Dynamix 2500 Data Collector User Manual - …

1 user Manual Dynamix 2500 data Collector Catalog Numbers 1441-DYN25, 1441-DYN25-Z. Important user Information Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication available from your local Rockwell Automation sales office or online at ) describes some important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. In no event will Rockwell Automation, Inc.

2 Be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this Manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this Manual . Reproduction of the contents of this Manual , in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited. Throughout this Manual , when necessary, we use notes to make you aware of safety considerations.

3 WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may reach dangerous temperatures. IMPORTANT Identifies information that is critical for successful application and understanding of the product.

4 Allen-Bradley, Rockwell Software, Rockwell Automation, Dynamix , Enpac, Emonitor, Datapac, and TechConnect are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Summary of Changes This Manual contains new and updated information. Changes throughout this revision are marked by change bars, as shown to the right of this paragraph. New and Updated This table contains the changes made to this revision. Information Topic Page Calibration 27. Updating the Operating System 34. Rockwell Automation Publication 1441-UM001B-EN-P - September 2012 3. Summary of Changes Notes: 4 Rockwell Automation Publication 1441-UM001B-EN-P - September 2012. Table of Contents Preface Optional Extension Modules.

5 9. Dynamix 2500 data Collector and the Emonitor Software .. 10. Software Compatibilities .. 10. USB Driver and Communication Software .. 10. Operating System .. 10. Document Conventions .. 10. Using Online Help .. 11. Help Screen .. 11. Additional Resources .. 12. Chapter 1. The Dynamix 2500 data Safety Information .. 15. Collector Optical Ports.. 15. Laser Radiation Ports .. 15. Dynamix 2500 data Collector Kit Parts List .. 15. Dynamix 2500 data Collector Optional Parts List .. 16. Parts of the Dynamix 2500 data Collector .. 17. External Connections.. 19. Connector A and Connector B Inputs .. 19. POWER /USB/TRIGGER .. 20. Using the Headphones.. 20. Connecting to the External Power Adapter .. 21. Status Indicators .. 22. Strap Attachment.

6 23. Battery Pack .. 23. Check the Battery Level.. 23. Insert and Remove the Battery Pack .. 26. Battery Maintenance.. 27. Calibration .. 27. Chapter 2. Configuring the Dynamic 2500 Apply Power to the data Collector .. 29. data Collector Installing the USB Drivers for the data Collector .. 30. Install ActiveSync or Mobile Device Center Software.. 30. Install USB Drivers .. 31. Updating the Operating System .. 34. Install the Dynamix 2500 OS Loader Application .. 35. Install the Dynamix 2500 data Collector Firmware .. 37. Restarting the data Collector .. 42. Perform Soft Restart .. 42. Perform Hard Restart.. 42. The data Collector 's Engineer Mode.. 43. Dynamix 2500 data Collector Main Menu.. 45. Main Menu .. 45. Display the Operating System Version Number.

7 46. Rockwell Automation Publication 1441-UM001B-EN-P - September 2012 5. Table of Contents Change the Display Backlight.. 47. Dynamix 2500 data Collector Setup Screen .. 48. Set the Date, Time and Date Format .. 50. Dynamix 2500 data Collector data Collection Screen .. 51. View Settings for Current Measurement Definition .. 54. Setting Up the Dynamix 2500 data Collector .. 55. Configure the data Collector .. 55. Configure the data Collection Options .. 57. Using Memory Cards .. 64. Insert and Remove a Storage Card.. 64. Chapter 3. Setting Up Measurements Measurement Definition Options.. 66. Measurement Types.. 67. Measurement Filters .. 67. Measurement Units .. 74. Setting Up Collection Specifications .. 75. Edit the Measurement Definitions.

8 75. Measurement Input Types.. 76. Measurement Window Types.. 77. Measurement Signal Detection Types .. 77. Measurement Maximum Frequencies.. 78. Measurement Resolution .. 79. Number and Type of Averages .. 80. Order Normalization for Orders Track Spectrum .. 81. Using Frequency Items for the Diagnostic Frequency Cursor .. 82. Setting Up Speed References.. 83. Unsupported Measurement Selections.. 85. Setting Up Measurement Definitions .. 86. Magnitude Measurement Definitions.. 86. Magnitude and Phase Measurements at Orders .. 89. Numeric (Process) Measurement Definitions .. 92. Spectrum Measurement Definitions .. 95. Time Waveform Measurement Definitions .. 98. Voltage Measurement Definitions.. 100. Combine Measurement Definitions for a Location.

9 101. Set Up Tri-axial Measurements .. 102. Setting Up Alarms, Lists, and Inspection Codes .. 104. Alarms and the data Collector .. 104. Lists and the data Collector .. 105. Inspection Codes and the data Collector .. 105. Chapter 4. Loading and Unloading Set Up Communication.. 107. Use the USB Connection.. 107. Install ActiveSync Software .. 108. 6 Rockwell Automation Publication 1441-UM001B-EN-P - September 2012. Table of Contents Create the Connection from the data Collector to a Computer .. 108. Set Up the Current data Collector in the Emonitor software .. 110. Loading Lists to the data Collector .. 113. Prepare the data Collector before Loading .. 113. Initialize the data Collector before Loading .. 114. Loading Inspection Codes.. 116.

10 Load Frequency Labels.. 117. Override the Collect On Alarm Setting.. 117. Select the Lists .. 118. Load Selected Lists to the data Collector .. 119. Display the data Collector Driver Version Number .. 120. Unloading Lists from the data Collector .. 121. Unload Lists in the Emonitor Software .. 122. Unload Multiple Measurements Points in the Emonitor Software.. 122. Unload Unscheduled (Offroute) data from the Dynamix 2500 data Collector .. 123. Unload Measurements using Smart Unscheduled Mode .. 125. Automatically Print Reports after Unloading .. 126. Quickload Files.. 127. Load a list to the Storage Card .. 128. Chapter 5. Collecting and Reviewing data Preparing for data Collection .. 129. Connect a Transducer to the data Collector .. 130.