 6 6 wa23-10 wa23-10 wa23-3 wa23-3 by hand by hand drk178-6a
Related documents
HARTING Selection Guide Han-Modular Connectors
www.harting.comCrimp termination, Han ® HC 1 x PE 25 mm² Crimp termination, Han ® HC 1 x PE 16 mm² Crimp termination, Han ® HC Male module (M) Female module (F) 70 - 200 A Han® 200 A Crimp module Han® 100 A Crimp module Han® 100 A Single module Han® 70 A Crimp module Number of contacts Electrical data Cross-section Termination type 1* 200 A / 1000 V ...
PC 707 Crimper - Gates Corporation
www.gates.comthe crimp OD. Insert the coupling into the die set approximately 1/8” below top of die. (See Photo 1.) Slide the die cone assembly under the ram until it stops against back locating pins and push the crimp button and hold. Release the button immediately when the pump stops. Remover coupling and measure crimp diameter, which
MIL-DTL-83513/03 & /04 Micro-D Pre-Wired Crimp …
cdn.glenair.comPre-Wired Crimp Terminated, Metal Shell Connector Micro-D Pre-Wired Pigtails These connectors feature gold-plated TwistPin contacts and mil spec crimp termination. Specify aluminum shells for best availability. 100% tested and backpotted, ready for use. Choose the Wire Type To Fit Your Application
Series 801 Mighty Mouse Double-Start ACME Thread ...
cdn.glenair.com1.ontacts are crimp type, C and used in a rear release retention system 2. Receptacle mates with all quick coupling high density receptacle connectors with same polarization and opposite contact gender 3. Connectors supplied with standard crimp contacts. For coax or other special contacts, order connector less contacts (Contact style
WINEGARD Gateway
d38mfwkkxtsm2m.cloudfront.netcrimp splice, and slide the black ground wire from the Gateway into the opposite end of the splice. Crimp the splice. Step 12 – Mount the wall plate to the wall or panel with the two supplied wall plate screws. Step 13 – Next, connect the WiFi cable with the red tubing to the mating connector that is designated in the #2 slot.
Ideal for…
www.timesmicrowave.comN Male Right Angle EZ-400-NMH-RA-X 3190-2638 <1.35:1 (6) Hex/KnurlSpring Finger Crimp A/G 1.87 (47) 1.42 (36.0) 0.177 (80.2) 28. N Male Right Angle TC-400-NMH-RA-SS 3190-1668 <1.25:1 (2.5) Hex Solder Crimp SS/G 1.5 (38.1) 0.89 (2.6) 0.130 (59.0) 29.
CRIMP TOOL AND ACCESSORY ASSEMBLY TOOLS SIZE …
api.dmctools.comcrimp tool and accessory assembly tools mating end wire barrel af8 afm8 mh860 39-00 wa23 (pos) wa23 (die) installing removal 1 amphenol corp. robert technologies typical contact configuration 6 6n 6 6 p p m39029/48-317 m39029/48-318 ms90559-11 ms90559-12 6 6 wa23-10 wa23-10 wa23-3 wa23-3 by hand by hand drk178-6a