Dulux Wash&Wear Low Sheen AU DD02070

1 AU_DD02070 Dulux wash & wear Low SheenPart A52 LDescriptionWash& wear s Barrier Technology creates a super tough acrylic finish that allows you to wipe away most common marks, scuffs and stains with a wetcloth. Barrier Technology is an advanced formulation of high quality materials that forms a tightly interlocking film. It gives walls painted with wash & wear theultimate protection to stay looking freshly painted for wash & wear Low Sheen (564 Line) (Datasheet AUDD1096).FeaturesHard wearing finish that lastsWithstands wear & tearMark & stain resistantEasy to keep cleanLow VOC: Complies with the requirements for the Indoor Environment Credit in Green Star Australia rating toolsBenefitsSets the standard in paint complete washability: Stain resistance + Scrub Resistance + Burnish flow and levelling properties give satisfying application and reduced likelihood of application hiding power for efficient common marks, scuffs and stains wipe off with a soft wet all interior walls including high traffic And LimitationsAll preparation and painting must conform to AS2311.

2 The Painting of Buildings. Do not use at temperatures below 10 C or when the temperature of surfacemay fall below 10 C during the drying period. Avoid exposure to steam and condensation for 48 hours after application. Although the film is dry to touch in 30minutes, allow 7 days for film to fully cure before colours will show more signs of marking and scuffing than lighter colours. If you are considering using a dark colour in a high traffic area werecommend a higher Sheen level or use of a protective clear Colours: Ensure the paint is thoroughly shaken and stirred immediately after addition of tinter to the can and again before GuideWeatherDesigned for interior use only.

3 Not recommended for and sticks to other painted surfaces over 70 CSolventSensitive to aromatic hydrocarbons and alcoholsAbrasionGood wet and dry burnish resistance and stain resistanceVersion of Dulux datasheet AU_DD02070 approved on Thursday, 23 August 2018 8:08:51 AM (UTC)Page 1 of 4 BLUE, BOLD YELLOW, DEEP, EXTRA BRIGHT, ORANGE, TRUE RED, ULTRA DEEP, VIVID Volatile Organic Content (TVOC) values arecalculated in accordance to the stated methodology withinGreen Star Technical Manuals. The TVOC content istheoretically calculated as the sum total of the known VOCvalues of the product s raw material components. Thesematerials include the base paint plus additional low VOCtinter required for non-factory packaged SprayAirless SprayBrushRollerTypical PropertiesGloss Level5 12 at 60 , 10 20 at 85 ThinnerWaterColourMachine tinted to a wide range of colours.

4 Also available in a range of pre-tinted colours-Natural White, Whisper White, Antique WhiteUSA, Lexicon Quarter, Hogs Bristle, White On WhiteDulux ColourBaseComponents1 Number OfCoats2 Note:Some colours may require more than two coats,especially when painting over a contrasting free. Dry film is <16g/LMeets GBCAVOCR equirement?Touch Dry30 minutesClean UpClean UpDescriptionClean all equipment with By MinMaxRecommendedWet Film Per Coat (microns)626262 Dry Film Per Coat (microns)272727 Recoat Time (min)2 HoursIndefiniteTheoretical Spread Rate (m2/L)161616 Version of Dulux datasheet AU_DD02070 approved on Thursday, 23 August 2018 8:08:51 AM (UTC)Page 2 of 4 Application GuideSurfacePreparationEnsure all surfaces are clean and dry prior to application.

5 Brush down to remove Painted Surfaces: wash down with sugar soap solution and rinse with clean water to remove any dirt, oil or grease. In cases where mould or mildew ispresent, use a household bleach solution. Dilute 1 part bleach with 3 parts clean water. wear gloves and goggles. Use a scouring padwet with bleach solution to lightly abrade the surface and ensure physical removal of stubborn areas of mould growth. Leave the bleachsolution on the surface for 15 minutes, then thoroughly remove by washing down with clean water and wipe dry. In very severe cases,repeat this action to remove all must be sanded to remove loose, peeling, flaking or chalky paint.

6 Sand all gloss and semi gloss surfaces to a dull finishand wipe down with a damp cloth to remove surface dust. Apply one coat of Dulux Acrylic Sealer Undercoat or Dulux 1 Step Acrylic Primer Sealer Undercoat to any areas that have been repaired or which have an uneven gloss Paper-faced Wallboard, Cement Sheet and Brick:Brush down to remove any surface dust. Apply one coat of Dulux 1 Step Acrylic Primer Sealer Undercoat or Dulux Acrylic Interior Timber:Sand smooth. Dust off. Apply one coat of Dulux 1 Step Acrylic Primer Sealer Set Plaster, Fibrous Plaster and Plasterglass:Brush down to remove any surface dust. Apply one coat of Dulux Sealer Binder or Dulux 1 Step Acrylic Primer Sealer Undercoat.

7 Forbest results on bare set plaster and powdery surfaces apply one coat of Dulux Sealer , roller and sprayStir contents thoroughly before and during use with a broad flat stirrer using an up and down scooping action. Apply two coats ofWash& wear Low : Use good quality brushes and rollers. Using poor quality or worn rollers can affect the final finish achieved. Use a mediumnap synthetic or microfiber roller. Pre-wet brushes and rollers with water and remove excess moisture before commencing is usually not required. Under hot conditions up to 50ml per litre of water may be Spray: Suitable for application by all standard spray equipment.

8 If necessary, to aid atomisation, up to 100ml per litreof water may be added for conventional spray or up to 30ml per litre of water for airless times on a day of around 25 C and 50% humidity:Touch Dry - 30 minsRe-coat - 2 hoursNote: Under cooler or humid conditions allow longer times. Ensure temperature is above 10 C during application and And SafetyMSDSN umberDLXGHSEN001037 UsingSafetyPrecautionsKeep out of reach of adequate ventilation. Keep windows and doorsopen during use and while poisoning occurs, contact a Doctor or PoisonsInformation Centre (AUST: 131 126; NZ 0800 764 766).SWALLOWED: Rinse mouth with water. If swallowed, doNOT induce vomiting.

9 Give a glass of : If in eyes, hold eyes open, flush with running waterfor at least 15 : If skin contact occurs, remove contaminated clothingand wash skin : Remove from contaminated INFORMATION (ALL HOURS): AUST 1800 033 111 NZ 0800 734 607 For a Safety Data Sheet contact Dulux Customer Service:AUST 132 525, NZ 0800 800 contact with skin and eyes or breathing vapour andspray mist (dust). wash hands after involved in a fire use water fog, foam or dry breathing products of eye protection and waterproof gloves. Whenspraying wear a dust mask or suitable away from direct not contaminate storm water with paint or not pour left over paint down the drain.

10 Empty paintcontainers should be left open in a well ventilated area todry out. When dry, recycle the container via recyclingprograms. Disposal of empty containers via domesticrecycling programs may differ between local with your local council , keep unwanted paint in sealed containers fordisposal via special chemical waste not reuse container unless thoroughly the case of emergency, please call 1800 033 111 Version of Dulux datasheet AU_DD02070 approved on Thursday, 23 August 2018 8:08:51 AM (UTC)Page 3 of 4 Transport And StoragePack A52L-04912, 52L-04914, 52L-16101, 52L-87663, 52L-87662,52L-84472, 52L-84473, 52L-84474, 52L-88075, 52L-73412,52L-89808, 52L-89972, 52L-73711, 52L-88324, 52L-89965,52L-89967, 52L-A1041 ShipmentNameNot dangerous goods.