E2-1 Constant Pressure Pumping System

1 Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433 E2- 1 constant pressure pumping system 06/12/13 PENTEK INTELLIDRIVE Constant Pressure Control Center Maintains Constant & consistent water Pressure for residential well pump systems by automatically adjusting motor speeds to meet changes in water demand. Instantaneous feedback from an electronic Pressure transducer instructs the drive to change the pump motor speed to maintain Constant Pressure . For use with both submersible and above ground well pumps Maintains Constant water Pressure , inside and outside, regardless of how many people or appliances are using water at the same time Fully programmable with 34 adjustable programming parameters Extends the life of the pump and motor by using "Soft Start / Coast to Stop" as well as eliminating frequent on/off Pressure cycling Keypad with backlit LCD display has diagnostic and status indicators Ground detection detects and displays when there is a grounding problem and shuts down the System until problem is corrected EMI/RFI filters eliminate potential interference Removable / replaceable terminal blocks Warranty: 12 months from original installation or 18 months from manufacture Includes.

2 Variable Frequency Drive with NEMA 3R outdoor enclosure, Transducer (1/4" thread size, 18 NPT type) & Transducer Cable (10') One #VFD-SGA Must be installed with each Intellidrive Controller to preserve the Drive's warranty. See next page for information. Motor Type HP Range Input Voltage Max Output Amps Enclosure Brand Part Number 2 Wire* 1 Phase to 1 HP 190V to 265V NEMA 3R Outdoor Pentek PID10 3 Wire* 1 Phase 3 Phase 5A 2 Wire* 1 Phase to HP 11A Pentek 3 Wire* 1 Phase to 2 HP 3 Phase 3 Phase to 5 HP 18A Pentek PID50 PID20 * Select drive by Service Factor amps of pump motor Note: 2 Wire Applications Only Compatible with PENTEK brand 2-Wire Motors Pump Motor Input Output PENTEK Control 2 Wire 1 Phase 1 Phase Up to 1 HP 3 Wire 1 Phase 1 Phase Up to 2 HP 3 Wire 1 Phase 3 Phase Up to 5 HP Complete Product Range with 3 Models: Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433 Storage tank not included.

3 200, 300 & 600 gallon poly tanks available. See "Water Storage Tanks" in section F for more information. Call Davies, we can size a package for each specific application! E2-2 Constant Pressure Pumping System 06/12/13 Will alternate pumps that are connected to the Pentek Intellidrive Controller Designed to equalize wear on the pumps by alternating two Pentek Intellidrive VFD's every 24 hours. This panel alternates which pump is the lead and lag in a duplex System . It can also be used independently of the lead/lag function. Alternate / Off Switch Indicators: Power On, Pump 1 Enabled & Pump 2 Enabled Connection: 4 Terminal Blocks to connect VFD's - Use 18 AWG Wire PENTEK INTELLIDRIVE Surge Protection Kit Line Side Part Number Service Wiring Peak Surge Current MCOV UL 1449, 3rd Ed, Short Circuit Rating EL 1449, 3rd Ed. In Two Power Cords + Ground 72,000A/Phase 36,000A/Mode 130/260V 500 L-G, 900V L-L 10,000A 10,000A Load Side Service Wiring Peak Surge Current MCOV Three Power Cords + Ground 75,000A 320V VFD-SGA One #VFD-SGA Must be installed with each Intellidrive Controller to preserve the Drive's warranty.

4 Line & Load side surge protection for use with any 230 Volt Pentek Drive Line side arrester installed in the circuit breaker. Load side installed on the drive output. Compact size to fit most applications and parallel connection for easy installation Diagnostic LEDs to indicate System power and surge protection Weatherproof design allows for use in most environments Service Voltage: 240 VAC (line side); 240 VAC (load side) Auto reset to handle multiple surges PENTEK INTELLIDRIVE Alternating Control Panel Rated Volts, Hz Cord Enclosure H x W x D Weight Part Number 120 VAC, 50/60 6' NEMA 1 " x " x " 1 lbs VFD-ALT Constant Pressure Pump Package Pump Package for drip tank, cistern, reservoir and well applications Not all package contents are pictured Application Part Number Typical Application: Designed for rural low Pressure water distribution systems PIDPACK Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433 E2-3 Constant Pressure Pumping System 17/04/15 PENTEK PPC3 / PPC5 Variable Frequency Drive Series PENTEK Pump Controllers innovative Pumping solutions for maximizing pump functionality, optimizing pump System design and reducing operating energy costs PENTEK PPC's can be used on all centrifugal motor-driven pumps including close-coupled motor drive, frame mount, submersible and lineshaft turbine pumps, in a wide range of applications PPC Features The PENTEK PPC3 and PPC5 Pump Controllers are programmed with the PENTEK Assistant and pre-jumpered, providing ease of setup for Constant Pressure applications.

5 The PENTEK Assistant defaults to pre-defined parameters and prompts the user for application-specific information. The 'Help' key activates parameter descriptions, providing easy reference to the programming guide. PENTEK Assistant Guides the user through the setup process for Constant Pressure applications, taking less than 2 minutes to program; allows for local or remote operation Includes Macros for both submersible and above-ground pump applications System harmonics evaluation process Additional Application Functions Auto-Restart Functionality - re-starts pump after power loss Easily configured for Constant flow applications by adjusting 2 additional menu parameters Multiple System Setpoints or Operating Condition - includes 2 independent process control setpoints to allow operation under a second process Time function supports 2 daily and weekly START/STOP/BOOST times Process Benefits Variable Speed Control Meets Requirements of process control with Constant Pressure at variable flow conditions or Constant flow at variable Pressure conditions Reduced Energy Costs Calculated energy savings online using BEC2 software at Pump Protection From loss of prime, dead head and blocked suction Motor Protection From ground fault, short circuit, phase loss and imbalance, overload.

6 Undervoltage and overvoltage System Protection (PPC3 only) From harmonics, featuring an input choke that exceeds the performance of a fixed 5% impedance line reactor Phase Conversion The PPC5 will convert 1-phase power into 3-phase power, allowing the use of a 3-phase motor The PPC3 is available in both 1 & 3 phase models PPC3/PPC5 Comparison Features PPC3 PPC5 HP Rating 1-30 1/2-200 Voltages 230, 460 230, 460, 575 Frequency 50/60 Hz 50/60 Hz Floating Choke No Yes Harmonic Signature Good Best No. of Relays 1 3 (ext. to 6 available) Digital Input 2 6 Multiple Pump Capable No Yes Mod. Bus No Yes Enclosure Type NEMA 1 NEMA 1, 12 The output current (or amps) of the PPC must be greater than or equal to the maximum rated motor current Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433 E2-4 Constant Pressure Pumping System 17/04/15 VARIOSPEED Constant Pressure Control Solutions The new VARIO speed series of Constant Pressure controls offered by SJE-Rhombus are an economical, pre-engineered solution for variable speed Pumping applications, including: Submersible Deep Well Pumps Booster Pumps Irrigation Pumps Easy Setup and Operation Energy Saving Phase Conversion VARIO speed VFD can be used in application where three phase power is not available.

7 The drive will convert 240V, single phase power into 240V, three phase power. A three phase motor must be used in all cases Thrust Bearing Control Motor Protection Output phase loss, ground fault, motor overload, motor over temperature Drive Protection Over voltage, input phase imbalance, under voltage, short circuit Automatic System Restart VARIO speed VFD can be configured to automatically restart in Auto Mode after power loss, power spikes, brown outs and dry well conditions Available HP Range (208-240V) HP-20HP (480V) Models available for single phase or three phase supply voltage Energy optomization control Enclosure Style VARIO speed N1 - NEMA 1 indoor enclosure VARIO speed 3R - NEMA 3R indoor/outdoor enclosure (included pump circuit breaker & fan and thermostat on - 20HP models) Controls PID control Adjustable electronic overload Auto start on Pressure drop (adjustable) Auto stop on low Hz (No-Flow - sleep mode) saves energy and protects the pump Display 4 line / 20 character back-lit LCD display is easy to read Rotary / push button for quick menu navigation and programming Green LED run indicator Red LED fault indicator Off/Auto selector switch Pressure Transducer 0-200 PSI, NEMA 4X rated, stainless steel, 1/4" NPT connection, 20 ft.

8 Shield cable Experience the VARIO speed Advantage! Parameters are pre-programmed at the factory Quick installation, simple start-up 100% factory-tested Low Pressure alarm (pipe burst or run dry protection) High Pressure protection System Fail log Includes Pressure transducer UL/cUL listed 5 year limited warranty 1 year limited warranty on transducer CONTINUED ON NEXT PAGE VARIO speed N1 Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433 E2-5 Constant Pressure Pumping System 17/04/15 VARIOSPEED Constant Pressure Control Solutions VARIOSPEED N1 Controller Description Model Output Amp HP Input Phase Output Phase Ship Weight Part Number VARIO speed N1, 240V 1 3 21 lbs. 1041350 VARIO speed N1, 240V 3 1 3 22 lbs. 1041351 VARIO speed N1, 240V 5 3 3 21 lbs. 1041352 VARIO speed N1, 240V 3 3 31 lbs.

9 1041353 VARIO speed N1, 240V 15 3 3 38 lbs. 1041354 VARIO speed N1, 240V 20 3 3 38 lbs. 1041355 VARIO speed N1, 480V 3 3 31 lbs. 1041356 VARIO speed N1, 480V 15-20 3 3 38 lbs. 1041357 NOTE: HP rating is based on standard NEMA b 4-pole motor (used for indication only, use nameplate FLA for sizing). The output voltage of the VFD cannot exceed the incoming voltage. Example: 208V in, 208V out (max). VARIOSPEED 3R Control Panel Description Model Output Amp HP Input Phase Output Phase Ship Weight Part Number VARIO speed 3R, 240V 1 3 31 lbs. 1030983 VARIO speed 3R, 240V 3 1 3 32 lbs. 1030984 VARIO speed 3R, 240V 5 3 3 31 lbs. 1039107 VARIO speed 3R, 240V 3 3 35 lbs. 1030985 VARIO speed 3R, 240V 15 3 3 42 lbs. 1039108 VARIO speed 3R, 240V 20 3 3 42 lbs. 1039109 VARIO speed 3R, 480V 3 3 47 lbs. 1039110 VARIO speed 3R, 480V 15-20 3 3 47 lbs. 1039111 NOTE: HP rating is based on standard NEMA b 4-pole motor (used for indication only, use nameplate FLA for sizing).

10 The output voltage of the VFD cannot exceed the incoming voltage. Example: 208V in, 208V out (max). LINE/LOAD REACTORS (indoor/outdoor rated. Supplied separately) Line/Load Reactors Use with Model Dimensions (in.) Electrical Data Ship Weight Part Number , , 12x12x10 18A, 37 lbs. 1041535 , 12x12x10 55A, 46 lbs. 1041536 12x12x10 83A, 47 lbs. 1041537 12x12x10 21A, 38 lbs. 1041538 12x12x10 35A, 41 lbs. 1041539 Davies Supply Group Ltd. Calgary (800) 661-1346 Lethbridge (877) 595-7707 Saskatoon (877) 355-3377 (403) 244-2161 (403) 381-7707 (306) 933-2433 E2-6 06/12/13 Constant Pressure Pumping System Constant Pressure Controllers Features & Benefits Constant Water Pressure with a wide range of settings (25 to 80psi) Soft Start feature prevents water hammer and increases motor life Works with small Pressure tanks or with larger tanks already in place Smart Reset Technology allows well recovery before restarting the pump Single Phase input power with single phase motor performance (MonoDrive, MonoDriveXT) Single Phase input power with three phase motor performance (SubDrive75,100,150,300) Excellent radio frequency interference shielding UL & CUL Listed Built-in Diagnostics & Protection Surge Protection Underload (low water)